iAN QMC-VA30-01 Manuale utente
ULTRA WIDE 1080P CURVED MONITOR 29.5”
MONITOR CURVO ULTRA WIDE 1080P 29.5” (74.93CM)
MOD. QMC-VA30-01
Please read carefully before using your equipment
and save for future reference.
Por favor léalo cuidadosamente antes de usar su equipo
y guárdelo para uso de futuras consultas.
USER MANUAL / MANUAL DE USUARIO
WARRANTY AND PRODUCT
INFORMATION
These terms shall be governed and construed under laws of the
jurisdiction in which the product was purchased, if any term here is
held to be invalid or unenforceable, such term (in so far as it is invalid
or unenforceable) shall be given no eect and deemed to be excluded
without invalidating any of the remaining terms. Qian reserves the right to
amend any term at any time without notice.
The terms HDMI ®,
HDMI ® High-Denition Multimedia Interface, and the HDMI ® Logo are
trademarks or registered trademarks of HDMI® Licensing Administrator,
Inc.
3
Notices
• Keep the monitor away from water sources or damp places, such as
bathrooms, kitchens, basements and swimming pools.
• Make sure the monitor is placed on a at surface. lf the monitor falls
down, it may cause injury or damage the device.
• Store and use the monitor in a cool, dry and well ventilated place, and
keep it away from emissions and heat sources.
• Do not cover or block the vent hole in the rear casing, and do not use
the product on a bed, sofa, blanket or similar objects.
• The range for the voltage supply of the monitor is printed in the label on
the rear casing. If it is impossible to determine the voltage supply, please
consult the distributor or local power company.
• lf the monitor will not be used for a long period, please cut o the power
supply to avoid electric shock on rainy days or damage due to abnormal
voltage supply.
• Please use a reliable earthing socket, do not overload the socket, or it
may cause re or electric shock.
• Do not put foreign matters into the monitor, or it may cause short
circuits resulting re or electric shock.
• Do not disassemble or repair this product yourself to avoid electric
shock. Should faults arise, please contact the after-sales service directly.
• Do not pull or twist the power cable forcibly.
• There is a polarizing layer (not a protective lm) on the surface of
the screen. Do not peel it o,or the product may be damaged and the
warranty will be voided.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference,
(2)this device must accept any interference received,
(3)including interference that may cause undesired operation.
CAN ICES-3 (B)/NMB-3(B)
4
Packing list
• Please check that the package of the monitor contains all parts. If any
part is lost.
• The color and shape of parts may vary with models. Figures in this User
Manual are for reference only.
• Cables supplied may vary with purchased products. Figures in this User
Manual are for reference only.
• Note: Remaining screws should be kept as spares.
5
Description of buttons
32 4 51
1Power button: Turn the monitor on/o
2Exit/Left button: Exit or return and Input signal.
3Down button: Contextual Model
4Menu button: Enter sub-menus
5Up button: /crosshair shape
Indicator Light Color
Indicator Light
Indicator light:
Steady blue light indicates the power is on and the monitor is running normally.
Red light indicates no horizontal or vertical synchronous signal detected
or no video input signal, and that the monitor is in standby status. Please
make sure your computer is turned on and running normally, then check
that all video cables are fully plugged in and connected to the monitor.
6
Adjusting the monitor
Tilting angle -5.0°(±2.0°)- +20°(±2.0°)
Stand installation
1.Open the cardboard box, take the foam out and lay it at on the table
top. Keep the foam underneath the monitor before attaching the stand.
7
2. Take the support and rotating shaft out assembly and lock them using
two screws.
3. Lock the bracket and base with a screw.
4. Stick the assembled stand into the corresponding slot of the back
shell, gently press the bracket to lock it into the lock, then hold the middle
of the bracket, gently lift the body twice, without loosening your grip, to
make sure that it’s locked.
5. After assembly, simply lift the monitor upright with your hands.
Note: During the set-up of the monitor, do not press the liquid crystal
screen your hands to avoid damage to the screen.
8
Mount Installation
1.Open the cardboard box, take the foam out and lay it at on the table
top. Keep the foam underneath the monitor before attaching the mount.
2. Take out the wall mount assembly and attach the wall mount assembly
with four screws.
3. Note: Mount the assembled product on a hard wall. Do not press
on the screen with your hands during the hanging process to avoid
damaging the screen.
Note: In order to prevent the monitor from falling o the wall, please
install properly and carry out a safety inspection. Do not place or hang
objects on the wall mount, and make sure your wall is at least 2 meters
high.
9
Cable connection
* The bottom interface conguration at the back of the monitor may vary
depending on the product.
* Note: If the power cable or signal cable is damaged, please replace
them with special soft cables and components purchased from our
Manufacture or Maintenance Departments.
HDMI interface
Plug your HDMI cable into the HDMI IN port of the product and the other
end into the HDMI OUT port on your PC.
Plug your HDMI-DVI cable into the HDMI IN port of the product and the
other end into the DVI-OUT port on your PC.
DP interface
Plug your DP cable into the DP IN port of the product and the other end
into the DP OUT port on your PC.
Audio Out
Connect audio outputting devices such as earphones to
the AUDIO OUT interface.
10
DC interface
Please connect the power adapter to the power cable, connect the power
adapter plug to the corresponding power port on your monitor, and then
connect the power cable to a properly grounded power outlet.
OSD menu
Menu description
• The color and shape of the OSD menu in your monitor may be slightly
dierent from the one shown in the gure.
• Settings in the OSD menu may change with updates of its settings
without prior notice.
Press the menu button on the control panel to access the monitor menu.
The detailed information of each menu can be found in the following
sections.
1. Rocker key (Right) to enter the OSD main menu or enter sub-menus.
2. Rocker key (Up) to change crosshair shape or move up in the menu.
3. Rocker key (Down) to move down in themenu.
4. Rocker key (Left) to enter the Input Signal or exit the current screen.
Indice
Lingue:
Altri manuali iAN Monitor
