ICM Controls SimpleComfort 2010 Istruzioni generali
1 Heat/1 Cool
Manual Changeover
Battery or Hardwire
SC 2010
Non-Programmable Electronic Thermostat
Installation, Operation & Application Guide
For more information on our complete range of American-made
products – plus wiring diagrams, troubleshooting tips and more,
visit us at www.icmcontrols.com
• Configurable
• Single Stage Heat/Cool Systems
• Single Stage Heat Pump Systems
• Backlit Display
• Compatible with Gas, Oil, or Electric
• Filter Check
• Status Indicator Light
• Relay Outputs
(minimum voltage drop in thermostat)
• Ideally Suited for:
– Residential (New Construction/Replacement)
– Light Commercial
Table of Contents
Parts Diagram .............................................................................................................................1
Specifications .............................................................................................................................. 2
Important Safety Information .....................................................................................................2
Package Contents/Tools Required............................................................................................... 2
To Remove Existing Thermostat ................................................................................................3
To Install Thermostat .................................................................................................................. 3
Wiring Diagrams..........................................................................................................................5
Configuration Mode...................................................................................................................10
Testing the Thermostat ............................................................................................................13
Mode of Operation ....................................................................................................................14
Troubleshooting ........................................................................................................................15
1
Parts Diagram
2
Electrical rating: • 24 VAC (18-30 VAC) • DC Power: 3.0 VDC (2 “AA” batteries included)
• 1 amp maximum per terminal • 3 amp maximum total load
Temperature control range: 45°F to 90°F (7°C to 32°C) Accuracy: ± 1°F (± 0.5°C)
System configurations: 1-stage heat, 1-stage cool, heat pump, gas, oil, electric
Timing:
Anti-short Cycle:
5 minutes
Backlight Operation: Battery for 5 seconds, hardwired for 10 seconds
Terminations: RC, RH, W, Y, B, O, G, C
Specications
WARNING!
:
Always turn off power at the main power supply before installing, cleaning, or removing
thermostat.
• This thermostat is for 24 VAC applications only; do not use on voltages over 30 VAC
• Do not short across terminals of gas valve or system control to test operation; this will damage your
thermostat and void your warranty
• All wiring must conform to local and national electrical and building codes
• Do not use air conditioning when the outdoor temperature is below 50 degrees; this can damage your
A/C system and cause personal injuries
• Use this thermostat only as described in this manual
Important Safety Information
Package includes: SimpleComfort®2010 thermostat on base, thermostat cover, wiring labels, screws and
wall anchors, Installation, Operation and Application Guide
Tools required for installation: Drill with 3/16” bit, hammer, screwdriver
Package Contents/Tools Required
3
ELECTRICAL SHOCK HAZARD
– Turn off power at the main service panel by removing the fuse
or switching the appropriate circuit breaker to the OFF position before removing the existing
thermostat.
1. Turn off power to the heating and cooling system by removing the fuse or switching the appropriate
circuit breaker off.
2. Remove cover of old thermostat. This should expose the wires.
3. Label the existing wires with the enclosed wire labels before removing wires.
4. After labeling wires, remove wires from wire terminals.
5. Remove existing thermostat base from wall.
6. Refer to the following section for instructions on how to install this thermostat.
ELECTRICAL SHOCK HAZARD
– Turn off power at the main service panel by removing the fuse
or switching the appropriate circuit breaker to the OFF position before removing the existing
thermostat.
IMPORTANT: Thermostat installation must conform to local and national building and electrical
codes and ordinances.
Note: Mount the thermostat about five feet above the floor. Do not mount the thermostat on an
outside wall, in direct sunlight, behind a door, or in an area affected by a vent or duct.
1. Turn off power to the heating and cooling system by removing the fuse or switching the appropriate
circuit breaker off.
To Install Thermostat
To Remove Existing Thermostat
4
To Install Thermostat (continued)
2. To remove cover, insert and twist a coin or screwdriver in the slots on the sides of the thermostat.
3. Put thermostat base against the wall where you plan to mount it (Be sure wires will feed through the
wire opening in the base of the thermostat).
4. Mark the placement of the mounting holes.
5. Set thermostat base and cover away from working area.
6. Using a 3/16” drill bit, drill holes in the places you have marked for mounting.
7. Use a hammer to tap supplied anchors in mounting holes.
8. Align thermostat base with mounting holes and feed the control wires through wire opening.
9. Use supplied screws to mount thermostat base to wall.
10. Insert stripped, labeled wires in matching wire terminals. See “Wiring Diagrams” section of this
manual (Page 5).
CAUTION!
:
Be sure exposed portion of wires does not touch other wires.
11. Tighten screws on terminal block. Gently tug wire to be sure of proper connection. Double check that
each wire is connected to the proper terminal.
12. Seal hole for wires behind thermostat with non-flammable insulation or putty, or use an ICM insulated
wall plate (ACC-WP01).
13. Set the Gas/Electric swith to electric or gas/oil.
14. Install two “AA” alkaline batteries (if required per wiring diagrams on Pages 5-9) in the thermostat
oriented in the direction shown on the battery holder.
15. Replace cover on thermostat by snapping it in place.
16. Turn on power to the system at the main service panel.
17. Test thermostat operation as described in “Testing the Thermostat” (Page 13).
5
Battery Powered
2-Wire, Single Transformer
Note: Batteries required.
Battery Powered
3-Wire, Single Transformer
Note: Batteries required.
Wiring Diagrams
6
Hardwired
3-Wire, Single Transformer
Note: Batteries (optional) will work as a
backup during power outages.
Hardwired
4-Wire, Single Transformer
Note: Batteries (optional) will work as a
backup during power outages.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali ICM Controls Termostato
ICM Controls
ICM Controls SC1600L Istruzioni generali
ICM Controls
ICM Controls SC 3201 Istruzioni generali
ICM Controls
ICM Controls SC 4211 Istruzioni generali
ICM Controls
ICM Controls SC 2000 Istruzioni generali
ICM Controls
ICM Controls SC3000L Manuale utente
ICM Controls
ICM Controls SC 2001 Istruzioni generali
ICM Controls
ICM Controls SC4011 Istruzioni generali
ICM Controls
ICM Controls SC2010 N Istruzioni generali
ICM Controls
ICM Controls ICM I3 Istruzioni per l'installazione e il funzionamento
ICM Controls
ICM Controls SC4812 Manuale utente
ICM Controls
ICM Controls SC 3801 Manuale utente
ICM Controls
ICM Controls SC2201 Istruzioni generali
ICM Controls
ICM Controls SC1600L Manuale utente
ICM Controls
ICM Controls I3 1010HR Istruzioni generali
ICM Controls
ICM Controls SC2000L Istruzioni generali
ICM Controls
ICM Controls Single Comfort SC2010L Manuale utente
ICM Controls
ICM Controls SC1600L/VL Manuale utente
ICM Controls
ICM Controls SC 2311 Istruzioni generali
ICM Controls
ICM Controls FS1500L Istruzioni generali
ICM Controls
ICM Controls i3 2010WR Istruzioni generali
