Hyco Jetstream JET1600 Scheda tecnica
Product nstruction Manual
Jetstream 1600
JET1600 (white) & JET1600BSS (brushed stainless steel)
1.6 kW automatic hand dryer
Version 3.2 Jan 2015
V15.6/2
Jetstream 1600_Layout 1 23/06/2015 14:20 Page 1
2
Thank you for purchasing the Hyco Jetstream hand dryer. The JET1600
is suitable for many public washroom applications including restaurants,
shops and shopping centres, office buildings, pubs, motorway services,
factories and supermarkets. Please read and understand these instructions
before commencing installation, and leave them with the user when
installation is complete.
1. Imp rtant safety p ints
• The Electrical installation must be carried out by a qualified electrician in accordance
with the current edition of the .E.E. Wiring Regulations.
• This appliance must be earthed.
• Means for electrical disconnection must be incorporated in the fixed wiring in
accordance with the wiring rules.
• Only connect the hand dryer to a single phase supply with a mains voltage as
specified on the rating plate.
• The hand dryer must be fixed out of reach of a person taking a bath or shower.
• This appliance can be used by children aged from 8 years and above and persons.
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use
of the appliance in a safe way and understand the hazards involved. Children
shall not play with the appliance. Cleaning and user maintenance shall not be
made by children without supervision.
• Do not cover the air inlet or outlet.
Jetstream 1600_Layout 1 23/06/2015 14:20 Page 2
3
2. Installati n
Wall M unting
The hand dryer must be fixed out of reach of a person taking a bath or shower.
• Place the supplied template against the wall at the desired height (see mounting
height recommendations) and mark locations of 4 mounting holes and cable entry
at knockout (KO) location.
Note: For 2 or more dryers , dryers should be no closer than 610mm on centre.
• Remove and retain 2 cover screws and front cover.
• Drill 4 holes holes at locations A, B,C and D of 8mm diameter x 35mm deep.
• Using the fixings supplied, attach the dryer to the wall.
Electrical
This appliance must be earthed.
Means for electrical disconnection must be incorporated in the fixed wiring
in accordance with the wiring rules.
• The power cord should be connected following the colour coding below:
➢Brown: L
➢Blue: N
➢Green / Yellow: E
Hand
Dryer
205mm
287mm
180mm
Jetstream 1600_Layout 1 23/06/2015 14:20 Page 3
3. Operati n
• Shake excess water from hands.
• To activate the hand dryer, place your hands underneath the air outlet to operate
the sensor.
• Rub hands together lightly and rapidly.
• The dryer will stop automatically 1 second after removing hands.
• The dryer will also automatically cut-out after 1 minute of consecutive use.
• To re-start the hand dryer, put hands back underneath and re-operate the sensor.
Air speed adjustment
• Gently prise the filter off from the underneath of the unit so the grille is exposed.
• Use a flat bladed screwdriver small enough to git through the access hole (4.8mm
diameter) in the bottom grille (1). The adjustable potentiometer (20) is visible
through the slots of the grille.
• Gently turn the potentiometer clockwise (CW) to increase power to maximum
(shaft will meet a stop, DO NOT OVERTURN!). Turn the screwdriver gently CCW
to reduce power as required.
At minimum power the unit may not start if low line voltage condition exists.
Sensor adjustment
1. The range is 2” to 13” (50mm to 330mm),
standard settings is 7” (170mm + 20mm)
2. Clockwise: ncreases the sensing range (+)
3. Counterclockwise: decreases the sensing range (-)
4. DO NOT OVERTURN!
4
Hand
Dryer
205mm
287mm
180mm
Hand
Dryer
205mm
287mm
180mm
Hand
Dryer
205mm
287mm
180mm
Hand
Dryer
205mm
287mm
180mm
Jetstream 1600_Layout 1 23/06/2015 14:20 Page 4
4. Maintenance
Periodic cleaning o the unit is recommended to ensure optimum per ormance.
• Disconnect the electrical supply.
• Remove the two cover-mounting screws.
• Remove the cover.
• Clean all dust lint from the interior of the dryer.
• Clean the exterior of the unit using a soft, damp cloth. Do not soak; never use
abrasives to clean the cover.
• Replace the cover. Do not overtighten the screws.
5
Hand
Dryer
205mm
287mm
180mm
Jetstream 1600_Layout 1 23/06/2015 14:20 Page 5
5. Specificati ns
Voltage 230V~50Hz
Power 1.6kW
Air speed (adjustable) 75 - 100m/s
Air volume (adjustable) 87 - 116m3/h
Sound level 77dB
IP Rating IPX1
Weight 5.8kg
6
Hand
Dryer
205mm
287mm
180mm
Jetstream 1600_Layout 1 23/06/2015 14:20 Page 6
6. Tr ublesh ting
Symptom Corrective action - Failure on installation
The dryer will not run Ensure that the breaker supplying the dryer is operational.
f it is, disconnect the power and remove the dryer cover.
Taking suitable precautions to avoid electric shock,
reconnect the power and check for voltage at the terminal
block. Verify that connections are made correctly.
The dryer cycles by itself Ensure that there is no obstruction on or in front of the R
or runs constantly sensor. Clean any dirt or debris off the sensor lens. f
problem persists replace sensor.
The dryer makes a loud Ensure that the supply voltage is correct as specified on
noise and does not run the rating plate. f circuit board has been damaged,
for a complete cycle replace the circuit board and R sensor module.
The dryer runs but air Ensure that the supply voltage is correct as specified on
stream is low pressure the rating plate. The dryer will run weakly if the input
and/or low velocity voltage is too low.
7
Jetstream 1600_Layout 1 23/06/2015 14:20 Page 7
Symptom Corrective action - In service ailure
The dryer will not run Ensure that the breaker supplying the dryer is operational.
f it is, disconnect the power and remove the dryer cover.
Taking suitable precautions to avoid electric shock,
reconnect the power and check for voltage at the terminal
block. Verify that connections are made correctly.
The R sensor only ‘sees’ Ensure that there is no obstruction on or in front of the R
close range objects sensor. Clean any dirt or debris off the sensor lens. Check
variable resistor (VR) for sensor range setting. f problem
persists replace sensor and/or circuit board module.
The heater gets hot but Disconnect the power and remove dryer cover. Check
the dryer is not blowing variable resistor (VR) for speed setting. Disassemble the
any air motor housing. Replace the fan motor. Reassemble.
The dryer only blows Disassemble the blower- motor/fan housing. Test the
cold air during a thermostat for open circuit. Check the heater element
full cycle for signs of burning or breakage. Damaged element
must be replaced.
The dryer runs but air Check the air outlet for obstructions. f none are
stream is low pressure present, disconnect the power. Remove the dryer
and/or low velocity cover. Remove any dust/lint build up from the intake
vent slots. Check VR for speed setting. Disassemble
the motor/fan housing. Check the motor brushes for
worn condition and replace them if necessary.
Jetstream 1600_Layout 1 23/06/2015 14:20 Page 8
Repair parts list
Key Part
1. C0109-4024
C0109-4025
2. D0109-0005
3. G0309-0005
4. A0110-0001
5. G0109-0002
6. E0109-0002
7. G0109-0004
8. AA0110-0002
9. TO209-0017
10. F0209-0007
11. A0110-0003
12. C0109-0013
13. F0301-0006
14. C0110-0001
15. CO109-0026
16. A0101-0022
17. A0101-0020
18. F0801-0003
19. D0101-0008
20. F0509-0001
21. C0109-0018
22. F0209-0011
23. C0101-0031
24. TO110-0005
Description
Steel - White porcelain enamelled - JET1600
Stainless steel - Satin finished - JET1600BSS
Security hex screw (2 reqd.)
Shock absorber
Blower housing - Top
Motor rubber - Large
Motor 700W
Motor rubber - Small
Blower housing - Bottom
Heater element 900W
LED assembly
Air outlet
Sensor bracket
Sensor module
Blower housing bracket
Base plate
Nylon hole bushing
Cable clamp
Terminal block
Grounding screw
VR (variable resistance) 100K
VR bracket
Circuit board module
Security nex wrench
Filter assembly
Jetstream 1600_Layout 1 23/06/2015 14:20 Page 9
Jetstream 1600_Layout 1 23/06/2015 14:20 Page 10
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Hyco Asciugatrice
Hyco
Hyco HD1800 Manuale utente
Hyco
Hyco BLADEW Scheda tecnica
Hyco
Hyco Hurricane HD1600 Scheda tecnica
Hyco
Hyco Tornado Scheda tecnica
Hyco
Hyco Curve Manuale utente
Hyco
Hyco ARC ARCW Scheda tecnica
Hyco
Hyco HURRICANE HD1600 Manuale utente
Hyco
Hyco JETC18W Scheda tecnica
Hyco
Hyco PRISM PRMW Scheda tecnica
Hyco
Hyco BLADE Scheda tecnica
Hyco
Hyco Contour CTRW Scheda tecnica
Hyco
Hyco CYCA26F Manuale di servizio
Hyco
Hyco JET11W Manuale utente
Hyco
Hyco JETS10W Jetstream Slimline Scheda tecnica
Hyco
Hyco Jetstream Blade JETB190W Manuale utente
Hyco
Hyco Jetstream Curve Scheda tecnica
Hyco
Hyco Tornado TOR23W Scheda tecnica
Hyco
Hyco HURRICANE HD1800 Manuale utente
