HYPERVOLT Home 2.0 Scheda tecnica
Home 2.0 EV Charger
Operating and Installation Manual
Introduction
Safety Notice
Product Overview !
""!
Installation
•Getting Started" " " !
•Enclosure Parts !
•Mounting " " !
•Accessing the connections !
•Wiring and Connections" " " !
•Power and CT connections " " " " !
•Refitting the LED plate" " " !
•Fitting the front enclosure" " " !
•Monitoring and Protection devices"
•Automated Load Management" " !
•Maximum Operating Current !
Using your charger
•LED Statuses" " !
•App Setup !
•App Basics" " "
•App Settings" " " "
•Charging Modes" " " "
•Scheduling" " " " "!
•App Dashboard" " " "
•Getting it online via Hotspot" !
Regulation Changes Notice!
Technical Specification !
Troubleshooting !
Getting in touch
4
5
6
8
9
10
11
12
13
14
15
16
17
19
20
21
22
23
24
1
2
3
25
26
27
29
Contents
1
Introduction
Thank you for choosing Hypervolt, our team know you will be pleased
by how easy it is to instal and how amazing the functionality is of your
new Home 2.0 Smart EV Charger.
Hypervolt aims to provide customers with state-of-the-art equipment
embracing industry leading smart features backed up by excellent
customer service.
The Hypervolt Home includes advanced built in automatic monitoring
systems for intuitive use and to ensure your safety.
This guide will provide instructions on how to correctly install and
operate your new charger; by reading this guide it will ensure you or if
you are an installer, your customer receives the best experience when
using the charger.!
2
Safety Notice
The installer and end user must read and fully understand the safety instructions provided. Disregard of or actions contrary to the safety
information and instructions contained in this document, printed on the device or by other way given may lead to one or all of the following:!"
•Injury or potential death of the operator, installer and any other third parties.!#
•Improper operation, function and damage of the charger.!#
•Damage to the vehicle on charge, building electrical systems and the surrounding environment.!#
In addition failure to adhere to any of the safety precautions, notices, advice and instructions set out in this guide or by other way given in
relation to either the installation or operation of this and all other Hypervolt products will invalidate the warranty.!"
Legal Notice
This document is intended to be used as a reference guide for the installation and operation of the Hypervolt Home 2.0 EV Charger. The
product images shown are for illustration purposes only and may not be an exact representation of the product. Hypervolt Limited reserves
the right to make changes to the specifications and processes of the product and documentation at any time and without prior notice."
The Hypervolt Home 2.0 charger has been designed, developed and manufactured to satisfy requirements, safety dispositions and norms
in accordance with the directives presented in the declaration of conformity."
Disposal!"
Important information for the correct disposal of the product in accordance with Directive 2012/19/EC. At the end of its
useful life, the product should not be disposed of as urban waste. It must be taken to a collection centre for special and
differentiated disposal or to a distributor that provides this service.
Safety Notice
3
CT Connector
Block
CT Clamp
Charging Cable
Holster
Charging Cable (fitted)
Charging Unit
M4 Enclosure Screws
Getting to know your Hypervolt: Product Overview
What comes in the box ?
LED Status
Indicator
Outer Ring LED
Status
Indicator
Charging Cable
243mm
328mm
101mm
Charging Plug
4
Please read before starting your install!
-Hypervolt products must be installed by suitably qualified trained personnel only. !
-Above all else the Requirements for Electrical Installations as set out in BS7671 (as amended) must be followed
with special attention to section 722.!
-In addition to the above the guidance given in the “Code of Practice for Electric Vehicle Charging Equipment
Installation” (as amended) by the IET must also be followed.!
-If you are unsure about any part of the installation of a Hypervolt product you must obtain clarification from our
technical department before proceeding.!
-After installation and within 48hrs the unit must be registered as having been installed. This is done by scanning
the QR code on the side of the unit or online. This is to validate the warranty, failure to do so will void the
warranty. Installers should aim to do this before leaving site.
Installation: Getting Started
1. Incoming Supply Connections (up to 10mm²)
2. Tethered Cable Connections
3. Incoming Supply Cable (HyperConnect)
4. Tethered Cable with Plug
5. Top Mounting Holes
6. Bottom Mounting Holes
7. Fan Connection
8. CT Connection (Current Clamp)
9. RCD Connection
10. ALM Adjustment Dial
11. Derating DIP Switches
12. Raspberry Pi
13. LED Front Plate Connection
14. Cutout for Additional Cable Gland
15. CP Connection
16. RJ45 Hardwire Connection
17. Ethernet Port
18. RCD
Location of Important Components
5
Installation: Enclosure Parts
A
B
C
A- Back Box !B- LED Plate !C- Front Enclosure
6
Installation: Mounting
STEP 1
Use the cardboard drilling template supplied with your Hypervolt to mark out the mounting holes for the back box (B).!
Your Hypervolt unit and accompanying holster should be fixed between 0.5m and 1.5m above the ground. We recommend the holster position in the diagram is the
best place for it relative to the Hypervolt's position.!
Drill out all 4 fixing holes and fit the top 2 screws (5) leaving them 10mm out. For brick the recommended would be to use a 5.5mm SDS drill, Red plugs & 4x40mm
screws. Hang the Hypervolt on to the top two screws.!
Maximum height 1.5m
Minimum height 0.5m
Before removing the LED Plate (B) we recommend first mounting your Hypervolt charger.
Please note the following;
- The mounting site should be flat, away from extreme external influences and close enough to the EV to prevent the tethered cable causing a trip hazard. "
- There are many different fixings that can be used depending on the material being fixed to so please provide the ones most appropriate, no fixings are supplied."
- The unit comes with a cardboard mounting template however a metal version can be purchased."
- Pole Mounts are available for purchase should you opt to install your Hypervolt as a freestanding charger.
7
STEP 2
Insert the bottom 2 screws (6) then tighten all 4 up pinching the unit up tight to the wall.!
Make sure the unit sits level and adjust if required.!
Installation: Mounting (Continued)
8
Installation: Accessing the Connections
STEP 3
The Hypervolt has a removable LED plate which should be removed to access the connections and then replaced before the front enclosure (C) is fitted.!
To remove simply pull up on the top two tabs and unhook the plate. !
Separate the square white cable joint behind pressing down on the latch to release it. The unit will be shipped with this connector already disconnected however still
take care on first removal just in case.!
Put the LED Plate back in the box to keep it save until you refit it.!
Altri manuali per Home 2.0
2
Indice
Altri manuali HYPERVOLT Caricabatterie per batterie
