Icom IC-718 Manuale di istruzioni

Altri manuali per IC-718

10

Indice

Manuali Ricetrasmettitore popolari di altre marche

Yaesu

Yaesu FT-7B Manuale utente

Kenwood

Kenwood ProTalk TK-3201 Manuale utente

Texas Instruments

Texas Instruments TLK10232 Manuale utente

Mizuho

Mizuho MX-2 Guida del prodotto

Kenwood

Kenwood TK-3180 Manuale operativo e di manutenzione

Blitz

Blitz MJ-398U Manuale utente

Utilicom

Utilicom LongRanger 2050 Manuale utente

Standart

Standart HX290UKA Manuale utente

Altronix

Altronix Pace1PTM Manuale utente

Kirisun

Kirisun PT2208 Manuale utente

ELECRAFT

ELECRAFT KX2 Manuale utente

Zodiac

Zodiac K3 Manuale utente

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuale utente

Kenwood

Kenwood TK-2217 Manuale utente

Siemens

Siemens PSO 4000 Manuale utente

Kenwood

Kenwood TS-590SG Manuale utente

Midland

Midland G8E-BT Manuale

ComNav

ComNav Mariner X2 Manuale utente

Icom IC-718 'Quickstart' Manual

May 2013

de VE7D N

Of course, at the start of an incident, we will use

conventional handwritten messaging. For this, we

use the FT-8800 dual band VHF/ HF transceiver

However, there may be a need for longer distance

communications. We supply this with the Icom

IC-718 HF Transceiver

Power up the station

- Remove front and back covers, set aside

- Verify HF transceiver is connected to a HF antenna

- Verify AC power plug is plugged into a power source

- Turn on power master

switch (back of unit)

- Turn on 12vdc power

supply

Turn on the Transceiver

- Turn on, tune the HF Transceiver ( details next slide )

Turn on Transceiver

-Press and hold 'Pwr” button (2 sec)

You have no way to know what changes may have been made and

left on the IC-718 the last time it is used.

Therefore it is important to check both the 'Quick et' and ' ettings'

[ Quick Press ] POWER button to turn on the transceiver

- Adjust volume and squelch to taste.

Assumes channel is pre programmed in memory. If not, see reference

manual

Avoid errors, accept no interruptions when performing these checklists

Verify 'Quick et' Menus

[ Quick Press ] POWER button to turn on the transceiver

[ Press & Hold ] 1sec, [ ET ] button to enter 'Quick et' mode

One uses the [ Up ] & [ Dwn ] Buttons to navigate menus

Rotate main tuning knob to adjust a setting within a menu

'Quick et' - RF Power

[ Press & Hold ] 1sec, [ ET ] button to enter 'Quick et' mode

Use the [ Up ] & [ Dwn ] Buttons to navigate to 'RF power'

Rotate main tuning knob to adjust power to anyone of 99

levels or H for the default, full power.

'Quick et' - Mic gain

[ Press & Hold ] 1sec, [ ET ] button to enter 'Quick et' mode

One uses the [ Up ] & [ Dwn ] Buttons to navigate to 'Mic gain'

Rotate main tuning knob to adjust Mic gain to anyone of 99

levels or H. Default, is 50. Adjust to suit your voice

'Quick et' - Vox gain

[ Press & Hold ] 1sec, [ ET ] button to enter 'Quick et' mode

One uses the [ Up ] & [ Dwn ] Buttons to navigate to 'Vox gain'

Rotate main tuning knob to adjust Vox gain to anyone of 99

levels or H. Default, is 50. Adjust to suit your voice

'Quick et' - Vox delay

[ Press & Hold ] 1sec, [ ET ] button to enter 'Quick et' mode

Use the [ Up ] & [ Dwn ] Buttons to navigate to 'Vox delay'

Rotate main tuning knob to adjust Vox delay to any delay

between 0 and 2 seconds in 0.1 increments