IBM TotalStorage NAS 100 Manuale utente
IBM TotalStorage NAS 100
Rack Installation Instructions
IBM TotalStorage NAS 100
Rack Installation Instructions
First Edition (August 2002)
© Copyright International Business Machines Corporation 2002. All rights reserved.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.
IBM TotalStorage
™
NAS 100 Rack Installation Instructions
Checking the rack installation kit
Items that you find in the kit:
vTwo telescopic slide rails
vFour brackets
vTwo mounting ears
vOne cable spiral wrap and eight cable ties
vAssorted hardware, including cage nuts, clip nuts, screws, nuts, and washers
vOne Rack Installation Instructions (this manual)
Items that you provide:
vOne Phillips #2 screwdriver
vOne flat-blade screwdriver (if you are using cage nuts)
vOne nutdriver or pair of pliers
© Copyright IBM Corp. 2002 1
Attaching the brackets
The following procedure explains how to attach the brackets to the telescopic slide
rails.
1. Extend the inner server slide rail as far as it will go.
2. Pull the white spring tab on the server slide rail towards its open end and
remove the server slide rail. Set it aside for attaching to the NAS 100 later.
1 Server slide rail
2 Spring tab
3 Telescopic slide rail
1
2
3
2NAS 100 Rack Installation Instructions
3. Attach the first bracket to the front end (the white end) of the telescopic slide
rail:
a. Locate the alignment screw hole on the front end of the outer telescopic
slide rail and align the bracket with it. The alignment screw hole establishes
where each screw will go in relation to the bracket. For most installations,
the alignment screw hole and bracket alignment will be the one illustrated in
the following figure.
1 Alignment screw hole
2 Bracket
3 Outer telescopic slide rail
Note: You will have to slide the inner ball-bearing slide rail and the inner
telescopic slide rail back and forth to align the oval cutout with the
screw hole so that you can insert the screw.
b. Insert an M4 screw through the bracket and in the alignment screw hole,
fasten a washer and an M4 nut to it, and firmly tighten them. Repeat this
step with three more screws in the remaining holes.
4. Extend the slide rails fully.
A
A
1
2
3
IBM TotalStorage
™
NAS 100 Rack Installation Instructions 3
5. Loosely attach the next bracket to the back end of the telescopic slide rail with
four more M4 screws, washers, and nuts, as shown in the following figure.
1 Telescopic slide rail
2 Bracket
Note: Do not completely tighten these screws until you install the slide rail into
the rack. This will make attaching the slide rail to the rack much easier.
After the slide rail is attached to the rack, you can tighten the screws on
the back bracket.
6. Hold the slide rails with the attached brackets up to the rack and check that the
slide rails and brackets will fit in the rack. Make any necessary adjustments to
the back end of the slide rail and its bracket.
7. Repeat this process with the other telescopic slide rail and brackets.
Note: Make sure that you install the screws in the other telescopic slide rail in
exactly the same places that you installed them in the first telescopic
slide rail.
1
2
4NAS 100 Rack Installation Instructions
Mounting the slide rails on the rack
The following procedure explains how to attach the telescopic slide rails to the rack.
1. Determine where on the rack you want to mount the NAS 100.
2. Depending on your rack type, use a screwdriver to insert the cage nuts or slide
the clip nuts into the appropriate holes. You will install two nuts on each side of
the back of the rack and three nuts on each side of the front of the rack (the top
nut is used for the mounting ear on the front of the NAS 100).
Note: Make sure that you insert each of the bottom nuts at the same height on
the rack so that the installed NAS 100 will be level.
1 Cage or clip (shown) nut
2 Front bracket
3 Back bracket
4 Left/right front mounting template
5 Left/right back mounting template
1
2
3
45
IBM TotalStorage
™
NAS 100 Rack Installation Instructions 5
3. Secure the front end of the slide rail to the front of the rack with three M6
screws.
4. Secure the back end of the slide rail to the back of the rack with two M6
screws.
5. Tighten the rear bracket M4 screws of the telescopic slide rail.
6. Repeat this procedure with the other telescopic slide rail and brackets.
6NAS 100 Rack Installation Instructions
Indice
Altri manuali IBM Magazzinaggio
IBM
IBM DCXA-210000 Manuale utente
IBM
IBM totalstorage 200 Manuale utente
IBM
IBM TS2250 Manuale utente
IBM
IBM System Storage DS3400 Manuale utente
IBM
IBM DATA MIGRATION SERVICES - Manuale utente
IBM
IBM AMD Opteron LS21 Manuale utente
IBM
IBM System Storage TS2230 Manuale utente
IBM
IBM DCS3700 Manuale utente
IBM
IBM FC 5026 Manuale utente
IBM
IBM TS4500 Manuale utente
IBM
IBM N Series Manuale utente
IBM
IBM TotalStorage DS4500 Manuale utente
IBM
IBM TotalStorage FAStT EXP700 Manuale utente
IBM
IBM Travelstar 3GN Manuale utente
IBM
IBM System x3690 X5 Manuale utente
IBM
IBM DJSA-210 - Travelstar 10 GB Hard Drive Manuale utente
IBM
IBM DTLA-305040 - Deskstar 41.1 GB Hard Drive Manuale utente
IBM
IBM Tape Library Magstar 3494 Manuale
IBM
IBM 342 7208 Manuale utente
IBM
IBM E Server x 100 Series Manuale utente
