Icom IC-V3MR Manuale utente

INSTRUCTION MANUAL

VHF TRANSCEIVER

|V3MR

5 BATTERY CHARGING

6 OPTIONS

4 ADVANCED OPERATION

3 BASIC OPERATION

2 PANEL DESCRIPTION

1 ACCESSORIES

INTRODUCTION

Thank you for choosing this Icom product. This

product was designed and built with Icom’s state of

the art technology and craftsmanship. With proper

care, this product should provide you with years of

trouble-free operation.

IMPORTANT

FIRST, CAREFULLY READ INSTRUCTIONS that is

provided with the transceiver.

READ ALL INSTRUCTIONS carefully and completely

before using the transceiver.

SAVE THIS INSTRUCTION MANUAL— This

instruction manual contains important operating

instructions for the IC-V3MR.

EXPLICIT DEFINITIONS

WORD DEFINITION

RDANGER! Personal death, serious injury or an

explosion may occur.

RWARNING! Personal injury, fire hazard or electric

shock may occur.

CAUTION Equipment damage may occur.

NOTE

If disregarded, inconvenience only.

No risk of personal injury, fire or

electric shock.

Icom, Icom Inc. and the Icom logo are registered

trademarks of Icom Incorporated (Japan) in Japan,

the United States, the United Kingdom, Germany,

France, Spain, Russia, Australia, New Zealand, and/or

other countries.

All other products or brands are registered trademarks

or trademarks of their respective holders.

Icom is not responsible for the destruction, damage

to, or performance of any Icom or non-Icom

equipment, if the malfunction is because of:

• Force majeure, including, but not limited to, fires,

earthquakes, storms, floods, lightning, other

natural disasters, disturbances, riots, war, or

radioactive contamination.

• The use of Icom transceivers with any equipment

that is not manufactured or approved by Icom.

INTRODUCTION

RDANGER! NEVER operate the transceiver near

unshielded electrical blasting caps or in an explosive

atmosphere. This could cause an explosion and

death.

RWARNING! NEVER use or charge Icom battery

packs with non-Icom transceivers or non-Icom

chargers. Only Icom battery packs are tested and

approved for use with Icom transceivers or charged

with Icom chargers. Using third-party or counterfeit

battery packs or chargers may cause smoke, fire, or

cause the battery to burst.

RWARNING! NEVER hold the transceiver so that

the antenna is very close to, or touching exposed

parts of the body, especially the face or eyes, while

transmitting.

RWARNING! NEVER operate the transceiver with

earphones, a headset, or other audio accessories

at high volume levels. The continuous high volume

operation may cause a ringing in your ears. If you

experience the ringing in your ears, reduce a volume

level or discontinue use.

CAUTION: DO NOT use or leave the transceiver in

excessively dusty environments. This could damage

the transceiver.

CAUTION: DO NOT short the terminals of the battery

pack. Shorting may occur if the terminals touch metal

objects such as a key, so be careful when placing the

battery packs (or the transceiver) in bags, and so on.

Carry them so that shorting cannot occur with metal

objects. Shorting may damage not only the battery

pack but also the transceiver.

CAUTION: DO NOT change the internal settings

of the equipment. This may reduce equipment

performance and/or cause extensive and expensive

damage to the equipment. The equipment warranty

does not cover any problems caused by unauthorized

internal adjustments.

CAUTION: DO NOT operate the transceiver unless

the flexible antenna, battery pack, and jack cover

are securely attached to the transceiver and that the

antenna and battery pack are dry before attachment.

Exposing the inside of the transceiver to dust or water

will result in serious damage to the transceiver.

CAUTION: DO NOT operate the transceiver while

driving a vehicle. Safe driving requires your full

attention—anything less may result in an accident.

CAUTION: DO NOT use harsh solvents such as

Benzine or alcohol when cleaning. This could damage

the equipment surfaces. If the surface becomes dusty

or dirty, wipe it clean with a soft, dry cloth.

NOTE: DO NOT use or leave the transceiver in areas

with temperatures below –30°C (–22°F) or above

+60°C (+140°F), or in areas subject to direct sunlight,

such as the dashboard.

DO NOT push PTT unless you actually intend to

transmit.

KEEP the transceiver away from heavy rain and

never immerse it in water. The transceiver meets

IP54* requirements for dust-protection and splash

resistance.

However, once the transceiver has been dropped,

dust-protection and splash resistance cannot be

guaranteed due to the fact that the transceiver may be

cracked or the waterproof seal damaged, and so on.

* Only when the battery pack and jack cover are

attached.

NEVER place the transceiver in an insecure place to

avoid inadvertent use by unauthorized persons.

BE CAREFUL! The transceiver may become hot after

continuously transmitting for long periods of time.

Even when the transceiver power is OFF, a slight

current still flows in the circuits. Remove the battery

pack from the transceiver when not using it for a long

time. Otherwise, the installed battery pack or batteries

will become exhausted, and will need to be recharged

or replaced.

PRECAUTIONS

iii

INTRODUCTION

Your Icom radio generates RF

electromagnetic energy while transmitting.

This radio is designed for and classified as

for “Occupational Use Only.” This means

it must be used only during the course of

employment by individuals aware of the hazards, and

the ways to minimize such hazards. This radio is NOT

intended for use by the “General Population” in an

uncontrolled environment.

This radio has been tested and complies with the FCC

RF exposure limits for “Occupational Use Only.” In

addition, your Icom radio complies with the following

Standards and Guidelines with regard to RF energy

and electromagnetic energy levels and evaluation of

such levels for exposure to humans:

• FCC KDB Publication 447498 D03, Evaluating

Compliance with FCC Guidelines for Human

Exposure to Radio Frequency Electromagnetic

Fields.

• American National Standards Institute (C95.1-

2019), IEEE Standard for Safety Levels with

Respect to Human Exposure to Radio Frequency

Electromagnetic Fields, 0 Hz to 300 GHz.

• American National Standards Institute (C95.3-

2002), IEEE Recommended Practice for

the Measurement of Potentially Hazardous

Electromagnetic Fields– RF and Microwave.

• The antenna, battery, belt clip, speaker-

microphone, and other accessories that are

listed in “OPTIONS” on this instruction manual,

are authorized for use with this product. Use

of accessories other than those specified may

result in RF exposure levels exceeding the FCC

requirements for wireless RF exposure.

To ensure that your expose to RF

electromagnetic energy is within the FCC

allowable limits for occupational use,

always adhere to the following guidelines:

• DO NOT operate the radio without a proper

antenna attached, as this may damage the radio

and may also cause you to exceed FCC RF

exposure limits. A proper antenna is the antenna

supplied with this radio by the manufacturer or an

antenna specifically authorized by the manufacturer

for use with this radio.

• DO NOT transmit for more than 50% of the total

radio use time (“50% duty cycle”). Transmitting

more than 50% of the time can cause FCC RF

exposure compliance requirements to be exceeded.

The radio is transmitting when the status indicator

lights red. You can cause the radio to transmit by

pushing the “PTT” switch.

• ALWAYS keep the antenna at least 2.5 cm (1 inch)

away from the body when transmitting, and only

use the Icom belt-clip listed in “OPTIONS” on this

instruction manual when attaching the radio to your

belt, or other place, to ensure FCC RF exposure

compliance requirements are not exceeded.

The information listed above provides the user with

the information needed to make him or her aware of

RF exposure, and what to do to assure that this radio

operates within the FCC RF exposure limits of this

radio.

Electromagnetic Interference/Compatibility

During transmissions, your Icom radio generates RF

energy that can possibly cause interference with other

devices or systems. To avoid such interference, turn

OFF the radio in areas where signs are posted to

do so. DO NOT operate the transmitter in areas that

are sensitive to electromagnetic radiation such as

hospitals, aircraft, and blasting sites.

Occupational/Controlled Use

The radio transmitter is used in situations in which

persons are exposed as a consequence of their

employment, provided those persons are fully aware

of the potential for exposure and can exercise control

over their exposure.

CAUTIO N

WARNING

SAFETY TRAINING INFORMATION

INTRODUCTION

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment

off and on, the user is encouraged to try to correct

the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment

and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV

technician for help.

CAUTION: Changes or modifications to this

transceiver, not expressly approved by Icom Inc.,

could void your authority to operate this transceiver

under FCC regulations.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the condition that this device

does not cause harmful interference.

• DO NOT operate or adjust all controls,

adjustments, and switches without resulting in a

violation of the FCC rules.

• DO NOT replace any transmitter components

such as crystal, semiconductor, and so on. It could

result in a violation of the FCC rules.

Adjustment of this radio should be performed by or

under the immediate supervision and responsibility

of Icom Inc. or:

• A person certified as technically qualified to

perform transmitter maintenance and repair duties

in the private land mobile services.

• Services by an organization or committee

representative of the private land mobile services

user.

• Since FCC Part 95.2725 requires monitoring the

channel before transmit, Lock-out (Busy lockout)

must be enabled if Moni (Monitor) button was

disabled.

FCC INFORMATION

1-1

Section 1ACCESSORIES

Supplied accessories ��1-2

Belt clip��1-2

Flexible antenna ��1-2

Battery pack ��1-3

Jack cover ��1-3

1ACCESSORIES

1-2

Supplied accessories

Battery pack

(BP-298)

Battery charger

(BC-240)

Belt clip

(MB-124)

Flexible antenna

(FA-SC28V)

Jack cover

(with screws)

Power adapter

(BC-242)

NOTE: Some accessories may not be supplied, or

the shape may differ, depending on the transceiver

version�

Belt clip

Attaching:

1� Remove the battery pack from the transceiver if it

is attached�

2� Slide the belt clip in the direction of the arrow until

the belt clip is locked and makes a ‘click’ sound�

Belt clip

Battery pack

Detaching:

zLift the tab up (1), and slide the belt clip in the

direction of the arrow (2)�

Tab

BE CAREFUL! DO NOT break your fingernail�

Flexible antenna

Connect the antenna to the antenna connector�

CAUTION:

• DO NOT carry the transceiver by holding only the

antenna�

• DO NOT connect an antenna other than the

specified antenna�

• DO NOT transmit without an antenna�

1ACCESSORIES

1-3

Jack cover

Attach the jack cover when optional equipment is not

used�

Attaching:

1� Attach the jack cover to the [SP MIC] jack (1)�

2� Tighten the screws (2)�

Detaching:

1� Remove the screws with a Phillips screwdriver

(1)�

2� Detach the jack cover to connect the optional

equipment (2)�

Battery pack

Attaching:

1� Insert the battery pack in the direction of the arrow

(1), and then close it�

2� Hook the latch until it makes a ‘click’ sound (2)�

Battery pack

Latch

Detaching:

RWARNING! The latch is tightly locked, so use

caution when releasing it� DO NOT use your

fingernail� Use the edge of a coin or screwdriver tip

to carefully release it�

zUnhook the latch (1), and then lift up the battery

pack in the direction of the arrow (2)�

CAUTION: NEVER remove or attach the battery

pack when the transceiver is wet or soiled� This may

result in water or dust getting into the transceiver

or the battery pack, and may result in them being

damaged�

NOTE: Keep battery terminals clean� It’s a good idea

to occasionally clean them�

2-1

Section 2PANEL DESCRIPTION

Front, top and side panels��2-2

DStatus indicator ��2-2

DSpeaker microphone jack��2-2

DAbout the Software Key functions ��2-2

Status indicator��2-3

Assignable Software Key functions ��2-4

2PANEL DESCRIPTION

2-2

Front, top and side panels

DStatus indicator

• Lights red: Transmitting�

• Lights green:

Receiving or squelch is open�

• Lights or blinks orange: A matching signal is

received, depending on the

presetting�

LRefer to the Status indicator section� (p� 2-3)

Status

indicator

Microphone

Speaker

microphone

jack

Speaker

[PTT]

[Upper]

[Lower]

[VOL]

Antenna

connector

[Rotary

Selector]

DSpeaker microphone jack

Connect the optional speaker microphone or VOX

adapter cable�

Jack cover

CAUTION: DO NOT use the transceiver without the

jack cover or the optional equipment attached�

The transceiver meets IP54 requirements for dust-

protection and splash resistance only when the

battery pack and jack cover are attached�

DAbout the Software Key functions

Dealers can assign Software Key functions to the

[Upper] or [Lower] keys� See page 2-4 for details�

The following Software keys are assigned to default:

Key Assigned Software

[Upper] Push to turn the Monitor function ON or

OFF�

[Lower] No function is assigned to default�

Indice

Manuali Ricetrasmettitore popolari di altre marche

Yaesu

Yaesu FT-7B Manuale utente

Kenwood

Kenwood ProTalk TK-3201 Manuale utente

Texas Instruments

Texas Instruments TLK10232 Manuale utente

Mizuho

Mizuho MX-2 Guida del prodotto

Kenwood

Kenwood TK-3180 Manuale operativo e di manutenzione

Blitz

Blitz MJ-398U Manuale utente

Utilicom

Utilicom LongRanger 2050 Manuale utente

Standart

Standart HX290UKA Manuale utente

Altronix

Altronix Pace1PTM Manuale utente

Kirisun

Kirisun PT2208 Manuale utente

ELECRAFT

ELECRAFT KX2 Manuale utente

Zodiac

Zodiac K3 Manuale utente

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuale utente

Kenwood

Kenwood TK-2217 Manuale utente

Siemens

Siemens PSO 4000 Manuale utente

Kenwood

Kenwood TS-590SG Manuale utente

Midland

Midland G8E-BT Manuale

ComNav

ComNav Mariner X2 Manuale utente