Icom Ic-2730A Manuale del proprietario

Altri manuali per ic-2730A

2

Indice

Manuali Ricetrasmettitore popolari di altre marche

Yaesu

Yaesu FT-7B Manuale utente

Kenwood

Kenwood ProTalk TK-3201 Manuale utente

Texas Instruments

Texas Instruments TLK10232 Manuale utente

Mizuho

Mizuho MX-2 Guida del prodotto

Kenwood

Kenwood TK-3180 Manuale operativo e di manutenzione

Blitz

Blitz MJ-398U Manuale utente

Utilicom

Utilicom LongRanger 2050 Manuale utente

Standart

Standart HX290UKA Manuale utente

Altronix

Altronix Pace1PTM Manuale utente

Kirisun

Kirisun PT2208 Manuale utente

ELECRAFT

ELECRAFT KX2 Manuale utente

Zodiac

Zodiac K3 Manuale utente

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuale utente

Kenwood

Kenwood TK-2217 Manuale utente

Siemens

Siemens PSO 4000 Manuale utente

Kenwood

Kenwood TS-590SG Manuale utente

Midland

Midland G8E-BT Manuale

ComNav

ComNav Mariner X2 Manuale utente

©June 2016 Icom America Inc. Page 1

Icom America, Inc.

12421 Willows Road NE

Kirkland, WA 98034

IC-2730A Memory Channel Programming

This programming method uses the front panel keys.

What you will need:

•Operating frequency

•Offset direction (Duplex, for repeater use)

•Subaudible tone frequency for your repeater

Entering a Frequency

1. Press the Main/Band key to select the side of the display you wish to use (MAIN will appear on

the selected side).

2. Press the [V/MHz/Scan] key to place the radio in VFO mode.

3. Rotate the dial (for the side of the radio you selected) to enter your frequency.

4. Press [Menu] to enter the menu selection mode.

Selecting the Repeater Tone

1. Rotate the dial to select R TONE.

2. Press the Enter key (the key below a backwards-facing arrow: [MW]). You will see R TONE to

the left of the display and the value of the subaudible tone on the right side.

3. Rotate the dial to select the repeater tone.

4. Press the Enter key.

Turning on the Tone Encoder

Use the dial to select TONE and press the Enter key. The letter Twill appear on the display above the

frequency to show that the tone encoder is enabled.

Setting the offset (DUPLEX)

1. Press and hold the key labeled [MONI/DUP]. You will see an indication of the Duplex direction

(-, +or OFF).

2. Select the offset direction by rotating the dial.

3. When you have the correct offset direction, press the [MONI/DUP] key again.

©June 2016 Icom America Inc. Page 2

Icom America, Inc.

12421 Willows Road NE

Kirkland, WA 98034

Saving these settings to Memory

Your display should show your frequency, the duplex (DUP+or DUP-), and the Tfor tone encoder. To

save these settings to a Memory Channel, do the following:

1. Press the [MW] key.

2. MW will blink on the display.

3. Rotate your dial to display CH SEL (channel selection).

4. Press the Enter key.

5. Rotate the dial to the memory channel you wish to use.

6. Press the Enter key.

7. Rotate the dial to WRITE.

8. Press the Enter key.

9. The display will show WRITE.

10. Rotate the dial to YES.

11. Press the Enter key.

Verify the Programming

To check the memory channels, momentarily press the [MR/CALL] key and rotate the dial through the

memory channels and confirm that the repeater is programmed into the memory channel that you

selected.