Ice Qube QD-ENG-68 Manuale di istruzioni

QD-ENG-68 Rev0 7/12/16 - 1 -

QD-ENG-68

Controller for Thermoelectric Thermal Management

INSTALLING THE CONTROLLER

The Ice Qube TMS controller is shipped complete with mounting hardware and electrical cables for easy installation. Cables

include a power cable for connecting to VDC power supply, VDC power and controller function cables for connecting the

controller to the thermoelectric thermal management system.

NOTE: Installation should be done by a qualified technician. All electrical connections should be made with

circuits de-energized. Check local codes or with authority having jurisdiction.

1. Determine a location for

the controller. See drawing for

mounting hole dimensions and

requirements. Check that cable

length is sufficient to interface

with power supply and

thermoelectric unit.

2. Route the DC power

cable and controller cable

exiting from the bottom of the

controller to the thermoelectric

unit. Insert the cable connectors

into the mating connector on the

thermoelectric unit. Check the

connectors are secure.

3. Insert the power cable

connector (shipped loose) into

the DC power interface on the

front of the controller. Route the

power cable to Class 2 DC

power supply. Check that the

power supply is properly

grounded and of sufficient

capacity to meet the power

requirements of the

thermoelectric unit. See model

specifications or label for

electrical power requirements.

Connect the wires labeled

positive, negative and ground

(PE) to the corresponding

terminals on the power supply.

Check that all connections are

proper and secure.

Figure 1. Controller Mounting (not to scale)

QD-ENG-68 Rev0 7/12/16 - 2 -

OPERATING THE CONTROLLER

1. When connected to power the temperature controller’s version number (1.20 or later) will be shown on the LCD display

for two seconds.

2. Next, the system will now test the temperature sensors. There are two temperature sensors in Ice Qube TMS: The

temperature sensor A is located in the internal return air section and measures the enclosure air temperature; and

temperature sensor B. Sensor B is not used for this application. If sensor A is abnormal, the controller will display

+ + +‘---’; if sensor B is abnormal, it shows + + +‘---’ and the audible alarm will also be activated.

3. If temperature sensors pass the test, fan testing will follow. The fans in the Ice Qube TMS are numbered as follows:

1: Internal Fan 1

3: External Fan 1

NOTE: Depending on the product model, the number of operating internal and external fans may vary. Detection

only works for the operating fans for each specific model.

If the fan speed is abnormal, the controller will display and and the audible alarm will be activated.

NOTE: If the fans do not pass the test, the detection will stop with an alarm. Press any button to exit self-detection.

The initial test procedure will take less than 60 seconds and varies based on the number of fans in the unit. After the initial

test procedure, the TMS will start its normal operation. The internal circulation fan(s) will start to operate. This fan will run

continuously so that the controller can monitor the enclosure’s internal temperature. The enclosure temperature will be

displayed on the face of the controller. When the temperature inside the enclosure is higher than the factory setting 80°F

(27°C), will be displayed. This signifies that the cooling system has begun operation to remove heat and from the

enclosure. The system may take 20 to 30 minutes before it reaches full capacity.

If the heat load within the enclosure is less than the cooling capacity of the cooling system, the temperature on the digital

display will begin to decrease. When the temperature inside the enclosure decreases 7 degrees Fahrenheit below the

“Cooling on” set point, the outside fan(s) will cycle off. The cool air fan(s) will continue to operate at low speed, circulating

air within the enclosure. The controller has a factory programmed 7 degrees Fahrenheit (4 degrees Celsius) cooling

differential. Example: “Cooling on” @ 80°F (27°C); “Cooling off” @ 73°F (23°C).

The cooling capacity of the Ice Qube TMS can be adjusted through the fan speed. The external fan speed is at its lowest

when the temperature inside the enclosure is equal to the Cool-on set point (80°F per factory settings) and reaches its

maximum when the temperature inside the enclosure reaches the factory setting of 98°F. The system reaches its largest

cooling capacity when fan(s) operate at their highest speed. Refer to "Programming the Controller". When the temperature

inside the enclosure is in the 80°F (27°C) to 98°F (37°C) range, the external fan speed will be in a linear relationship with

the enclosure temperature.

The internal circulating fan speed also changes with the enclosure temperature. The fan will be at its full speed when the

cooling starts or heating starts. When cooling or heating is not required, the internal fan will operate at low speed. The

controller monitors the fan speeds and if anything abnormal is observed regarding the fan speeds, two icons and

will appear on the controller display.

The Ice Qube TMS also offers a heating feature. If the enclosure temperature is below the factory heating set point of 50ºF

(10°C), the heat status icon will be shown on the controller display. This indicates the heat circuit has been energized

and is providing heat to the enclosure. When the temperature of the enclosure rises 7 degrees Fahrenheit (4 degrees

Celsius) above the set point, the controller will cycle the heater circuit off.

NOTE: Review the cooling and heating set points to assure both cooing and heating modes will not be

active simultaneously. A minimum of 8 deg. F is required between the cooling start temperature and the

heating start temperature.

QD-ENG-68 Rev0 7/12/16 - 3 -

PROGRAMMING THE CONTROLLER:

The digital controller has many function settings that may or may not be required for your application. However, the controller

has been set at the factory with typical default settings for immediate system operation. Please review the following default

settings.

Cooling Start Temperature 80ºF (27°C)

Heating Start Temperature 50ºF (10°C)

High Temperature Alarm 100ºF (38°C)

Low Temperature Alarm 40ºF (4°C)

Full Speed Temperature 98ºF (37°C)

Visual Alarm “ON”

Audible Alarm “ON”

Default Temperature Unit Fahrenheit

User Pin code Setting “+” “–“ “Select” “Exit” (1,2,3,4)

Filter Maintenance Alarm 0 days-disabled

CommunicationAddress 1 (not used)

To change the controller settings, please follow the sequence below to enter the pin code 1234 into the program modification:

“+” 1

“-” 2

“Select” 3

“Exit” 4

Figure 2: Digital Tap Sensitive Controller

After entering the above sequence, three alternating flashing boxes should be shown on the display face, indicating the

code was accepted. If no selection is made within one minute, the system returns to the normal operating mode.

NOTE: If entering the PIN code fails the first time, please wait until the key icon disappears and then enter the pin code again.

Press “Exit” to go back to normal mode from the controller programming mode.

Press the “SELECT” button to continue programming. and icons indicate the 'cooling on' set point is shown on the

controller display. The cooling system will begin operation at this temperature and will remain operating until the enclosure

temperature decreases approximately seven degrees Fahrenheit (four degrees Celsius) below the cooling on set point.

Press the “+” or “-” button until the desired set point is displayed. The range for this adjustment is 70° to 126°F, (21° to

52°C).

Press the “SELECT” button to continue programming. When and is displayed on the screen, it indicates the 'heating

on' setting. The heating system will begin operation at this temperature and remain operating until the enclosure temperature

increases approximately seven degrees Fahrenheit (four degrees Celsius) above the 'heating on' set point. Press the “+”

or “-” until the desired set point is displayed within a range of -22°F to 68°F (-30°C to +20°C).

NOTE: Review alarm settings if the ‘cool on’ or ‘heat on’ set points have been changed.

Press “SELECT” to continue programming. and icons appearing on the screen indicate the setting for high

temperature alarm set point. The alarm will activate at this temperature and will automatically reset at two

degrees Fahrenheit (one degree Celsius) below this temperature. Press the “+” or “-” button to change the

alarm set point within a range of 7ºF (or 4ºC) above the 'cooling on' set point, to 140°F (60°C).

QD-ENG-68 Rev0 7/12/16 4

Press “SELECT” to continue the setting. and icons appear on the screen, indicating the setting for low

temperature alarm. The alarm will activate at this temperature and will automatically reset at two degrees Fahrenheit (or

one degree Celsius) above this temperature. Press the “+” or “-” button to change the alarm setpoint within a range of -

31ºF (-35ºC) to 7º F (4ºC) below the 'heating on' set point.

Press “SELECT” to continue the setting. When and appears on the screen, the display will show the temperature at

which all fans will be running at full speed. Press the “+” or “-“ key pads to change the high speed set point within a range

from the ‘cooling on set point’ to 72°F (30°C) above ‘cooling on set point’.

Press “SELECT” to enter the alarm function setting. The screen shows the current status of the alarm. When “off” is shown

on the screen, all the alarm functions will stop. Press “+” or “-” to change the alarm switches accordingly. If the “OFF” mode

is selected, no alarms will activate and the audible on/off select function is skipped.

Press “SELECT” to enter the audible alarm setting. When or is lit, “on” or “off” will appear accordingly on the LCD

screen to show the status of the audible alarm. Press “+” or “-” to toggle the mode as desired.

Press “SELECT” to enter the temperature unit setting. Press “+” or “-” to select the desired temperature unit of Fahrenheit

or Celsius.

Press “SELECT” to continue. The display shows “PIN”. If you need to set a new pin code, press “+” on the key pad.

When “0” shows on the screen, the controller is ready to accept the new pin code. Use the keys “+”, “-”, “SELECT” and

“EXIT” to reset a new 4-digit pin code. (The four keys can be set as pin code in any order). When the first key is pressed

on the key pad, the controller display shows -1-, indicating the first digit of the pin code has been entered. Numbers -2-, -

3-, and -4- are displayed sequentially after pressing the other keys. When the fourth-digit of the pin code is entered, the

controller will move on to the next step of the programming. If the fourth pin code is not entered within 60 seconds, the

system will log out automatically. The pin code setting fails and the system will continue to use the previous pin code.

*** CAUTION***

Always record the selection sequence (PIN code) and store in a secure place.

Press "SELECT” to continue. The and icons are displayed and the filter maintenance reminder setting is shown.

Press “+” or “-” to change the alarm setting. Its setting range is 0-180 days. Programming 0 days will disable the alarm.

NOTE: The required number of days to set this alarm will be determined by the ambient air conditions. The

filter alarm should be set to “0” to disable the filter alarm for systems that do not have a filter.

Press “SELECT” to enter the communication address setting. The LCD screen is will show the current communication

address. Press “+” or “-” to change the address value within range of 1-255. The factory setting of the communication

address is 1. This function is not available for certain models.

Programming of the controller is now complete. Press the “SELECT” button to review all of the settings. Press the

“EXIT” button to enter the selected settings and to return to the normal operating mode.

NOTE: If “EXIT: button is not pressed, any changes to the program will NOT be saved.

Recovering the Factory Settings

In order to recover the default factory settings in the controller, press 442213 under the normal operation condition. When

the LCD screen shows “---” for 3 seconds, the controller restarts. Then the controller parameters are set back to factory

default settings.

QD-ENG-68 Rev0 7/12/16 5

ALARM OPERATION:

1. The enclosure temperature is above or below the alarm set point:

The display flashes, + + or + + icons will also flash with the display and the audible alarm

sounds (if activated). The enclosure temperature must rise or fall by 2°F (1°C) before the alarm resets.

2. A fan failure is detected:

The controller in the Ice Qube TMS will test its fan speeds regularly. When a fan malfunctions or its speed is over 35%

of the set range, the controller will give a fan malfunction alarm, and the

icons + + “fan No.” will appear on the screen. The fan numbers “1” and “2” refer to internal circulating fans; “3”,

“4” and “5” refer to external circulating fans; and “6” refers to the hydrogen fan. The hydrogen fan option is not available

for TEC Series.

3. The filter day timer has expired:

The display flashes showing , and the audible alarm sounds (if activated). The filter alarm can be cleared by

pressing “EXIT”. Should be disabled for these models.

4. A sensor malfunction has been detected:

+ + +“---” indicates the evaporator sensor malfunction.

Indice

Altri manuali Ice Qube Controllori

Ice Qube

Ice Qube MINI MAX Istruzioni operative

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente