iCanTek iCanView220 Manuale utente
j}YYWVYYW~
User’s Guide
Rev1.0(Aug. 2006)
iCanView220/220W User’s Guide
Rev.1.0 (Aug. 2006) Y \Z
Note
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generate, use and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures
zReorient or relocate the receiving antenna.
zIncrease the separation between the equipment and receiver.
zConnect the equipment into and outlet on a circuit different from that to which
the receiver is connected
zConsult the dealer or an experienced radio/TV technician for help.
Directions
iCanView220 series network camera are designed for indoor use only. When using iCanView220
outdoors or in an environment that exceeds the limited range, you must separately use a water-
resistant case.
Be careful not to cause any physical damage by dropping or throwing the iCanView220 /220W
network camera. Especially keep the network camera out of reach from children.
Do not disassemble iCanView220/220W. You will be excluded from After Service when
disassembled.
Use only the power adapter provided with the iCanView220/220W.
If you would like to use the iCanView220/220W for security, monitoring, please check the
legal regulations within the country.
iCanView220/220W User’s Guide
Rev.1.0 (Aug. 2006) Z \Z
This appliance and its antenna must not be co-located or operating in conjunction with any other
antenna or transmitter. A minimum separation distance of 20 cm must be maintained between the
antenna and the person for this appliance to satisfy the RF exposure requirements.
Revision History
Date Rev No Description
Aug. 14,
2006-08-14 1.0 Creation of the document
Caution
Any changes or modifications in construction of this device which are not explicitly
approved by the party responsible for compliance could void the user’s authority to operate
the equipment.
iCanView220/220W User’s Guide
Rev.1.0 (Aug. 2006) [ \Z
1. IntroductionUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU \
1.1. OverviewUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU \
1.2. Features of iCanView220/220WUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU \
1.3. Applications of iCanView220/220W UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ]
2. Product Description UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU^
2.1. Contents UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^
2.2. Preview UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^
2.3. Physical description UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU _
2.4. PC Requirements UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU XY
2.5 Quick Installation GuideUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU XY
3. Connecting iCanView220/220W to NetworkUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU X]
3.1. Connecting to LAN UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU X]
3.2. Connecting to xDSL/Cable Modem UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU X^
4. IP-InstallerUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU X`
4.1. Main window of IP-InstallerUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU X`
5. Configuring iCanView220/220W in Administrative Mode UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUYW
5.1. Log On UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU YW
5.2. Basic SetupUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU YY
5.3. Network Configuration UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y[
5.4. Wireless Configuration UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y^
5.5. CCD Adjustment UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y`
5.6. User Admin & Time Setup UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ZX
5.7. Sensor & Capture Setup UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Z[
5.8. Alarm Device SetupUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Z]
5.9. Motion Region Setup UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Z_
5.10. PTZ SetupUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU [W
5.11. Encryption Set up UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU [Y
5.12. Upgrade & ResetUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU [[
5.13. Status ReportUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU []
6. Tips for Using iCanView220/220W UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU [^
6.1. ALARM-IN and ALARM-OUT UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU [^
6.2. Trouble ShootingUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU \W
6.3. Web Viewer UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU \Y
6.4. How To Upgrade Your iCanView220/220W System UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU \[
Table of Contents
iCanView220/220W User’s Guide
Rev.1.0 (Aug. 2006) \ \Z
1. Introduction
1.1. Overview
The iCanView220/220W is a state-of-the-art network camera which transmits synchronized video
and audio data in real time with D1 resolution at full frame rate. This is possible through MPEG4
CODEC technology, which provides high quality video with highly compressed data streams. The
iCanView220/220W can be connected, controlled and monitored from a remote location through an
IP connection over internet or intranet. Unlike CCTV or DVR, the iCanView220/220W is easy to
install and owner will experience cost and space savings in the installation owing to the state of the
art technologies embedded in the system. Based on Embedded Software Solution (Embedded Web
Server, Embedded Streaming Server, Network Protocol), the iCanView220/220W ensures
unprecedented performance and stability to be an ideal network camera solution for system
integration solutions.
iCanView220/220W is offered with standard Ethernet interface while iCanView220/220WW is
offered with embedded WiFi solution.
1.2. Features of iCanView220/220W
y1 channel synchronized real time Video/Audio streaming
MPEG-4 video, ADPCM audio.
yBi-directional audio communication
Real time audio communication between iCanView220/220W and Client PC
yThe viewer assisted recording and playback functions.
y1 Alarm sensor input/1 relay output
yMotion detection – Up to 3 motion detection zones
Arbitrary shape motion detection zone
Motion detection can initiate video recording, which is sent to the user through FTP and/or E-mail.
yResolution
- NTSC : 704x480, 352x240, 176x144.
- PAL/SECAM : 704x576, 352x288, 176x144
yRS-485 interface for Pan/Tilt device connection
yRemote administration control
Entire operational parameter set up, Software upgrade
yEmbedded WiFi interface (iCanVeiw220W only) – IEEE 802.11a/g
yProprietary PoE (Power over Ethernet) for convenience of installation and cost savings
iCanView220/220W User’s Guide
Rev.1.0 (Aug. 2006) ] \Z
1.3. Applications of iCanView220/220W
ySecurity surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government
facilities, military, etc.,
yReal time Internet broadcasting
yRemote monitoring (hospitals, kindergartens, traffic, public areas, etc.,)
yTeleconference (Bi-directional audio conference)
yRemote Learning
yWeather and environmental observation
iCanView220/220W User’s Guide
Rev.1.0 (Aug. 2006) ^ \Z
2. Product Description
2.1. Contents
Open the package and check if you have the followings:
Components Description Remarks
iCanView220/220W iCanView220/220W Network
Camera/Server
Power adapter Input : 100~250V 50-60Hz
Output : +12V, 1.0A Standard Power
AC power cable AC 250V, 10A~16A
Video cable
Cable for analog video output from
camera module inside of network
camera
Antenna iCanView220W only
CD-ROM Software & User’s Guide
Quick Reference Guide Quick installation guide Will be provided
2.2. Preview
iCanView220/220W IP-Installer i-NVR
1CH MPEG-4 Network
Camera
PC software to allocate an IP
address to the
iCanView220/220W
PC software to view and record
the A/V streaming data
transmitted from
iCanView220/220W
iCanView220/220W User’s Guide
Rev.1.0 (Aug. 2006) _ \Z
Analog Video Out
2.3. Physical description
2.3.1. Switches and Knobs for the adjustment
Figure 2-1. Front view of CanView220/220W
2.3.2. Bottom view and Cable Harness
BLC,AGC,FL Switch
Reset
iCanView220/220W User’s Guide
Rev.1.0 (Aug. 2006) ` \Z
Sensor In/Relay Out 100BaseT(RJ-45)
Line Out MIC/Line In RS232C DC Power
Figure 2-2. Rear views and Cable of iCanView220/220W
yMIC. /LINE In : Connect external audio source or microphone. If external audio is connected,
embedded microphone will be disabled.
Use Standard stereo earphone jack for the connections.
Audio In
Ground
Not used
Audio In
Ground
Not used
Audio out
Ground
Not used
Audio out
Ground
Not used
Figure 2-3. Pin assignment of the plug for MIC/LINE In (left) and
LINE OUT (right)
yLine Out : Connect speakers with built in amplifier. Audio from remote site is output through
iCanView220/220W User’s Guide
Rev.1.0 (Aug. 2006) XW \Z
Line out in bi-directional audio mode.
Use Standard stereo earphone jack for the connection.
y100BaseT (RJ45) : 100Mbps Ethernet connector (RJ-45) with proprietary PoE.
- Link LED : Continuous yellow light means that network cable is plugged in. It will flicker
when there is traffic.
- Status LED: Green color indicates that the camera is in normal operation mode, while RED
color indicates that the camera is in abnormal condition.
yRS-232C
3 Pins from the connector are assigned for RS-232 port. Please note that the bottom most pin
is numbered as 1.
Pin Description Misc.
2 TxD of RS-232C For debugging & factory use only.
3 RxD of RS-232C For debugging & factory use only.
5 Ground of RS-232C For debugging & factory use only.
yAnalog Video Output
This can be used for installing network camera and adjust the viewing angle etc.,
A video cable which is supplied with network camera is used to get the analog video signal
from the camera module and to output to analog monitor.
To Analog Video Out of network camera To Analog Monitor
Figure 2-4. Analog Video Cable
yBLC -isjO㡃ὧ⽊㩫₆⓻P
iGsGj㦮 㭖Ⱖ⪲㍲ 㡃ὧ㦮 ┾㩦㦚 ⁏⽋䞮₆ 㥚䞲 ₆⓻
䞒㌂㼊Ṗ 㡃ὧ㌗䌲 䞮㠦㍲ 㾂㡗♶ ἓ㤆 ⳾┞䎆㠦 㨂㌳ 㔲S ⺆ἓ㦖 ἶ 䞒㌂㼊⓪ 㠊⚷Ợ ♮㠊 䞒㌂㼊Ṗ 㔳⼚⓻
㌗䌲Ṗ ♮⓪ ộ㦚 㰖䞮₆ 㥚䞮㡂 ╖⚦♲ ₆⓻㦒⪲S 䞲Ⱎ❪⪲ 㡃ὧ㌗䌲㦮 䢪㰞㦚 Ṳ㍶㔲䋺₆ 㥚䞮㡂 ㌂㣿♮⓪ ₆
Altri manuali per iCanView220
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali iCanTek Telecamera di sicurezza
iCanTek
iCanTek iCanView232 Manuale utente
iCanTek
iCanTek iCanView 240 Manuale utente
iCanTek
iCanTek iCanView 110 Manuale utente
iCanTek
iCanTek iCanView372 Manuale utente
iCanTek
iCanTek iCanView270 Manuale utente
iCanTek
iCanTek iCanView 230 Manuale utente
iCanTek
iCanTek iCanView220 Manuale utente
iCanTek
iCanTek iCanView290PT Manuale utente
iCanTek
iCanTek iCanView 222 Manuale utente
