icklebubba Astral Manuale utente
Astral Car Seat
Recommended
Weight
Recommended
Age
Mass Group
IMPORTANT – Read the instructions carefully before use and keep for future reference
0+0-13kg 0-12 months
(approx.)
1
2-3
4
4
5-6
6
6
7-8
9
10
10
11
12
Contents
Safety Warnings
Car Seat Features
Opening the Harness
Using the Harness
Adjusting the Shoulder Straps
Checking the Child is Correctly Fitted
Installing the Car Seat
Installing on to Pram
Adjusting the Handle Position
Fitting the Hood
Product Maintenance
Warranty
1
Contents
v.02.20
2
Safety Warnings
WARNING: Read this instruction manual carefully. Study the
illustrations in this manual closely before and during installation. Our
product is a safety product that is only safe when used according to
the instructions given in this manual. To prevent your child from falling
out of the seat, always check to make sure the carrying handle is
clicked into the carrying position before lifting the seat. Also make
sure your child is always strapped in securely with the harness belt.
WARNING: For the future use of the car seat, it is important that you
store this instruction manual.
WARNING: Never leave a child unattended in the car seat while in the
car or elsewhere.
WARNING: The correct routing of the seat belt is essential for your
child’s safety. Please see the Installation section. Never thread the belt
in any other way. When installing with the seat belt only, use the baby
car seat on a front-facing seat that has been approved according to the
ECE R16 standard or similar.
WARNING: Never use the baby car seat on a seat equipped with a
front airbag, as this can result in the death or injury of the baby. This
does not apply to the so called side airbags.
WARNING: Do not leave your baby in the car seat on a raised surface,
such as a table, work top, bed, or shopping trolley, due to the risk of
falling. Always secure your child with the harness belt, even when the
seat is not fitted in the car.
Do not leave your baby in the car seat for a long period of time. It is
important for proper motor and muscle development that you place
your baby on his stomach or back regularly.
The seat may become unsafe after an accident due to damage that is
not immediately noticeable. It should therefore be replaced.
The manufacturer can only guarantee the safety of the seat if it is used
by the original owner.
We strongly advise against using a second-hand product, as you can
never be sure of its history.
We recommend that car seats are not used for longer than 5 years
after the date of purchase. The properties of the product may
deteriorate, for example, aging of the plastic (as a result of direct
sunlight) and this may not be visible.
v.02.20
3
Safety Warnings
The moving parts of the baby car seat should not be lubricated in any way.
No alterations may be made to the baby car seat, as this could affect part or
the overall safety of the seat.
The baby car seat must not be used without its cover. Always use an original
cover, as the cover contributes to the safety of the seat.
In order to prevent damage to the cover, do not remove the logos or airbag
sticker.
Our baby car seat has been approved according to the most recent guidelines
of the ECE R 44/04: the European standard for safety seats. It is suitable for
children from birth to approximately 12 months (group 0+: 0 to 13kg).
Always check to make sure the seat fits in your car properly before
purchasing it.
The seat must always be secured, even when not in use.
An unsecured seat can injure other passengers in the car in the event of an
emergency stop.
If the seat belt height is adjustable, adjust it to the lowest position.
When installing the baby car seat on the passenger seat, position the car seat
in the rearmost position. The backrest must be in a fully upright position and
the headrest down. When not using the baby car seat, the passenger seat
(and headrest) may be adjusted as required.
Prevent damage to the seat by not wedging it between or underneath heavy
luggage, adjustable seats or slamming the car door etc.
Make sure that you properly secure all luggage and all other objects likely to
cause injury in the event of an accident.
Always cover the seat when the car is parked in the sun as plastic and, metal
parts can become very hot and the cover may become discoloured.
Always use a car seat, even for short trips, as this is when most accidents
occur.
NEVER hold a baby on your lap while driving. Due to the enormous forces
released in an accident, it will be impossible to hold onto the baby.
Never use the same seat belt to secure yourself and the child.
v.02.20
4
6. Handle
7. Sunshade/Hood
8. Shoulder Straps Slots
9. Slot for Vehicle Shoulder
Strap
10. Slot for Vehicle Lap Strap
Opening the Harness
Car Seat Features
6
7
3
4
5
1
2
10
8
9
1.Open the buckle (press the red button of the buckle);
2.Put the child into the child car seat;
3.The height of shoulder straps should be slightly higher than the child’s
shoulders (see figures on page 5)
Attention: Ensure that there is no distortion, knots or twists in straps.
1. Button for Adjusting
Handle
2. Adjuster Strap
3. Cloth Cover
4. Buckle
5. Shoulder Strap
v.02.20
5
click!
112233
4455
Using the Harness
1. Put the two buckle latches together (Figure 1)
2. Put locked latches into the safety buckle, When you hear a "click", it
means that the safety buckle has been completely locked (Figure 2)
Attention! When inserting locked latches into buckle, make sure to
hear a clear "click" noise
3. Check the harness is correctly locked by pulling the shoulder straps
upwards and downwards (Figure 3)
Attention! Shoulder belts should be securely locked with your child,
and the lap straps should be as low as possible.
4. Tighten the adjuster strap, while still keeping your child
comfortable. Loose straps are dangerous, so check the tightness with
every use (Figure 4)
Attention! The max clearance between the shoulder belt and the
child's shoulder is around one finger's width.
5. Press the slide-stopper (adjuster button) under the cloth cover and
at the same time pull the two shoulder belts upward, so that the
shoulder belts can be loosened (Figure 5)
v.02.20
6
Releasing the Harness
Checking that the child is properly fitted into the car seat
Using the Harness
incorrect-too high correct-suitable
incorrect-too low
You can release your child from the car seat by pressing the red button
on the buckle. Please make sure that the buckle latches are not catching
or hooking the child's clothes.
Adjusting the Shoulder Straps
There are 2 sets of positions for the shoulder straps. The shoulder strap
should route through the slot that is slightly higher childs shoulder
To adjust the shoulder strap, first pull out it and then route it through the
appropriate slot in the backrest of the child car seat.
The ideal position is demonstrated below:
1. The shoulder straps should be tightened to your child's body and
not cause any discomfort to your child.
2. The height of the shoulder straps are adjusted correctly.
3. There is no distortion, knots or twists in the belts.
4. The vehicle safety belt should be properly routed through the car
seat, with the latch inserted into the buckle of the vehicle.
Please follow these steps to ensure that you child is correctly fitted
into the car seat:
v.02.20
7
Installing the Car Seat
!
!
!
Seat in front
without airbag
The middle
seat in back
equipped with
3-point vehicle
belt
Rearward-facing
seat
The outer seat
in back correct
!!
!!
Side-oriented
seat
shoulder strap
lap strap
The type of vehicle belt needed:
The child seat can only be installed on the front or back seats equipped
with shoulder and lap straps.
This child car seat is only suitable when the vehicle seat is equipped
with 3-point safety belts with retractor, approved to GB 14166 or ECE R16.
correct
correct
incorrect
incorrect
v.02.20
8
Installing the Car Seat
1. Install the infant car seat rearward-facing on the vehicle seat and
ensure that it is close to the backrest of the vehicle seat (Figure 1)
2. Put the lap strap of vehicle belt across the slots in the infant car
seat and insert the latch of the vehicle belt into its buckle (Figure 2)
3. Put the shoulder strap of the vehicle seat belt across the slot in the
back of infant car seat, behind the headrest, and tighten it (Figure 3)
4. Ensure that the vehicle seatbelt is tightened and make sure that it is
not twisted or knotted. Adjust the handle to the forward placement
so that it contacts the backrest of the vehicle seat (Figure 4)
IMPORTANT: Once fitted, the vehicle seat belt and the handle of the
infant car seat cannot be located in the position shown in Figure 2. If
in doubt, consult the manufacturer.
1
3 4
2
CLICK
buckle
latch
Do not use any other connection points than those marked
WARNING！
v.02.20
9
Installing on to Pram
v.02.20
Altri manuali per Astral
2
Indice
Altri manuali icklebubba Seggiolino auto
icklebubba
icklebubba Astral Manuale utente
icklebubba
icklebubba RADIUS Manuale utente
icklebubba
icklebubba ROTATOR I-SIZE Manuale utente
icklebubba
icklebubba Mercury Manuale utente
icklebubba
icklebubba Solar Manuale utente
icklebubba
icklebubba Galaxy Manuale utente
icklebubba
icklebubba RADIUS Manuale utente
icklebubba
icklebubba ROTATOR Manuale utente
icklebubba
icklebubba RADIAL I-SIZE PLUS Manuale utente
icklebubba
icklebubba Astral Manuale utente
