IDEAL CONCEPT Manuale utente

CONCEPT ACRYLIC

SHOWER BATH

Installation Instructions

Please pass on to user

4994 10/17

EE74200967

4994 Concept Shower Bath:Layout 1 02/10/2017 09:53 Page 1

380

270

1695/1495

695

540

(not

including

upstand)

400

100 100

490

Plan View

Left hand bath shown

wall brackets

All dimensions shown in millimetres.

Dimensions shown may vary within permitted tolerances.

Fig. 1

CONCEPT ACRYLIC SHOWER BATH

4994 Concept Shower Bath:Layout 1 02/10/2017 09:53 Page 2

Fig. 2

CONCEPT ACRYLIC SHOWER BATH

4994 Concept Shower Bath:Layout 1 02/10/2017 09:54 Page 3

CONCEPT ACRYLIC SHOWER BATH

Fig. 3

4994 Concept Shower Bath:Layout 1 02/10/2017 09:54 Page 4

BATH CONDITION

Before commencing installation, carefully remove packaging/protective film and

check for damage. If damaged, report immediately to supplier.

The bath should be fully protected during the installation process.

INSTALLATION

1. Lay bath face down and remove legs and bags containing feet etc.

2. Locate leg adjusters, (Ref.F) on bath frame and mark positions for the fixing

screws. See Figure 1 for dimensions.

Pilot drill the holes (Ø 2mm) in the bath frame and fix leg adjusters to frame,

use screws (Ref. K).

3. Locate bath legs in leg adjusters ensuring that the orientation of the large leg is

correct and mark positions for the fixing screws on the base board. Pilot drill the

holes (Ø 2mm) in the base board, to a depth of 6mm maximum. Position legs in

leg adjusters and on base board and secure.

Use countersunk screws, (Ref. L) into the baseboard and pan head screws,

(Ref H) into the leg adjusters.

DO NOT OVER TIGHTEN.

4. Locate centre support bracket towards the centre of the baseboard, mark screw hole

positions, pilot drill holes (Ø 2mm) in base board to a depth of 6mm maximum and

secure bracket, use screws (Ref. J).

Fit the single support leg black end cap onto relevant block

(Fig. 5) using the supplied screw.

5. Fit panel clips to panel clip blocks.

The panel clips (Ref. T) must be located onto the wooden

blocks with the pan head screws supplied (Ref. W ), 29mm back

from the edge of the bath rim.

6. Fit the feet and adjust to give approximate floor to top of rim height required.

7. Turn bath over and drill for brassware if required. If the bath is to be installed

with a monoblock mixer a special hole (or holes) is required to accommodate

the mixer and will have to be cut by the installer in an appropriate position on

the rim of a no tap hole bath to suit the bathroom layout. Full details or a

template for cutting the hole (or holes) is supplied with monoblock fittings.

A template for cutting two tap holes in a no tap hole bath is supplied with

the bath.

Appropriate safety equipment/workwear should be used

The 4 black - No. 8 x 40 long countersunk crosshead self tapping screws

retaining the legs are NOT REQUIRED and should be discarded..

Fig. 4

CONCEPT ACRYLIC SHOWER BATH

4994 Concept Shower Bath:Layout 1 02/10/2017 09:54 Page 5

CONCEPT ACRYLIC SHOWER BATH

Ref. A

Ref. F

Ref. T

Ref. N

Ref. W

Ref. H

Ref. B

Ref. L

Ref. J

Ref. D

Ref. E

Ref. G

Ref. K

Ref. C

Encapsulated

baseboard

Fig. 5

4994 Concept Shower Bath:Layout 1 02/10/2017 09:54 Page 6

CONCEPT ACRYLIC SHOWER BATH

8. Fit the two wall fixing brackets to bath frame as indicated in Fig. 6 and Fig. 1.

Pilot drill holes (Ø 2mm) in frame before fixing brackets.

9. Fit brassware.

10. Place bath into installation position and level bath, ensuring that the bath height is

correct, (510mm to trimmed edge for nominal height). Note: The bath can be installed

at a lower height, but this will reduce the space available for the waste to be fitted.

Also, the panel(s) will need to be reduced in height by cutting a strip from the bottom

edge. Reducing the panel height requires great care, therefore responsibility cannot

be accepted for any errors made.

11. Fix bath to wall.

12. Fix bath to floor and ensure that all nuts are tight. Trail fit the panel(s) to verify height

is correct. Note: Untrimmed panel fitment requires the height of 540mm (510mm to

trimmed edge of bath). Remember to allow for floor coverings.

Re-adjust if necessary.

Fit the single support leg to the black cap previously fastened. Ensure that the leg is

adjusted correctly to support the rim, but not forcing the rim upwards.

13. Connect services and check for leaks.

14. Tile down to the height of the bath rim leaving a 3-4mm gap for waterproof sealant,

see Fig. 6. An extruded sealing strip can be used for the bath to wall joint as an

alternative to waterproof sealant. Protect bath during tiling.

Fig. 6

4994 Concept Shower Bath:Layout 1 02/10/2017 09:54 Page 7

Fixing the bath panel

15. Pre fit front panel ensuring that the ends of the panel are vertical. Mark a line along the

front of the panel on the floor. Remove panel and fix the plastic panel clips (Ref. T)

onto the floor/wall(s) (Figure 7). The front of the block at the floor should be 3mm back

from the marked line.

Note: The front panel may touch the support leg

foot, (Ref. N), depending on its position. Remedy

this by removing a small amount of material from

the panel return.

16. Fit the end panel by using a wooden batten along

the floor for support and engaging the top of the

panel in front of the spring clips, (Ref. Y)

secured with screws (Ref. Z).

17. Fit front bath panel in position and press the

edges into the panel clips until fully engaged.

Note: Fit end panel before front panel. If the front

panel does not easily insert under the panel clips,

then release the screws by a quarter of a turn

and retry.

Note: if the front panel has had the returns trimmed

off, then the plastic panel clips will not grip the

panel base. In this instance, use wooden blocks

(not supplied) to secure the panel to the floor/wall.

Screws with cover caps are supplied for this

method of fixing.

CONCEPT ACRYLIC SHOWER BATH

Fig. 7

Fig. 8

4994 Concept Shower Bath:Layout 1 02/10/2017 09:54 Page 8

CONCEPT ACRYLIC SHOWER BATH

CARE OF BATH

This bath left our works in first class condition and the following points should be

noted;

TO AVOID DISAPPOINTMENT, PLEASE REMOVE THE PROTECTIVE FILM AND

INSPECT BEFORE INSTALLATION.

Responsibility will not be accepted for the installation of faulty baths.

Care of bath - for the installer:

Keep under cover in a clean, dry, weather-proof place.

Do not drop. Protect completely during and after installation (with clean felt etc.).

When making joint to waste, overflow etc. on this product, DO NOT use linseed

oil putty or similar based sealing compounds. Ensure rubber washers supplied

with waste fittings are located correctly to give watertight seal.

Test the fittings and then do not use the bath for any other purpose.

Please leave this leaflet for the end user to read.

WARNING

1. Filling. It is advisable always to run in some cold water before turning on

the hot tap.

2. Cleaning. The bath should always be cleaned immediately after use, preferably

whilst the water is running out and the bath is still warm. The film of insoluble soap

products, body fats and grime which will otherwise harden on the side of the bath is

easily removed at this stage. In hard water districts insoluble lime salts are deposited

below the waterline and under leaking taps. If this deposit is allowed to build up, it

becomes increasingly difficult to remove and looks unsightly. Prompt cleaning is again

the answer. Hot soapy water with a cloth should be used and the bath wiped dry.

3. Cleaners of a gritty or abrasive nature should never be used. Worn washers on

dripping taps should be replaced.

4. Chemicals. Acrylic has good resistance properties to acids and alkalis but should

not be allowed to come into contact with organic solvents such as dry cleaning agents

and paint strippers.

5. Removal of scratches. In the event of slight scratches in the bath surface a mild

abrasive, similar to metal polish, can be used to polish these out.

6. Burning cigarettes should not be allowed to come into contact with the surface of

this bath or damage may ensue.

4994 Concept Shower Bath:Layout 1 02/10/2017 09:54 Page 9

CONCEPT ACRYLIC SHOWER BATH

Product Guarantee

25 YEARS

Idealform Acrylic baths

10 YEARS

Shower enclosures and bath screens

5 YEARS

Valves and kits, bath panels

taps and mixers

This covers products in domestic use by the consumer and not commercial or

business use.

All Ideal Standard products must be installed, used and cared for in line

with our fixing instructions, local water byelaws and current water regulations.

Access should always be left for installation, service and repair.

Any relating costs are the responsibility of the owner/installer.

Guaranteed parts will be replaced if found faulty.

This guarantee does not cover general wear and tear.

Applies to the UK and Republic of Ireland only.

Proof of purchase will be required for any warranty claim.

4994 Concept Shower Bath:Layout 1 02/10/2017 09:54 Page 10

Indice

Altri manuali IDEAL Vasca

IDEAL

IDEAL ACRYLIC Manuale utente

Manuali Vasca popolari di altre marche

Agua

Agua BARTOLI-66 Manuale utente

PAA

PAA PRELUDE Manuale utente

BETTE

BETTE SILHOUETTE Manuale utente

Kohler

Kohler K-820-GC Guida rapida

American Standard

American Standard Whirlpool/Bathing Pool 2748.XXXW Manuale utente

Oliveri

Oliveri Naples Manuale utente

Lyons

Lyons Elite ETLxx663219 Series Manuale utente

Woodbridge

Woodbridge BJ500 Istruzioni per il montaggio

Whirlpool

Whirlpool Ariel ARL-702 Manuale utente

TEIKO

TEIKO EXCELLENT DUO Manuale utente

American Standard

American Standard Colony 5-1/2' x 32" Manuale utente

American Standard

American Standard 3052OD.X0X Guida rapida

Kohler

Kohler K-1111-H2 Guida rapida

agape

agape MARSIGLIA AVAS1075 Manuale utente

Kohler

Kohler K-1151 Istruzioni per il montaggio

Kohler

Kohler K-1158 Guida rapida

Kohler

Kohler K-1244 Istruzioni per il montaggio

Kallista

Kallista P50045-G5 Istruzioni per il montaggio