Hydro digidoor 6 Istruzioni per il montaggio
Installation Instructions and User Guide
ROLL-UP
DOOR OPENER
digidoor 7
• Please read the manual carefully prior to installation and use.
• The installation of the door opener must be carried out by a technically qualied
and licensed person.
• Attempting to install or repair the door opener without suitable technical qualications
may result in property damage, severe personal injury or death.
WARNING
01
CONTENTS
IMPORTANT SAFETY RECOMMENDATIONS 03
1. PACKAGE CONTENTS 05
2. TOOLS 06
3. DOOR REQUIREMENTS 06
4. PRE-INSTALLATION RECOMMENDATIONS 07
5. ATTACHING THE WEIGHT BAR 07
6. CURTAIN FIXING (IF REQUIRED) 08
7. THE RELEASE HANDLE AND CORD 08
8. OPERATING THE MANUAL RELEASE 09
9. LEFT/RIGHT SIDE INSTALLATION 09
10. ATTACHING EXTENSION BAR (IF REQUIRED) 09
11. INSTALLATION PROCEDURE 10
12. CONTROL PANEL INSTALLATION MANUAL 11
13. FUNCTIONAL SPECIFICATIONS 12
14. SAFETY REVERSE TEST 18
15. DESCRIPTION OF EXTERNAL PORT 18
16. SPECIFICATION 19
17. FAULT ALARM CODES, CAUSES AND SOLUTIONS 19
18. COMMON FAULTS AND SOLUTIONS 20
19. PARTS LIST 21
20. MAINTENANCE 22
02
IMPORTANT SAFETY RECOMMENDATIONS
1. The opener is designed and manufactured to meet local regulations. The installer must
be familiar with the local regulations required in respect of the installation of the opener.
2. Unqualied personnel, or those unfamiliar with the occupational health and safety
standards applicable to automatic gates and doors, must under no circumstances carry
out installations or implement systems.
3. Persons who install or service the equipment without observing all the applicable
safety standards will be responsible for any damage, injury, cost, expense or claim
whatsoever any person suffers as a result of the failure to install the system
correctly and in accordance with the relevant safety standards and installation
manual, whether directly or indirectly.
4. For additional safety, we strongly recommend the inclusion of a Photo Cell. Although
the opener incorporates a pressure-sensitive Safety Obstruction Force system, the
addition of the Photo Cell will greatly enhance the operating safety of an automatic
garage door and provide additional peace of mind.
5. Make sure that the garage door is fully open and stationary before driving in or out of
the garage.
6. Make sure the garage door is fully closed, and stationary before leaving.
7. Keep hands and loose clothing clear of the opener and garage door at all times.
8. The Safety Obstruction System is designed to work on STATIONARY objects only.
Property damage, serious personal injury and even death may occur if the garage door
comes into contact with a moving object.
9. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning the use of the appliance by the
person responsible for their safety. Children should be supervised to ensure that they do
not play with the appliance.
WARNING: Failure to comply with the following safety recommendations may result
in property damage, serious personal injury or death. Please read carefully and adhere
to all safety and installation recommendations.
03
10. Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or retailers for
recycling advice.
11. If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualied persons in order to avoid a hazard.
12. Do not allow children to play with door controls, and keep remote controls away
from children.
13. Watch the moving door and keep people away until it is completely open or closed.
14. Take care when operating the manual release – an open door may fall rapidly as a result
of weak or broken springs, or being out of balance.
15. Frequently examine the installation. In particular, check cables, springs and mountings
for signs of wear, damage or imbalance. Do not use if repair or adjustment is needed –
a fault in the installation or an incorrectly balanced door may cause injury.
16. Once a month, check that the drive reverses when the door comes into contact with a
40mm high object placed on the oor. Adjust if necessary and re-check – an incorrect
adjustment may present a hazard for drives incorporating an entrapment protection
system depending on contact with the bottom edge of the door.
17. Disconnect the electric power when cleaning or carrying out other maintenance.
NOTE: If your garage has no service entrance door, we recommend that an outside
quick release is installed. This accessory allows manual operation of the garage door from
outside in case of power failure.
04
1. PACKAGE CONTENTS
1. Instruction manual
2. Clamp bracket, plates, washers (2) and nuts (2)
3. Transmitter (2)
4. Warning label
5. Self-tapping screw (2, used for xing door curtain)
6. Release handle
7. Motor
3
1
4
5
6
7
05
2. TOOLS
1. Marker pen
2. Adjustable wrench for U-bolts already installed on the door (2)
3. Philips-head screwdriver
4. Rope
5. Drill and 6.5mm drill bit
6. Ladder
7. 8mm, 10mm, 13mm sleeve, 300mm extension sleeve (for narrow side mounting)
and socket wrench
Note: Main opener body thickness: 88mm (not including wheel drum). Motor opener body
thickness after lithium battery installed: 93mm (not including wheel drum).
06
3. DOOR REQUIREMENTS
1. Maximum door weight: 130 kg.
2. Maximum door height: 5 m.
3. Maximum curtain area: 20 m2.
4. Protector System (Safety Beams) must be installed if the
force at the edge of closing door exceeds 400N (40 kg).
5. Applicable to door shaft diameter range is
34
-0.5 mm / 32 -1 mm (Optional)
6. Ensure there is a distance of at least 40mm from the edge of the curtain to the edge
of the bracket. If the clearance is small, the rolling door opener cannot be installed.
Please increase the clearance before installation.
4. PRE-INSTALLATION RECOMMENDATIONS
Please complete the following test under no other force than the torsion force of the door
spring to ensure correct balance of the door:
1. Raise and lower the door to determine whether there are
any sticking or binding points. (20kg is the absolute maximum
allowable to raise or lower the door in any position).
2. Do not lock the roller door or remove any rope connected
to the roller door.
3. Lift the door about halfway up and then release it.
The door should be balanced by the spring rebound.
4. If the roller door is not correctly balanced in place, consult
a qualied roller door installation technician before installing the motor.
5. ATTACHING THE WEIGHT BAR
1. If the door has a lifting handle, remove the handle, nuts and bolts. Place the weight bar
over the handle holes, insert the extended bolts through the weight bar, and fasten the
handle back in place.
2. It is important to place the weight bar in the centre of the door as shown.
3. If the door curtain does not have a handle, place
the weight bar in the middle position below the inside
of the door, and use the marker pen to draw two holes
through the screw holes.
4. Drill two holes with a 6.5mm drill bit.
5. Use the bolts, washers and nuts provided
to fasten the weight bar in place.
Note: This motor should not be installed in a damp space or be exposed to the outdoors.
After installation of the roller door, ensure that no part of the roller door extends over public areas
or the pavement. The motor should not be installed on a roller door with a pass-door.
07
6. CURTAIN FIXING (IF REQUIRED)
7. THE RELEASE HANDLE AND CORD
Note: Check whether the curtain and drum wheel have been xed with at least two screws.
If not, insert the supplied self-tapping metal screws where the curtain leaves the roll to
prevent ballooning. Secure these through the curtain into the drum wheel at each end of the
roll. First, close the door curtain under normal conditions. If there is no balloon at the top of
the door curtain, x the second self-tapping screw 33° away from the rst screw position, as
shown in the gure.
Door closed
First screw Second screw
Door ballooning Add screw to x
The manual release mechanism enables the door to be manually
operated during power outages or in an emergency locking.
1. Install the provided clutch extension cord to the ring-pull
of the opener, and ensure it is rm.
2. In the event of a power outage, release the handle
so that the door can be controlled by hand.
3. The RED manual release cord is pre-assembled with the
opener. When the opener is installed, the handle should
be no higher than 1.8m from the oor. The cord may
need to be extended for high door installations.
Ring-pull
Warning
label
Release
handle
Cord
08
8. OPERATING THE MANUAL RELEASE
Release the clutch: While the clutch is in the locked position,
pull the clutch handle down manually. When you hear a click
sound, release the clutch handle. The clutch is now released,
and you can operate the door manually.
Locking the clutch: When the clutch is released,
pull the clutch handle down manually. When the clutch handle
is released when a click sound is heard, the clutch is locked
and the door motor can be used to open and close the door.
LEFT
To install in this direction,
switch the installation
direction before setting
the function. The switching
steps refer to section 12,
2-6 installation mode
settings of left/right.
If the drive leg does not touch the roller door and reel spokes,
extension poles needs to be installed:
• Insert the extension poles into the drive legs.
• Align the holes on the extension poles with the holes
on the drive legs.
• Using the screws provided, secure the extension poles.
RIGHT
Factory default setting
installation direction,
no need to adjust.
Extension poles
Screws
Drive legs
9. LEFT/RIGHT SIDE INSTALLATION
10. ATTACHING EXTENSION BAR
(IF REQUIRED)
Pull down
the handle
Inside garage, looking out
Note: Be careful when operating the clutch. If the torsion spring
in the door fails, the door will instantly close when the clutch is
released, which may cause personal injury and property damage.
09
Indice
