I-Tech WBX-6200F-V Manuale utente
WBX-6200F-V
VIA Eden/C3 Fanless Micro PC
User’s Manual
Version 1.0
Copyright Notice
Copyright © 2005
All Rights Reserved.
Printed in Taiwan.
This publication is protected by copyright and all rights are
reserved. No part or whole of it may be reproduced or transmitted
in any form or by any means, electronic or mechanical, including
photocopying and recording without prior consent of I-Tech
TECHNOLOGY CORP.
The information in this document has been carefully checked and
is believed to be accurate. However, I-Tech TECHNOLOGY CORP.
assumes no responsibility for any errors that may appear in this
document. The material contained herein is for informational
purposes only.
The information contained in this document is subject to change
without any notices.
III
Safety Precautions
Before getting started, read the following important
cautions.
1. The WBX-6200F-V may not come equipped with an operating
system. An operating system must be loaded first before
installing any software into the computer.
2. Be sure to ground yourself to prevent static charge when
installing the internal components. Use a grounding wrist strap
and place all electronic components in any static-shielded
devices. Most electronic components are sensitive to static
electrical charge.
3. Disconnect the power from the WBX-6200F-V before making
any installation. Be sure both the system and the external
devices are turned OFF. Sudden surge of power could ruin
sensitive components. Make sure the WBX-6200F-V is properly
grounded.
4. Turn OFF the system power before cleaning. Clean the system
using a cloth only. Do not spray any liquid cleaner directly onto
the system.
5. The WBX-6200F-V is not susceptible to intense shock or
vibration. When assembling the WBX-6200F-V, make sure it is
securely installed.
6. If opening the cover for maintenance is a must, only a trained
IV
technician is allowed to do so. Integrated circuits on computer
boards are sensitive to static electricity. To avoid damaging
chips from electrostatic discharge, observe the following
precautions:
9Before handling a board or integrated circuit, touch an
unpainted portion of the system unit chassis for a few
seconds. This will help to discharge any static electricity
on your body.
9When handling boards and components, wear a
wrist-grounding strap, available from most electronic
component stores.
7. Follow below instructions and notice the caution for replacing
and disposing of the RTC Lithium battery CR2032 for safety
consideration:
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the
manufacturer’s instruction.
V
Acknowledgments
All product names or trademarks are properties of their respective
owners.
VI
（This page does not contain any information）
VII
Table of Contents
How to Use This Manual ................................................. IX
Chapter 1 System Overview .............................. 1
Introduction................................................................... 1
Features........................................................................ 1
System Specification....................................................... 3
System View.................................................................. 4
I/O connectors5
Unpacking ..................................................................... 6
Chapter 2 Getting Started.................................. 7
Setting Up the System .................................................... 7
Installing System Software .............................................. 8
Installing the Drivers....................................................... 9
Chapter 3 BIOS Setup Information.................. 10
Entering Setup..............................................................10
Main Menu....................................................................12
Standard CMOS Setup Menu ...........................................12
Advanced CMOS Setup...................................................13
Advanced CMOS Setup Menu...........................................21
Advanced Chipset Setup Menu.........................................24
Power Management Setup Menu ......................................27
PCI/Plug and Play Setup.................................................30
Peripheral Setup............................................................31
Hardware Monitor Setup.................................................34
BIOS POST Check Point List ............................................35
Flash BIOS Utility ..........................................................41
Appendix A. Jumper Setting and Connectors List
VIII
of CPU Board ................................................... 43
Jumpers Location and list ...............................................43
Jumper List...................................................................44
Jumper Setting..............................................................44
Connector Definitions.....................................................46
Connectors Location......................................................46
Appendix B. System Assembly Reference........ 66
IX
How to Use This Manual
This manual is written for the system integrator, PC technician
and knowledgeable PC end user. It describes how to configure your
WBX-6200F-V series to meet various operating requirements. The
user’s manual is divided into four chapters, with each chapter
addressing a basic concept and operation of the server board.
Chapter 1: System Overview - presents what you have
inside the box and gives you an overview of the product
specifications and basic system architecture for the
WBX-6200F-V series Micro PC.
Chapter 2: System Installation - describes how to set up
the system.
Chapter 3: BIOS Setup Information - specifies the
meaning of each setup parameter, how to get advanced BIOS
performance and update to a new BIOS. Additionally, the POST
checkpoint list will give you a guide for troubleshooting.
The contents of this manual are subject to change without prior
notice. These changes will be incorporated in new editions of this
manual. I-Tech may make supplements or changes for the product
described in this manual at any time.
1
System Overview
Introduction
WBX-6200F-V series are based-on the features of high
performance, cost-effective for VIA C3 or Eden platform with low
power consumption.
WBX-6200F-V is mainly designed for industrial automation
with slim and true fanless feature. With GPIO connector for data
collection and device control, and storage can support internal
DOM and external Compact Flash memory card, or one 2.5” HDD.
Features
The WBX-6200F-V features:
CPU
VIA C3 1GHz, optional for Eden 300/400/533/667/733/800
MHz
System Memory
DDR SDRAM SO-DIMM 256 MB system memory, up to 1GB
Mass Storage Device
Internal 2.5” HDD drive bay with optional anti-vibration kit
IDE interface
UDMA 133 IDE interface x 1 (40 pins) / DMA 33 IDE interface
x 1 (44 pins)
PCMCIA interface
One PCI card-bus interface for Complies with PC Card
Indice
Altri manuali I-Tech Scrivania
