iDRY Standard Manuale utente
Introduction 4.........................................................
Safety 5....................................................................
Specifications 5.......................................................
Technical Drawings 6.............................................
iDry Standard 6.......................................................................
iDry PLUS 7..............................................................................
Installation & Startup: 8.........................................
Placement 8..............................................................................
Track & Trolley Installation 9.................................................
Power 12...................................................................................
Plumbing 13..............................................................................
Loading 14................................................................................
Closing Door 16........................................................................
Powering Up 17........................................................................
Kiln Monitoring 19.................................................
Daily Monitoring 19.................................................................
Unloading Kiln 19...................................................
Opening Door 19..................................................................................................................
Checking Oven Weighted Samples 19.................................................................................
CORRECT USE 20..................................................
Lumber preparation 20.......................................................................................................
Baffling 20...........................................................................................................................
Proper Stacking 20..............................................................................................................
Reducing Degrade 20..........................................................................................................
Winter vs Summer 20..........................................................................................................
Initial Moisture Content 21.................................................................................................
iDRY User Manual
© 2020 iDRY, LLC
2
Mixing Species 21................................................................................................................
Mixing Thickness 21............................................................................................................
Frozen Lumber 21................................................................................................................
Drying Interruptions 21.......................................................................................................
MAINTENANCE & BASIC PROCEDURES 22......
Door Seal 22.............................................................................
Handwheels 23........................................................................
Chamber Interior 23................................................................
Drain 23...................................................................................
Vacuum Pump 26.....................................................................
HMI 27......................................................................................
More Information 30...............................................................
Troubleshooting 31.................................................
Troubleshooting and Alarms 31..........................................................................................
Warning labels 34...................................................
Terms and Conditions 35.......................................
iDRY User Manual
© 2020 iDRY, LLC
3
Introduction
Congratulations on your purchase of an IDRY Systems iDRY lumber dryer. This equipment
is a product of IDRY, LLC’s quality engineering and manufacturing. With a high quality
rugged stainless steel pressure vessel and state of the art electronics this iDRY dryer will,
with proper maintenance provide long term satisfactory service. To obtain the best use of
your iDRY dryer, please read this manual carefully. It will help you become familiar with the
operation of the equipment and contains helpful information regarding installation,
operation, maintenance and troubleshooting.
We hope you find this manual to be helpful in producing the high quality lumber your
customers demand.
iDRY User Manual
© 2020 iDRY, LLC
4
Safety
This equipment should be operated by trained personnel and maintained by certified
professionals. The equipment is intended for non-treated lumber only and should not be
used for any other purpose. Any modifications of the equipment or use of unauthorized parts
is forbidden unless approved by the original manufacturer. Any electrical or plumbing work
performed on this installation should be performed by certified professionals working to
local codes.
Safety warnings are noted in each section; example below:
Specifications
The following machine specifications are for iDRY Standard and iDRY Plus Lumber Dryers:
WARNING: THE VOLTAGES INSIDE THE CONTROL BOX ARE HIGH ENOUGH TO
CAUSE DEATH IF YOU COME IN CONTACT WITH THEM.
Main Power
208-240 VAC 1 Phase, 60 Amps!
Water Supply
Soft & Clean Water @ 70 Deg F / 21 C or less with avg flow of 0.75
Gallons per Minute / 2.8 Liters per minute, MIN 50 PSI
Drains
Air Gap (included) required - 2inch / 51mm PVC Connection!
Installation Environment
Above freezing dry space. For best operating performance ambient
temperature should be kept above 60 F / 15.5 C
Remote Connection
Ethernet Cable 200 Feet / 60 Meters max!
Lumber
3/4inch / 1.9cm or greater stickers recommended!
Lumber Load Capacity
STANDARD: 13ft Long x 48in Wide x 55in Tall / 3.96M Long x 1.2M Wide
x 1.4M Tall!
PLUS: 17ft Long x 60in Wide x 65in Tall / 5.18M Long x 1.5M Wide x
1.65M Tall
Drying Time
Approximately 1 week per 1 inch (2.54cm) of thickness (Maple)
iDRY User Manual
© 2020 iDRY, LLC
5
Technical Drawings
iDry Standard
iDRY User Manual
© 2020 iDRY, LLC
6
446.83
55.75
150.00
48.98 52.00 51.02
80.27
3.50
63.50 26.16
WOOD PILE
SHIM FEET SO WATER ON FLOOR
FLOWS TO BACK DRAIN ON
CONTROL PANEL END
ADJUST LEVELING FEET ON TRACK
FOR SMOOTH TROLLEY ROLLING
SIDE VIEW
OPTIONAL BRIDGE
150.00
48.00
230.02
68.62
RECOMMENDED PLYWOOD TOP
TOP VIEW
21.40
41.25 94.28 41.25
3.94
15.00
229.02
9.09
41.89
9.39
3.94
27.00
KILN CHAMBER FEET
INTERNAL TROLLEY
HAND WHEEL
BOTTOM VIEW
208-230v
1PH
60A
POWER
VENT
DRAIN CONNECTION
AIR GAP CONNECTION
0.75GPM
WATER CONNECTION
TOUCH SCREEN
REMOVABLE VENT PANELS
END VIEW
F
8
E
D
C
B
A
G
H
J
K
L
M
7
6
5
4
3
2
1
9
10
11
12
13
14
15
16
9
1
2
3
4
5
6
7
8
10
11
12
K
G
A
B
C
D
E
F
H
J
SEE NOTES SEE NOTES
DWG BY:
0.1
MATERIAL:
INTERPRET GEOMETRIC
TOLERANCES PER ANSI Y14.5-2009
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
PART NUMBER:
MOD BY:
DESCRIPTION:
CHK BY:
A1
SIZE:
SCALE:
SHT
20
OF
23
REV
1:50
iDRY Drying Systems
20
JAP
C
BA
FINISH:
MASS:
UNLESS OTHERWISE SPECIFIED
ALL UNTOLERANCED
DIMENSIONS ARE BASIC:
INSTALLATION
APR BY:
Green Mountain Mechanical Design, Inc
29 PITMAN RD BARRE, VT 05641
©2018 All Rights Reserved
CONFIDENTIAL
13
14
15
16
L
M
LAST SAVED
Monday, February 11, 2019 3:24:54 PM
iDry PLUS
iDRY User Manual
© 2020 iDRY, LLC
7
45 52 52 51
3.00
41 39.25 25 41 121 41 41
96.27
554.96
SIDE VIEW
OPTIONAL BRIDGE
ADJUST LEVELING FEET
ON TRACK FOR SMOOTH
OPERATION
252.00
82
264
9
4 58
9
4
41 37 121 41 22
BOTTOM VIEW
CHAMBER FEET
HANDWHEEL
INTERNAL TROLLEY
60.00
200.00
94.43
TOP VIEW
RECOMMENDED PLYWOOD TOP
REMOVABLE
VENTED PANELS
0.75GPM
WATER CONNECTION
208-230V
1PH
60A POWER
TOUCHSCREEN
LIFT POINTS
WATER DRAINS
END VIEW
SHIM FEET SO WATER ON FLOOR
FLOWS TO BACK DRAIN ON
CONTROL PANEL END
FOR OPTIMAL PERFORMANCE INSTALL
IN ABIENT TEMPERATURES ABOVE 60F
F
8
E
D
C
B
A
G
H
J
K
L
M
7
6
5
4
3
2
1
9
10
11
12
13
14
15
16
9
1
2
3
4
5
6
7
8
10
11
12
K
G
A
B
C
D
E
F
H
J
SEE NOTES SEE NOTES
DWG BY:
0.1
MATERIAL:
INTERPRET GEOMETRIC
TOLERANCES PER ANSI Y14.5-2009
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
PART NUMBER:
MOD BY:
DESCRIPTION:
CHK BY:
A1
SIZE:
SCALE:
SHT
21
OF
23
REV
1:50
iDRY Drying Systems
1
JAP
C
BA
FINISH:
MASS:
UNLESS OTHERWISE SPECIFIED
ALL UNTOLERANCED
DIMENSIONS ARE BASIC:
INSTALLATION
APR BY:
Green Mountain Mechanical Design, Inc
29 PITMAN RD BARRE, VT 05641
©2018 All Rights Reserved
CONFIDENTIAL
13
14
15
16
L
M
LAST SAVED
Wednesday, April 17, 2019 4:45:27 PM
Installation & Startup:
Complete the following prior to iDRY Systems assisted startup procedure:
*You can also find tutorial videos here: www.youtube.com/watch?v=Mg9MixxbL-M
Placement
1
Locate Kiln Chamber in Dry, Climate controlled space at recommended temperature of 70 DegF!
/ 21.1 C
2
Loosen Handwheels just enough to rotate them out of the way (if you continue to loosen the
threads the hand wheels will come off.
3
Shim chamber to ensure water flows to drain (chamber is pre-shimmed 1/2inch / 1.27cm)
4
Remove the ratchet Straps, then remove Track, Trolley and Bridge sections from chamber. Set
aside the cardboard box.
iDRY User Manual
© 2020 iDRY, LLC
8
Track & Trolley Installation
4
The two pieces on top are called the track bridge extensions.
5
Match up the track bridges to the chamber and the track frame using the two alignment tabs.
6
Adjust the track feet so that both the track and bridge are level leading up to the kiln chamber.
*You will need either an adjustable wrench or an 1-1/8inch / 29mm wrench. All feet should be
on the ground *The track can be used with, or without the track bridge extensions.
iDRY User Manual
© 2020 iDRY, LLC
9
7
Using a string or straight edge, aligned the track angle peak from the chamber to the opposite
far end of the track. It is imperative that the tracks on the track frame and extensions are in
alignment with the track in the chamber. Failure to do so will result in the trolley coming offthe
tracks.
iDRY User Manual
© 2020 iDRY, LLC
10
Questo manuale è adatto per i seguenti modelli
1
Indice
