Iddero HC2-KNX Foglio di istruzioni

www.iddero.com 120719-02

IDDERO TOUCH PANELS

Video door phone configuration

www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration

TABLE OF CONTENTS

1INTRODUCTION............................................................................................................................... 3

2INSTALLATION................................................................................................................................ 3

3INITIAL CONFIGURATION.............................................................................................................. 4

42N HELIOS IP VIDEO DOOR PHONES .......................................................................................... 5

4.1 Supported models ................................................................................................................. 5

4.2 Video door phone configuration ............................................................................................ 5

5MOBOTIX VIDEO DOOR PHONES............................................................................................... 11

5.1 Supported models ............................................................................................................... 11

5.2 Video door phone configuration .......................................................................................... 11

6ROBIN TELECOM VIDEO DOOR PHONES ................................................................................. 22

6.1 Supported models ............................................................................................................... 22

6.2 Video door phone configuration .......................................................................................... 22

7IDDERO TOUCH PANEL CONFIGURATION ............................................................................... 28

All other registered trademarks and trade names used in this document are the property of their respective owners. Other product and/or

company names used in this document may be protected by copyrights, trademarks, or patents.

www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration

1 INTRODUCTION

The HC2-KNX 7” and HC2L-KNX 10,4” touch panels from Iddero can be used as indoor monitors for

compatible video door phone systems. This document provides the necessary information to configure

this functionality.

2 INSTALLATION

The HC2-KNX and HC2L-KNX touch panels support IP-based door phone systems. In order to

interconnect the video door phone system and an Iddero touch panel, only a TCP/IP network

connection is required.

The following figure shows a typical configuration where the door phone system and the Iddero touch

panels are connected to different ports of an Ethernet switch, using standard UTP cable. Category

CAT5E or better is recommended.

On single-home setups where only one touch panel is used and a local data network is not required,

the Ethernet switch can be skipped by directly connecting the video door phone system and the touch

panel through a crossover Ethernet cable. However, using an Ethernet switch is recommended in

order to allow for future expansion of the installation.

Video door phone

Ethernet switch

Iddero

touch panels

www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration

3 INITIAL CONFIGURATION

In order to use the video door phone function of the HC2-KNX / HC2L-KNX touch panel, you must first

enable it in the Iddero configuration software.

Before proceeding, please make sure you have selected “HC2-KNX” or “HC2L-KNX” in the “System

type” field of the “Project” section.

Then, please go to the “Video door phone” section, tick the “Video door phone enabled” checkbox,

and select the type of video door phone system to use from the “Type” drop-down list.

Depending on the selected video door phone type, additional options may appear.

)Remember:

The video door phone function is not supported on the HC1-KNX touch panel. If this function appears to

be disabled and you cannot enable it, go back to the “Project” section and double-check that you have

selected “HC2-KNX” or “HC2L-KNX” in the “System type” field.

www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration

4 2N HELIOS IP VIDEO DOOR PHONES

4.1 Supported models

All 2N Helios IP door communicators (Vario, Force, and Safety series) are supported.

Two-way audio and the door opening function are implemented for all supported 2N Helios IP models.

Visualization of video input in the HC2-KNX touch panel is supported for camera-equipped 2N Helios

IP door communicators.

In the Iddero configuration software, select “2N Helios IP Pro” if your Helios door communicator is

equipped with a 2N professional license key (manufacturer part number 9137901). This enables some

special features such as the ability to open the door without requiring an incoming call, as well as an

enhanced video encoding scheme that provides better video quality.

If your Helios door communicator is not equipped with a professional license key, please select “2N

Helios IP Basic” instead (requires version 1.6.1 or later of the Iddero configuration software).

For more information about Helios IP door communicators, please check the manufacturer’s website:

http://www.2n.cz/en/

4.2 Video door phone configuration

This section provides enough information to configure 2N Helios IP video door phone systems for use

in combination with Iddero touch panels. This information is provided for illustrative purposes only. For

additional details, or for advanced configuration of the 2N Helios IP product, please refer to the

documentation provided by 2N.

Configuration of the video door phone requires the following steps:

1. Network configuration

2. Video configuration (for camera-equipped door stations)

3. Doorbell button configuration

4. Door opening function configuration

www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration

1. Network configuration

2N Helios IP door stations are preconfigured to obtain an IP address dynamically, using the DHCP

protocol. You will need to modify the network configuration and assign a static IP address to the unit.

In order to do this, access the door phone’s web-based administration interface through a standard

web browser, and follow these steps:

•Enter the Advanced Settings →Network menu.

•Disable DHCP mode (“DHCP client enabled: No”)

•Enter an IP address and network mask in the “Static IP address” y “Network mask” fields of

the “Static settings” section.

•Click on the save icon in the bottom right corner (floppy disk icon)

Please make sure that the IP address assigned to the 2N Helios IP video door phone can be reached

from the Iddero touch panel. For this, both devices must be in the same TCP/IP subnet. For example,

if the touch panel’s IP address is 192.168.0.200, with subnet mask 255.255.255.0 (default values),

assign an IP in the 192.168.0.x range to the video door phone (for example, 192.168.0.231), and set

the subnet mask as 255.255.255.0.

)Remember:

You can check the current TCP/IP configuration of the Iddero panel at anytime by going to the System

Settings menu and pressing the “Network” button. The network configuration is also shown onscreen

when the touch panel boots in installation mode.

www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration

2. Video configuration

Enter the Advanced Settings →Streaming menu and proceed as follows:

a) For door phone stations equipped with a professional license (2N Helios IP Pro):

•Make sure the RTSP service is enabled (select “RTSP Server: On”)

•In the “Video codec settings” section, select “Video codec: H.264/MPEG-4 AVC”

•The following configuration recommended for optimal results:

oVideo resolution: CIF (352x288)

oFrame rate: 30 fps

oVideo bitrate: 1024 kbps

•Click on the save icon in the bottom right corner

b) For door phone stations not equipped with a professional license (2N Helios IP Basic):

•Make sure JPEG video streaming is enabled (select “Anonymous access: Yes” in the JPEG

video settings section)

•Click on the save icon in the bottom right corner

www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration

3. Doorbell button configuration

Now we need to configure the call actions associated to each button in the video door phone.

For example, to configure the call action for quick dialling button 1 in the video door phone, proceed as

follows:

•Enter the Basic Settings →Phone book menu

•Select position “1” in the upper part f the screen. Position 1 corresponds to quick dialling

button 1 in the video door phone.

•Ensure that this position is enabled (“Position enabled: Yes”)

•Ensure that this user is active (“User current state: Active”)

•Enter the SIP address of the Iddero touch panel in the “Number 1” field of the “Phone

numbers” section. The SIP address has the following syntax (replace <ip_address> with the

actual IP address of the Iddero touch panel):

sip:hc2@<ip_address>

•Click on the save icon in the bottom right corner

Repeat this process if you want to configure additional buttons in the video door phone.

www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration

4. Door opening function configuration

On Helios IP video door phones equipped with professional licenses, the door opening function can be

configured to operate over HTTP. This allows opening the door from the touch panel even if there is

no incoming call. If this option is not enabled, the door can only be opened once an incoming call has

been accepted.

a) Door opening function through HTTP (only available for 2N Helios IP Pro):

•Enable door opening through HTTP:

oEnter the Advanced Settings →Miscellaneous menu

oSelect: “Enable switch control by http: Yes”

oClick on the save icon in the bottom right corner

•Configure the switch:

oEnter the Basic Settings →Switch 1 menu

oSet “Switch mode” to “Monostable”

oClick on the save icon in the bottom right corner

•If a second door exists in the building, repeat the above step in Basic Settings →Switch 2

www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration

b) Door opening function through SIP:

•First, verify that DTMF code reception is enabled:

oEnter the Advanced Settings →Audio Codecs menu

oMake sure that the “Receive via RTP” and “Receive via SIP” parameters are enabled.

If they aren’t, enable them and click on the save icon in the bottom right corner.

•Configure the door opening code in the main door:

oEnter the Basic Settings →Switch 1 menu

oMake sure that lock control is enabled: “Switch enabled: Yes”

oEnter a door opening code. Short codes are recommended – one or two digits long;

for example, “00”.

oClick on the save icon in the bottom right corner

•If a second door exists in the building, you can also configure a door opening code for it in the

Basic Settings →Switch 2 menu.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Iddero Sistema di interfono

Iddero

Iddero Touchone Foglio di istruzioni

Manuali Sistema di interfono popolari di altre marche

Bticino

Bticino LINEA 3000 Manuale utente

MSI

MSI MSI-140 Manuale utente

golmar

golmar Stadio Plus Manuale utente

CyberData

CyberData 011211 series Manuale

Vidos

Vidos duo M1021 Manuale utente

Vimar

Vimar ELVOX 7539/E Manuale utente

SSS Siedle

SSS Siedle BTSV 850-03 Manuale utente

Dahua

Dahua VTO Series Manuale utente

Elvox

Elvox 5651 Manuale utente

Videx

Videx VIDEOKIT Series Manuale utente

Rocom

Rocom Doortello Business FW T2.05W2.04 Manuale utente

Viking

Viking E-35-EWP Manuale utente

Safeguard Supply

Safeguard Supply LRA-EX1000 Manuale utente

SSS Siedle

SSS Siedle BFCV 850 Series Manuale utente

GRD

GRD MAX V2 Manuale utente

Alecto

Alecto ADI-250 Manuale utente

Aiphone

Aiphone IE-8MD Manuale utente

Perel

Perel EDB4 Manuale utente