IBT Technologies SE-102-N Manuale utente

SE-102-N

Digital Signage Player

User’s Manual

Version 1.0

(Jan. 2018)

ii SE-102-N

User Manual

No part of this publication may be reproduced, copied, stored in a retrieval system, translated

into any language or transmitted in any form or by any means, electronic, mechanical,

photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc.

(hereinafter referred to as “IBASE”).

Disclaimer

IBASE reserves the right to make changes and improvements to the products described in

this document without prior notice. Every effort has been made to ensure the information in

the document is correct; however, IBASE does not guarantee this document is error-free.

IBASE assumes no liability for incidental or consequential damages arising from misuse or

inability to use the product or the information contained herein, and for any infringements of

rights of third parties, which may result from its use.

Trademarks

All the trademarks, registrations and brands mentioned herein are used for identification

purposes only and may be trademarks and/or registered trademarks of their respective

owners.

SE-102-N User Manual

iii

Compliance

The product described in this manual complies with all applicable European Union

(CE) directives if it has a CE marking. For systems to remain CE compliant, only CE-

compliant parts may be used. Maintaining CE compliance also requires proper cable

and cabling techniques.

This product has been tested and found to comply with the limits for a Class B

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with manufacturer’s instructions, may cause

harmful interference to radio communications.

WEEE

This product must not be disposed of as normal household waste, in

accordance with the EU directive of for waste electrical and electronic

equipment (WEEE - 2012/19/EU). Instead, it should be disposed of by

returning it to a municipal recycling collection point. Check local

regulations for disposal of electronic products.

Green IBASE

This product complies with the current RoHS directives restricting the

use of the following substances in concentrations not to exceed 0.1%

by weight (1000 ppm) except for cadmium, limited to 0.01% by weight

(100 ppm).

•Lead (Pb)

•Mercury (Hg)

•Cadmium (Cd)

•Hexavalent chromium (Cr6+)

•Polybrominated biphenyls (PBB)

•Polybrominated diphenyl ether (PBDE)

iv SE-102-N

User Manual

Important Safety Information

Carefully read the following safety information before using this device.

Setting up your system:

•Put the device horizontally on a stable and solid surface.

•Do not use this product near water or any heated source.

•Leave plenty of space around the device and do not block the ventilation

openings. Never drop or insert any objects of any kind into the openings.

•Use this product in environments with ambient temperatures between 0˚C and

45˚C for the N-series processor or between -40˚C and 70˚C for the E-series

processor.

Care during use:

•Do not place heavy objects on the top of the device.

•Make sure to connect the correct voltage to the device. Failure to supply the

correct voltage could damage the unit.

•Do not walk on the power cord or allow anything to rest on it.

•If you use an extension cord, make sure the total ampere rating of all devices

plugged into the extension cord does not cord’s ampere rating.

•Do not spill water or any other liquids on your device.

•Always unplug the power cord from the wall outlet before cleaning the device.

•Only use neutral cleaning agents to clean the device.

•Vacuum dust and particles from the vents by using a computer vacuum cleaner.

Product Disassembly

Do not try to repair, disassemble, or make modifications to the device. Doing so will

void the warranty and may result in damage to the product or personal injury.

CAUTION

There is a danger of explosion if the lithium-ion battery is replaced with an incorrect

battery. Replace only with the same or equivalent type recommended by the

manufacturer. Dispose of used batteries by observing local regulations.

SE-102-N User Manual

Warranty Policy

•Standard products:

24-month (2-year) warranty from the date of shipment. If the date of shipment

cannot be ascertained, the product serial numbers can be used to determine

the approximate shipping date.

•3rd-party parts:

12-month (1-year) warranty from delivery for 3rd-party parts that are not

manufactured by us, such as CPU,

CPU cooler,

memory,storage devices ,

power adaptor, display panel and touch screen.

＊PRODUCTS, HOWEVER, THAT FAIL DUE TO MISUSE, ACCIDENT,

IMPROPER INSTALLATION OR UNAUTHORIZED REPAIR SHALL BE

TREATED AS OUT OF WARRANTY AND CUSTOMERS SHALL BE BILLED

FOR REPAIR AND SHIPPING CHARGES.

vi SE-102-N

User Manual

Table of Contents

Compliance....................................................................................................iii

Important Safety Information.......................................................................iv

CAUTION .......................................................................................................iv

Warranty Policy..............................................................................................v

Technical Support & Services ......................................................................v

Chapter 1 General Information................................................................1

1.1 Introduction.............................................................................................2

1.2 Features..................................................................................................3

1.3 Packing List ............................................................................................3

1.4 Optional Accessories ..............................................................................3

1.5 Specifications..........................................................................................4

1.6 Overview.................................................................................................6

1.7 Dimensions.............................................................................................7

Chapter 2 Hardware Configuration.........................................................8

2.1 Installations.............................................................................................9

2.1.1 Memory Module Installation......................................................9

2.1.2 Mini-PCIe Card Installation.....................................................10

2.1.3 WiFi / 3G / 4G Antenna Installation.........................................10

2.1.4 HDMI Cable Holder Installation...............................................11

2.1.5 Power Cable Holder Installation..............................................11

2.1.6 Mounting Installation...............................................................12

2.2 Setting the Jumpers..............................................................................13

2.2.1 How to Set Jumpers ...............................................................13

2.3 Jumper & Connector Locations on Motherboard...................................14

2.4 Jumper & Connectors Quick Reference................................................16

2.4.1 Clearing CMOS Data (JP1).....................................................16

2.4.2 Clearing ME Register (JP2)....................................................17

2.4.3 Battery Connector (BAT1) ......................................................17

Chapter 3 Driver Installation .................................................................18

3.1 Introduction...........................................................................................19

3.2 Intel®Chipset Software Installation Utility..............................................19

SE-102-N User Manual

vii

3.3 Intel®Graphics Driver Installation..........................................................21

3.4 HD Audio Driver Installation..................................................................23

3.5 LAN Driver Installation ..........................................................................24

3.6 Intel®Trusted Execution Engine Drivers Installation..............................26

3.7 Intel®Serial IO Drivers Installation ........................................................28

Chapter 4 BIOS Setup............................................................................30

4.1 Introduction...........................................................................................31

4.2 BIOS Setup...........................................................................................31

4.3 Main Settings........................................................................................32

4.4 Advanced Settings................................................................................33

4.4.1 ACPI Settings.........................................................................34

4.4.2 iSmart Controller.....................................................................35

4.4.3 F81964 Super IO Configuration..............................................36

4.4.4 Fintek Super IO Hardware Monitor .........................................39

4.4.5 CPU Configuration..................................................................40

4.4.6 AMI Graphic Output Protocol Policy........................................41

4.4.7 Network Stack Configuration ..................................................42

4.4.8 CSM Configuration.................................................................43

4.4.9 USB Configuration..................................................................44

4.5 Chipset Settings....................................................................................45

4.6 Security Settings...................................................................................46

4.7 Boot Settings.........................................................................................47

4.8 Save & Exit Settings..............................................................................48

Appendix ......................................................................................................49

A. I/O Port Address Map............................................................................50

B. Interrupt Request Lines (IRQ)...............................................................52

C. Watchdog Timer Configuration..............................................................53

Chapter 1

General Information

The information provided in this chapter includes:

•Features

•Packing List

•Specifications

•Optional Accessories

•Overview

•Dimensions

2 SE-102-N

User Manual

1.1 Introduction

The SE-102-N is an ultra slim, fanless digital signage player that measures

only 19.5mm thick. The media player enables the retail, food and hospitality

segments to deliver compelling and valuable content in dual high-definition

HDMI displays to targeted audiences in outdoor environments. It has been

tested to pass extended operating temperatures (-40°C to +70°C) and meet

extreme system reliability requirements that allow its deployment in a wide

range of harsh indoor and outdoor environments. The fanless and noiseless

system comes on board with a lower-power Intel®Atom™ x7-E3950 @

2.0GHz quad-core processor with an Intel®HD Graphics, which combines

efficiency and excellent performance, ensuring industrial-grade reliability for

stable operation. It has two dual-channel DDR3L-1866 sockets to provide up

to 8GB memory and 64GB mSATA SSD for faster system boot and low heat

emission.

The SE-102-N’s super-slim chassis can fit into the tightest spaces behind

displays and offers an array of connectivity options including a Gigabit

Ethernet, audio, USB 3.0 ports, and two HDMI interfaces supporting 4K UHD

resolution. Powered by a 60W adaptor, the SE-102-N also has a mini-PCIe

slot for optional WiFi, Bluetooth, 4G and video capture functions. The player

has two HDMI outputs together supporting independent audio outputs, as well

as built-in hardware EDID (extended display identification data) simulation to

prevent screen convergence problems and issues due to cable disconnection

or failure to identify EDID. It also comes with IBASE’s unique iSMART

intelligent energy-saving and Observer monitoring technologies that feature

automatic power on/off scheduling, automatic power recovery, low

temperature boot protection and hardware monitoring.

General Information

SE-102-N User Manual

1.2 Features

•Outdoor, compact, fanless and super slim digital signage player

•iSmart for EuP/ErP auto-scheduler, power saving and power resume

•With onboard Intel®Atom™x7-E3950 2.0 GHz [i-Temp support] or Intel®

Pentium®N4200 2.5 GHz

•Intel®HD Graphics (Gen 7-LP) 4EU

•2 x DDR3L-1866/1600 SO-DIMM, dual channel, expandable up to 8 GB,

non-ECC

•2 x HDMI 1.4b with hardware EDID emulation

•1 x GbE LAN, 1 x RJ45 COM RS-232

•1 x Mini-PCIe (full-size) for WiFi, Bluetooth, or 4G LTE options

•SIM card slot

•Wide-range operating temperature from -40°C to 70°C (without adapter

for E-series only)

1.3 Packing List

If you buy a barebone SE-102-N, your product package should include the

items listed below. If any of the items below is missing, contact the distributor

or the dealer from whom you have purchased the product.

Drivers and this user manual are downloadable from our website.

•SE-102-N Digital Signage Player x 1

•Power Adaptor x 1

•Power Cord x 1

•Flat Head Screw for Mini-PCIe Card (M2 x 0.4 mm) x 4

1.4

Optional Accessories

We provides

optional accessories as listed below. Please contact us or

your dealer if you would like to order any item(s).

•

Power Cable Holder (with 1 round head screw)

•

HDMI Cable Holder (with 2 round head screws)

Indice

Altri manuali IBT Technologies Lettore multimediale

IBT Technologies

IBT Technologies SI-323-N Manuale utente

Manuali Lettore multimediale popolari di altre marche

Visual Land

Visual Land Impulse Manuale utente

limHD

limHD 200i Manuale utente

Transcend

Transcend DMP10 Manuale utente

Philips

Philips GoGear Muse SA2MUS08 Manuale utente

Fantec

Fantec MM-HDRL Manuale utente

Dune HD

Dune HD Duo 4K Manuale utente

IAdea

IAdea HMP-505S Manuale utente

Camos

Camos MMS-1000 Manuale utente

Energy

Energy 75 Series Manuale utente

Z3 Technology

Z3 Technology DME-03 Manuale utente

Sony

Sony SVR-2000 Guida utente

Meicheng

Meicheng HD-1080K12 Manuale utente

DENAFRIPS

DENAFRIPS ARCE Manuale utente

Topaz

Topaz CMS Media Player Istruzioni per l’uso

InFocus

InFocus LightCast Manuale utente

IconBiT

IconBiT XDS1003D Manuale utente

Quanmax

Quanmax QDSP-2090 Series Manuale utente

Samsung

Samsung MP-80S Manuale utente