ICD NeoGCP i7 PLUS+ Manuale utente

NeoGCP i7 PLUS+

User’s Guide

(Rev. N)

REV. N

NeoGCP i7 PLUS+

- 2 -

C A U T I O N

1. It is recommended to use RPM measurement method as MPU to prevent start motor damage when using

Doosan engine.

2. If RPM measurement method is frequency, oil pressure switch is set to not use, and voltage is not

generated at engine CRANK-ON, the start motor may be damaged.

■MPU Method Setup

Setup

TEETH(FACTOR)

1. Select [SYSTEM] then [ENTER] on Menu screen.

2. Press [▼] 2 times, [▶] 2 times, select [TEETH(FACTOR)], then press [ENTER].

3. Input Teeth number, then press [ENTER].

RUN-STATE OP-

SWITCH

Use / Not use

1. Select [CONTROL] then [ENTER] on Menu screen.

2. Press [▼] 3 times, [▶] 2 times, select [OIL PRESS SENSOR] then [ENTER].

3. Select [Use] then press [ENTER].

RUN-STATE OP-

GAUGE

1. Select [CONTROL] then [ENTER] on Menu screen.

2. Press [▼] 3 times, [▶] 1 time, select [RUN-STATE OP-GAUGE] then setup oil

pressure.

※6.5 Refer to Crank ON/OFF

■Doosan Engine Gear Teeth

Gear Teeth

Doosan Engine Model

129

DB33, PO34TI, DB58

140

D1146, D1146T

146

PO86TI

152

P126TI-3, P126TI, P126TI-II

160

P158LE-III, P158LE, P158LE-1, P158LE-2, P180LE-II, P158LE, P222LE-1, P222LE,

P222LE-II, P222FE-II

※Information above written in request of Doosan Commercial Engine(DSCE).

Start motor ON/OFF record stored in ALARM HISTORY.

If start motor is damaged due to ignoring above caution, free A/S from DSCE will NOT be possible

even within warranty period.

REV. N

NeoGCP i7 PLUS+

- 3 -

- This manual can be applied to NeoGCP i7 PLUS Ver. 5.05 and up. (Some functions 3.13 and up)

- Contact us for old version manuals.

Firmware

Version

Application

Manual Version

Changes

3.05a

Rev. H

3.06

Rev. I

- Protection setup change of OCR and OCGR

(Constant, Inverse, Instant added)

- Inverse Characteristics Curve changed

- Power factor display upgraded

- 1P2W added

4.00

Rev. K

- Ext-Module EP20 function added, ECU type setup added

4.06~

(3.13~)

Rev. L

- Protection function change of OVR, OCR, OCGR

- SVR added

- IDLE TIME setup possible up to 600[s]

5.06~

(3.13~)

Rev. N

- Setting/Breaker Type: MC added, ACB open delay added

- Added CoolDown function in manual operation

- Check -> subdivided into RPM check, OPG check, and OPS

check

- Governor Delay: changed from 0~90sec to -60~60sec.

(-) time is output before the starter motor

- Added User Timer Input(in DI) and C_User Timer (in DO)

- For ECU Type engine, NeoGCP g7 model is recommended

REV. N

NeoGCP i7 PLUS+

- 4 -

Table of Contents

1. NeoGCP i7 ................................................................................................................ 9

NeoGCP i7 ............................................................................................................................91.1.

Special Features ..................................................................................................................91.2.

Product Image .....................................................................................................................91.3.

Specification ........................................................................................................................91.4.

2. Button usage and LED Lighting Status ..................................................................... 10

Button usage .....................................................................................................................102.1.

LED Lighting Status ............................................................................................................102.2.

3. LCD Display Status .................................................................................................. 11

Start Screen .......................................................................................................................113.1.

Main Screen .......................................................................................................................113.2.

Alarm Screen .....................................................................................................................123.3.

Menu Select Screen ...........................................................................................................123.4.

Menu Select Screen ...........................................................................................................123.5.

4. NeoGCP i7 Cable Specification and Size ................................................................... 13

NeoGCP i7 Cable Specification ...........................................................................................134.1.

NeoGCP i7 Size ..................................................................................................................134.2.

5. NeoGCP i7 Input and Output Port ............................................................................. 14

Number [1], Number [2] Vdc ± .........................................................................................155.1.

Number[3] ~ Number[5] MAIN R, S, T ...............................................................................155.2.

Number[6] ~ Number[9]GEN PT U, V, W, N .......................................................................165.3.

Number[10], Number[11] MPU ± .....................................................................................165.4.

Number [12] ~ Number [14] RS485 ± ...............................................................................165.5.

Number [15] ~ Number [24] DI-CONFIG ...........................................................................175.6.

Number [25] ~ Number [40] DO-CONFIG .........................................................................175.7.

Number [41] ~ Number [46] Sensor Input .........................................................................175.8.

Number [47], Number [48] GEN ZCT K, L ..........................................................................185.9.

REV. N

NeoGCP i7 PLUS+

- 5 -

Number [49] ~ Number [52] GEN CT U, V, W, N ..............................................................185.10.

6. Operation Sequence ............................................................................................... 19

Control Function According to Operation Mode ..................................................................196.1.

Operation Order ................................................................................................................196.2.

Ready ................................................................................................................................196.3.

PRE-CRANK .......................................................................................................................206.4.

CRANK ON/OFF .................................................................................................................206.5.

IDLE RUNNING ...................................................................................................................216.6.

BUILD-UP ..........................................................................................................................216.7.

RUNNING ...........................................................................................................................216.8.

COOLDOWN ......................................................................................................................216.9.

STOP ...............................................................................................................................226.10.

MANUAL ..........................................................................................................................226.11.

AUTO ...............................................................................................................................226.12.

FIRE .................................................................................................................................226.13.

SCHEDULED-RUN ...........................................................................................................236.14.

7. SYSTEM .................................................................................................................. 25

POWER (P) ........................................................................................................................257.1.

FREQUENCY (F) .................................................................................................................257.2.

VOLTAGE (V) .....................................................................................................................257.3.

CURRENT (I) ......................................................................................................................267.4.

GR CURRENT (GRI) ............................................................................................................267.5.

GEN WIRING (WIRE) ...........................................................................................................26

7.6.

EXT-MODULE (EX) ............................................................................................................267.7.

ECU TYPE (EP) ...................................................................................................................277.8.

PT RATIO (PT) ...................................................................................................................277.9.

CT RATIO (CT) .................................................................................................................287.10.

GR CT RATIO (ZCT) ..........................................................................................................287.11.

RPM (RPM) ......................................................................................................................287.12.

REV. N

NeoGCP i7 PLUS+

- 6 -

GOVERNOR TYPE (GOV) ..................................................................................................287.13.

TEETH(FACTOR)(TEETH) ................................................................................................287.14.

BREAKER TYPE (TYPE) ....................................................................................................287.15.

BREAKER AUX CHECK (AUX) ............................................................................................297.16.

BUTTON BEEP (BEEP) .....................................................................................................297.17.

ALARM HORN TIME (HORN) .............................................................................................297.18.

BACK-LIGHT TIME (LIGHT) ..............................................................................................297.19.

DATE SETUP (DATE) .......................................................................................................297.20.

TIME SETUP (TIME) .........................................................................................................297.21.

TIME COMPENSATION (CLOCK) ......................................................................................307.22.

8. SENSOR-SET .......................................................................................................... 30

Sensor Use / Not use ..........................................................................................................308.1.

RTD Sensor Resistance Value and Output setup .................................................................308.2.

Fuel Level Gain and Offset .................................................................................................308.3.

When Using EP20 ..............................................................................................................318.4.

9. DI-CONFIG ............................................................................................................. 32

USER FAULT ......................................................................................................................339.1.

USER FAULT(RUN) .............................................................................................................339.2.

USER FAULT(STOP) ...........................................................................................................339.3.

EM’CY STOP S/W ...............................................................................................................339.4.

COOLANT TEMP S/W .........................................................................................................349.5.

OIL PRESS S/W ..................................................................................................................349.6.

COOLANT LEVEL S/W ........................................................................................................34

9.7.

NO CHARGING S/W ............................................................................................................349.8.

FAIL TO START ...................................................................................................................349.9.

FAIL TO STOP ..................................................................................................................359.10.

BUILD-UP EXPIRE ............................................................................................................359.11.

OVER SPEED ....................................................................................................................359.12.

OCGR ...............................................................................................................................359.13.

REV. N

NeoGCP i7 PLUS+

- 7 -

BREAKER AUX ..................................................................................................................359.14.

UVR SIGNAL .....................................................................................................................359.15.

FIRE-RUN ........................................................................................................................369.16.

BLOCK .............................................................................................................................369.17.

MANUAL ..........................................................................................................................369.18.

AUTO ...............................................................................................................................369.19.

GEN START ......................................................................................................................379.20.

GEN STOP ........................................................................................................................379.21.

BREAKER CLOSE ..............................................................................................................379.22.

BREAKER OPEN ................................................................................................................379.23.

ALARM RESET ..................................................................................................................389.24.

IDLE RUN .........................................................................................................................389.25.

OIL PRESS LH S/W ...........................................................................................................389.26.

OIL PRESS RH S/W ...........................................................................................................399.27.

COOLANT LH S/W ............................................................................................................399.28.

COOLANT RH S/W ...........................................................................................................39

9.29.

OIL TEMP S/W .................................................................................................................399.30.

10. DO-CONFIG .......................................................................................................... 40

C_PRE-CRANK .................................................................................................................4110.1.

C_CRANK .........................................................................................................................4110.2.

C_GOVERNOR ..................................................................................................................4210.3.

C_BREAKER CLOSE ..........................................................................................................4210.4.

C_BREAKER OPEN ............................................................................................................4210.5.

C_ALARM BUZZER ............................................................................................................4310.6.

C_ALARM RESET ..............................................................................................................4310.7.

C_IDLE SPEED ..................................................................................................................4310.8.

C_RATED SPEED ..............................................................................................................4310.9.

S_MAINS ON ..................................................................................................................4410.10.

S_MAINS OFF .................................................................................................................4410.11.

REV. N

NeoGCP i7 PLUS+

- 8 -

S_GEN START ................................................................................................................4410.12.

S_GEN RUNNING ............................................................................................................4410.13.

S_BLOCK MODE, S_MANUAL MODE, S_AUTO MODE, S_FIRE-RUN .................................4410.14.

S_ALL ALARM, S_WARNING, S_HEAVY FAULT, S_TRIP FAULT, S_STOP FAULT,10.15.

S_SHUTDOWN FAULT ...........................................................................................................44

Alarm Status ..................................................................................................................4410.16.

Alarm Contacts1~10 ......................................................................................................4510.17.

C_AIR HEATER ................................................................................................................4510.18.

11. CONTROL ............................................................................................................. 46

12. PROTECTION ........................................................................................................ 47

13. SERIAL COMM ....................................................................................................... 50

14. GAIN-SET ............................................................................................................. 50

15. PROTECTION TEST ............................................................................................... 51

16. HISTORY ............................................................................................................... 51

17. Fault Items ............................................................................................................ 51

Generator Related Fault Items ..........................................................................................5117.1.

Engine Related Fault Items ...............................................................................................5217.2.

Sensor Related Fault Items ...............................................................................................5317.3.

Digital Input Related Fault ................................................................................................5417.4.

EP20 Related Alarm .........................................................................................................5417.5.

18. Comm Protocol- MODBUS .................................................................................... 57

MODBUS PROTOCOL .......................................................................................................5718.1.

GIMAC-II Plus PROTOCOL ................................................................................................6118.2.

19. Inverse Characteristics Curve ................................................................................ 63

REV. N

NeoGCP i7 PLUS+

- 9 -

1. NeoGCP i7

NeoGCP i71.1.

- Neo Generator Control Panel i7 (NeoGCP i7) is a digital type controller that uses microprocessor for

single operating generators.

Special Features1.2.

- Easy and simple to set generator with 192 × 64 graphic LCD display.

- Built-in OVR, UVR, OCR, OCGR functions.

- Fast, accurate voltage and current measurement with a tolerance of 1% possible.

- [BLOCK], [MANUAL], [AUTO], [FIRE-RUN] operation possible, REAL-TIME function also lets

[SCHEDULED-RUN] possible.

- Engine and fuselage protection operation in 7 levels.

- Save and view up to 30 faults.

- Built-in RS485 Comm port, supports Modbus Protocol 04h, 05h.

- 10 Digital Input, 8 Digital Output setup possible.

Product Image

1.3.

< NeoGCP i7 PLUS+ front image >

< NeoGCP i7 PLUS+ back image>

Specification1.4.

Size (mm)

240(L)×178(W)×53.5(H)

Operating Temperature

-20 ~ 70 ℃

Weight

Approx 862 g

CT Input range

0 ~ 5 [A]

Controller power

8 ~ 32 Vdc

Generator power

Max AC 550 [Vrms]

Max power

4.8 W

Mains Sensing Method

Single-phase,

3phase, UVR

Contact

REV. N

NeoGCP i7 PLUS+

- 10 -

2. Button usage and LED Lighting Status

Button usage2.1.

- Adjustment and setup of various operation information possible with buttons on the front.

ITEM

DESCRIPTION

DIRECTION

BUTTON

- Use to select generator information on Main screen.

- Use to move Menu on Menu screen.

- Use to move digits or change information on Menu screen.

MODE

- Use to switch to [BLOCK], [MANUAL], [AUTO] mode.

- Use to switch from Main screen to Menu screen.

ENTER

- Use to select menu from Menu screen.

- Use to input generator information on Menu screen.

ESC

- Use to switch from Menu screen to Main screen.

- Use to cancel changes of generator information on Menu screen.

- Use to switch from Alarm check screen to Main screen without release

of Alarm.

LAMP TEST

- Use to check LED on Main screen.

ALARM

- Use to switch to Alarm check screen when Alarm occurs.

- Use to check Alarms in a sequential order when many Alarms occur.

RESET

- Use to release Alarm

- Use to close breaker in [MANUAL] mode.

OPEN

- Use to open breaker in [MANUAL] mode.

START

- Use to start generator in [MANUAL] mode.

STOP

- Use to stop generator in [MANUAL] mode.

LED Lighting Status2.2.

- LED indicates status of various operation and faults, whether breaker is open or closed.

ITEM

COLOR

DESCRIPTION

BLOCK

Yellow

Lit in [BLOCK] mode

MANUAL

Yellow

Lit in [MANUAL] mode

AUTO

Yellow

Lit in [AUTO] mode

GRID ON

Red

Lit in Mains On, off in Mains Off

ALARM

Red

Lit in Alarm condition, off when Alarm is released

Red

Lit in [BREAKER CLOSE], Off in [BREAKER OPEN]

OPEN

Green

Lit in [BREAKER OPEN], Off in [BREAKER CLOSE]

START

Yellow

Off in [STOP]

Indice

Altri manuali ICD Accessori per computer

ICD

ICD AdSpeed Manuale utente

ICD

ICD Rambo XL Manuale utente

Manuali Accessori per computer popolari di altre marche

Motorola

Motorola ATRIX Manuale utente

HP USB Media Docking Station Manuale utente

Cherry

Cherry B.UNLIMITED 3.0 Manuale utente

Logitech

Logitech IO2 Manuale utente

ARM

ARM DSTREAM-ST Manuale utente

Bartec

Bartec TC 7 Series Manuale utente

Philips

Philips SPC3540 Manuale utente

Logitech

Logitech mk220 Manuale utente

SilverStone

SilverStone LC02 Manuale utente

Flexispot

Flexispot ML2B Manuale utente

Hamlet

Hamlet UNIVERSAL COVER 101 KBT2 Manuale utente

Adam Equipment

Adam Equipment RS-485 Manuale utente

Vivo

Vivo MOUNT-KB05-4DW Manuale utente

Kvaser

Kvaser Memorator Professional Manuale utente

DRC

DRC D-Imaging Manuale utente

Sven

Sven Base 305 сombo Manuale utente

Hama

Hama 108310 Manuale utente

SpeechWare

SpeechWare FlexyMike FMK03 Manuale utente