Hyster C236 Istruzioni operative

Hyster C236 (H400HD, H400HDS, H450HD, H450HDS)

Internal Combustion Engine Trucks Service Repair Manual

ELECTRICAL SYSTEM

H18-20XM-9, H18-20XMS-9 (H400HD, H450HD,

H400HDS, H450HDS) [C236]

PART NO. 4135453 2200 SRM 1944

SAFETY PRECAUTIONS

MAINTENANCE AND REPAIR

•The Service Manuals are updated on a regular basis, but may not reflect recent design changes to the

product. Updated technical service information may be available from your local authorized Hyster®

dealer. Service Manuals provide general guidelines for maintenance and service and are intended for

use by trained and experienced technicians. Failure to properly maintain equipment or to follow in-

structions contained in the Service Manual could result in damage to the products, personal injury,

property damage or death.

•When lifting parts or assemblies, make sure all slings, chains, or cables are correctly fastened, and

that the load being lifted is balanced. Make sure the crane, cables, and chains have the capacity to

support the weight of the load.

• Do not lift heavy parts by hand, use a lifting mechanism.

• Wear safety glasses.

•DISCONNECT THE BATTERY CONNECTOR before doing any maintenance or repair on electric lift

trucks. Disconnect the battery ground cable on internal combustion lift trucks.

•Always use correct blocks to prevent the unit from rolling or falling. See HOW TO PUT THE LIFT

TRUCK ON BLOCKS in the Operating Manual or the Periodic Maintenance section.

• Keep the unit clean and the working area clean and orderly.

• Use the correct tools for the job.

• Keep the tools clean and in good condition.

•Always use HYSTER APPROVED parts when making repairs. Replacement parts must meet or ex-

ceed the specifications of the original equipment manufacturer.

•Make sure all nuts, bolts, snap rings, and other fastening devices are removed before using force to

remove parts.

•Always fasten a DO NOT OPERATE tag to the controls of the unit when making repairs, or if the unit

needs repairs.

•Be sure to follow the WARNING and CAUTION notes in the instructions.

•Gasoline, Liquid Petroleum Gas (LPG), Compressed Natural Gas (CNG), and Diesel fuel are flamma-

ble. Be sure to follow the necessary safety precautions when handling these fuels and when working

on these fuel systems.

•Batteries generate flammable gas when they are being charged. Keep fire and sparks away from the

area. Make sure the area is well ventilated.

NOTE: The following symbols and words indicate safety information in this

manual:

WARNING

Indicates a hazardous situation which, if not avoided, could result in death

or serious injury.

CAUTION

Indicates a hazardous situation which, if not avoided, could result in minor

or moderate injury and property damage.

On the lift truck, the WARNING symbol and word are on orange back-

ground. The CAUTION symbol and word are on yellow background.

TABLE OF CONTENTS

General .....................................................................................................................................................................1

Electrical Schematic and System Description .......................................................................................................2

Electrical Schematic ........................................................................................................................................... 2

Schematic Location Number ..............................................................................................................................4

Electrical Components ........................................................................................................................................4

Electrical Wires ...................................................................................................................................................4

Wire Identification Number ...........................................................................................................................4

Electrical Wire Colors .....................................................................................................................................6

Wire Harnesses ...............................................................................................................................................6

Harness Interconnection ..............................................................................................................................10

Electrical Connectors ........................................................................................................................................10

Connector Types ........................................................................................................................................... 10

Connector Identification ...............................................................................................................................11

Connector Pin Numbers ...............................................................................................................................11

Connector Description ..................................................................................................................................11

Fuses ..................................................................................................................................................................12

Relays ................................................................................................................................................................ 16

Flyback Diodes ..................................................................................................................................................17

CAN (Controller Area Network) .......................................................................................................................17

Diagnostic ......................................................................................................................................................19

Central Warning Lights and Instrument Panel ..............................................................................................19

Instrument Panel Connector ........................................................................................................................21

LCD Display ......................................................................................................................................................22

Hourmeter Mode ...........................................................................................................................................22

Fault Code Mode ...........................................................................................................................................23

Transmission Calibration .............................................................................................................................23

Fault Code Log Mode ....................................................................................................................................23

Access ........................................................................................................................................................23

Clear ..........................................................................................................................................................24

Exit ............................................................................................................................................................24

General Fault Finding ......................................................................................................................................24

Preparation ...................................................................................................................................................24

Define the Problem Area ..............................................................................................................................24

Identify Possible Causes of Malfunction .....................................................................................................24

Determine the Most Probable Cause ...........................................................................................................24

Fuse Check ....................................................................................................................................................24

Wiring Check ................................................................................................................................................ 25

Component Check .........................................................................................................................................25

Repair and Test .............................................................................................................................................25

Wire Harness Identification and Connector Location .........................................................................................25

Frame Harness Connectors ..............................................................................................................................35

Mast Harness Connectors .................................................................................................................................37

Top Cab Harness Connectors ...........................................................................................................................39

Side Console Harness Connectors ....................................................................................................................41

Cab Underfloor Harness Connectors ...............................................................................................................44

Armrest Harness Connectors ...........................................................................................................................46

ECM Harness Connectors (Tier 3/Stage IIIA) .................................................................................................48

EAS/ECM Harness Connectors (Tier 4F/Stage IV) .........................................................................................49

Powertrain Harness Connectors ......................................................................................................................51

Hoodspine Harness (Tier 3/Stage IIIA) Connectors ........................................................................................52

Table of Contents

TABLE OF CONTENTS (Continued)

Hoodspine Harness (Tier 4F/Stage IV) Connectors ........................................................................................53

This section is for the following models:

H18-20XM-9, H18-20XMS-9 (H400HD, H450HD, H400HDS, H450HDS) [C236]

Table of Contents

Thanks very much for your reading,

Want to get more information,

Please click here, Then get the complete

manual

NOTE:

If there is no response to click on the link above,

please download the PDF document first, and then

click on it.

Have any questions please write to me:

admin@servicemanualperfect.com

General

This manual provides general information on the

electrical system of C236 lift trucks. This manual

provides a link between the electrical schematic

and the actual location of the electrical components

on the lift truck.

The description and replacement procedures for the

electrical system components are located in the

relevant manual for the component. An example

would be a transmission solenoid, which is shown

in Transmission Repair (ZF-WG211)

1300SRM1718.

The actual electrical schematic drawings are shown

in Diagrams 8000SRM1725.

2200 SRM 1944 General

Electrical Schematic and System Description

ELECTRICAL SCHEMATIC

The electrical schematic is laid out over several pa-

ges in Diagrams 8000SRM1725. Each page shows

the electrical connection between the components,

connectors, and wires.

The layout of the schematic is function driven,

which means that each sheet represents one partic-

ular function or area as indicated by the title of the

sheet. The index of the electrical schematic is

shown in Table 1.

Table 1. Electrical Schematic Index

Number Title Contents

1 Index Sheet Title Index

2 Main Power Battery, Key Switch

3 Engine Common and T3 Engine controller and components

4 T4F/EAS Fan Clutch, Tier 4F/Stage IV sensors

5 DEF DEF Sensors, DEF Supply Module

6 XMSN Transmission controller and components

7 Cab Lights Cab roof and interior lights

8 Frame Lights Front and tail lights, reverse alarm

9 Lights Mast lights, flasher, jumper

10 Powered Cab Tilt Powered Cab Tilt

11 Monitoring Instrument cluster, senders, alarms, diagnostics

12 OPS/Park Brake Park brake switch and solenoid, suspension seat

13 Hydraulic Controls Cab Hydraulic controller, levers, Operator Presence

14 Auxiliary Functions Hydraulic Stop Lock-, Twist Lock-, Joystick switches

15 Wipers Wipers and washers, switches, timer

16 Radio/Horn Radio, Horn, DC converter, 12V plug

17 HVAC Heating, Air Conditioning and Ventilation

18 Automatic Greasing Lubrication pump, Lubrication Display

19 Front End FLT Carriage, Slide Shift

20 Connect Overview Connector codes, names and applied harness

21 Wire List List of used wires and their functions

22 Wire List List of used wires and their functions

23 Wire List List of used wires and their functions

24 Wire List List of used wires and their functions

25 Wire List List of used wires and their functions

26 Fuse/Relay Index List of used fuses and their functions

Electrical Schematic and System Description 2200 SRM 1944

Figure 1. Schematic Example

2200 SRM 1944 Electrical Schematic and System Description

Legend for Figure 1

1. ROW LETTER - A

2. COLUMN NUMBER - 30

3. WIRE HARNESS NAME - SIDE CONSOLE

4. WIRE HARNESS NAME - FRAME

5. WIRE CONTINUATION LOCATION- [20, E]

6. MEGA FUSE - 100 AMP

7. WIRE NUMBER AND COLOR - 761-F-WHITE

8. RELAY - STARTER

9. SHEET NAME - ENGINE

10. SPLICE - S761A

11. DIODE BLOCK

12. CONNECTOR - CPS07

13. CONNECTOR - CRP07

14. FUSE - 5 AMP

15. HARNESS DIVIDING LINE

SCHEMATIC LOCATION NUMBER

The schematic is divided into rows with a letter

from A to J and into columns numbered 0 to 9 for

each sheet. See Figure 1.

The column numbering consists of the sheet num-

ber plus the column number. For example, column

57 is the 7th column on sheet 5.

The schematic location number is the combination

of a row letter and column number, which allows

quick identification of a point on the schematic. For

example, [57,A] is the 7th column on sheet 5, row

ELECTRICAL COMPONENTS

Electrical components are indicated by a symbol

and a description that are placed close to each

other on the schematic. An example is the starter

relay on [38,C]. See Figure 1.

ELECTRICAL WIRES

Each electrical wire is indicated by a solid line and

has been identified with an identification number

and a color indication of the wire insulation. If a

wire continues on a different sheet, then the solid

line ends with an arrow and receives in addition

the schematic location number where this wire con-

tinues.

Wire Identification Number

Each electrical wire in the electrical schematic has

an identification number that is also printed on the

insulation of the wires.

The wire identification numbers consist of a func-

tion ID number and when needed a suffix letter.

The function ID numbers are numbered from 1

through 999. Specific ranges of numbers are as-

signed for different function ID groups. See Table 2.

Electrical Schematic and System Description 2200 SRM 1944

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Hyster Motore

Hyster

Hyster G117 Istruzioni operative

Manuali Motore popolari di altre marche

Rotax

Rotax 125 senior MAX evo Manuale utente

Kohler

Kohler K361 Manuale utente

MTD

MTD OHV Series Manuale utente

Kohler

Kohler COMMAND CH18-745 Manuale utente

Mercury

Mercury D4.2L D-Tronic Manuale utente

Selve

Selve SE Plus-RC Series Manuale utente

Perkins

Perkins 1206E-E66TA Manuale utente

Skov

Skov DA 174 Manuale

Rossi

Rossi TX11 Series Manuale utente

Siemens

Siemens SIMOTICS T-1FW3 Foglio di istruzioni

AL-KO

AL-KO PRO 350 Manuale utente

MTU

MTU 12 V 4000 Lx4 Manuale utente

Nanni

Nanni N3.30 Manuale di istruzioni

Nanni

Nanni N5.160 CR2 Manuale utente

KSB

KSB SuPreme Series Istruzioni per l'installazione

Hiwin

Hiwin EM1 Series Manuale utente

Rotax

Rotax 912 i series Istruzioni operative

Siemens

Siemens SIMOTICS XP 1MB1 Manuale utente