IDTECK PROX10 Manuale utente

User Manual

PROX10/10H

Proximity Reader

User Manual

Table of Contents

1. SAFETY INFORMATION ...................................................................... 3

2. PRODUCT INTRODUCTION .................................................................. 5

3. IDENTIFYING SUPPLIED PARTS ............................................................ 5

4. PRODUCT SPECIFICATION .................................................................. 6

5. PRODUCT INSTALLATION ................................................................... 7

6. WIRE COLOR TABLE ......................................................................... 8

7. WIRING DIAGRAM ............................................................................ 8

8. OPERATIONS .................................................................................. 9

9. FCC REGISTRATION INFORMATION ..................................................... 10

10. PRODUCT MANUAL DOWNLOAD INFORMATION .................................... 11

User Manual

1. SAFETY INFORMATION

This caution is for safety and preventing damage of property

Please read these instructions and follow them.

1) Acquaint yourself with all instructions thoroughly.

2) Heed all warnings and follow the instruction on the product.

Keep the instruction in a conspicuous place so administrator can see it always.

Power

supply

and

installation

 Power Supply must be DC 12V.

- Higher voltage might cause electric shock,

fire and damage on the product.

 Do not install the unit in humid, dusty, or sooty locations.

- Doing so may cause fire or electric shock. .

 Do not install the unit where motor runs always.

- Doing so may cause malfunction of the unit.

 Keep out of direct sunlight and heat radiation sources.

- It may cause fire.

 If this product fails to operate normally, contact the engineer.

Never disassemble or modify this product in any way.

- Doing so may cause electric shock and fire.

 Remove the power plug from the outlet when dealing with the unit.

Do not touch the unit with the device like driver in hand.

- Doing so may cause fire and damage on the device.

User Manual

When malfunction is caused by improper handling,

service center can charge cost

Operation

and

maintenance

 When cleaning, do not spray water directly onto parts of the

product nor benzene, thinner.

- Doing so may cause fire or electric shock or damage

on the unit.

 Do not randomly change the wiring installed by engineer

or expert.

- Doing so may cause fire or malfunction or damage of the unit.

 Do not let the unit be touched by person expect administrator

for unusual purpose of using.

- Doing so may cause malfunction

Etc.

 Never disassemble or modify this product in any way.

- Contact the nearest service center when repair is needed.

- This may cause electric shock or fire.

 Keep the product out of spray or combustible substances.

- Doing so may cause explosion or fire

Damage

requiring

repair

 Contact service center in following circumstances.

- When liquid has been spilled or objects have fallen

into the apparatus.

- When the apparatus has been exposed to rain or moisture.

- When the apparatus does not operate normally.

- When there has been apparent change in operating

of the apparatus.

- When the apparatus has been dropped or the external case

has been damaged.

User Manual

2. PRODUCT INTRODUCTION

PROX10 / PROX10H have sophisticated design as well as maximum recognition

distance of 4 inch. This proximity reader can be easily attached to a metal or

doorframe or the wall. Featured by the epoxy adhesion, PROX10 /PROX10H

have high level of weather-proofing in any challenging weather conditions.

This model contains red and blue inside and Piezo buzzer guarantees accurate

and reliable system operation.

3. IDENTIFYING SUPPLIED PARTS

Please unpack and check the contents of the box.

Reader Module Bezel Quick Installation Guide

(1 ea) (1 ea) (1 copy)

User Manual

4. PRODUCT SPECIFICATION

Recognition distance /time 4"(10cm) / 30ms

Power/Current DC 12V, Max. 150mA

Output 26 bit Wiegand, 34bit Wiegand, RS232C

External buzzer control input Low Active, DC 0 ~ 12V, Max. 50 mA

External LED control input Low Active Low Active, DC 0 ~ 12V, Max. 50 mA

LED/buzzer 2 Color LED(Red/Blue) / Piezo Buzzer

Color Dark Pearl Gray

Operating temperature/humidity

14℉ ~ 140℉(-10℃ ~ +60℃),

10~90%(Humidity)

Size(WxHxD)

1.92" x 4.33" x 0.85"(49x110x21.5mm)

PROX10 and PROX10H are the same size.

Weight 0.26lb(120g)

User Manual

5. PRODUCT INSTALLATION

5-1. Inserting into doorframe / Attaching to wall

The distance between two 6-32/M3 holes which are located vertically is

3.3"(8.38cm). One 1/2" hole between them is for cable from the reader and has

1.7"(4.31cm) of distance from upper hole. (If it has been attached already, you

can skip this part)

5-2. Insert the reader cable to the hole in the middle and fix reader module

with two 6-32/M3 screws.

5-3. put the reader module in Bezel and push it until it clicked shut.

User Manual

6. WIRE COLOR TABLE

7. WIRING DIAGRAM

Signal COLOR

Main Power (+12V) Red

Power Ground (GND) Black

Wiegand Data 0 Out Green

Wiegand Data 1 Out White

Buzzer Control In Blue

LED Control In Yellow

RS232C (TX) Brown

* Please cut out tail connector before installation.

User Manual

8. OPERATIONS

8-1. When power is applied to the reader, buzzer that indicates initialization is

generated. And the Blue LED is lit once the initialization is completed. And the

reader becomes standby mode.

8-2. Put the card near the reader until LED light changes from blue to red and

buzzer is generated. Reader sends the data to controller and becomes standby

mode for following card reading.

8-3. LED Control

Color of LED can be changed by connecting LED control input(Yellow wire) to

GND. It becomes standby mode with red LED is on. If card is scanned, LED

light changes from red to blue. And then it comes back to red for following

card reading.

8-4. Buzzer control;

Normally reader makes buzzer sound only once when card is scanned. Both

authorized case and unauthorized case make buzzer sound once. However

buzzer sound can be multiple if buzzer control input (blue wire) is connected

to GND. It’s applied to unauthorized case only. When buzzer control wire is

connected to GND, it keeps making buzzer sound.

User Manual

9. FCC REGISTRATION INFORMATION

FCC REQUIREMENTS PART 15

Caution: Any changes or modifications in construction of this device which are not expressly

approved by the responsible for compliance could void the user's authority to operate the

equipment.

NOTE: This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions;

1. This device may not cause harmful interface, and

2. This device must accept any interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the limits for a Class B Digital Device,

pursuant to Part 15 of the FCC Rules. These limits are designed to this equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the radio or television off and on, the user is encouraged to try to

correct interference by one or more of the following measures.

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on another circuit.

4. Consult the dealer or an experienced radio/TV technician for help.

Altri manuali per PROX10

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali IDTECK Lettore di schede

IDTECK

IDTECK LX006 Manuale utente

IDTECK

IDTECK NEO RF245 Manuale utente

IDTECK

IDTECK SR10S Manuale utente

IDTECK

IDTECK SRK101 Manuale utente

IDTECK

IDTECK Star RFK101 Manuale utente

IDTECK

IDTECK STAR RF70 Manuale utente

IDTECK

IDTECK FGR006 Manuale utente

IDTECK

IDTECK Star RFK101 Manuale utente

IDTECK

IDTECK PROX10 Manuale utente

IDTECK

IDTECK RF900I-8 Manuale utente

IDTECK

IDTECK NEO RF245 Manuale utente

IDTECK

IDTECK ipass IP10 Manuale utente

IDTECK

IDTECK SR30 Manuale utente

IDTECK

IDTECK Star RF30 Manuale utente

IDTECK

IDTECK Star SR10 Manuale utente

IDTECK

IDTECK SR30 Manuale utente

IDTECK

IDTECK SR10RW Manuale utente

IDTECK

IDTECK Star RFK101 Manuale utente

IDTECK

IDTECK Star RFK505 Manuale utente

IDTECK

IDTECK Star RFK505 Manuale utente

IDTECK

IDTECK Star SR10 Manuale utente

IDTECK

IDTECK Star RF TINY Manuale utente

IDTECK

IDTECK Star FINGER006 Manuale utente

IDTECK

IDTECK Star SR10 Manuale utente

Manuali Lettore di schede popolari di altre marche

Lindy

Lindy 43185 Manuale utente

Lindy

Lindy 43185 Manuale utente

ViziT

ViziT RD-4F Manuale utente

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Manuale utente

AVID ID

AVID ID AVID1043 Manuale utente

Conrad

Conrad PCMCIA Manuale utente

Rosslare

Rosslare DR-6255 Manuale utente

Lindy

Lindy 51541 Manuale utente

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Manuale utente

Johnson Controls

Johnson Controls Kantech tyco ioSmart Manuale utente

ACS

ACS ACR122L Manuale utente

Secukey

Secukey S2-MF Manuale utente

Elecom

Elecom MR-SMC07 series Manuale utente

Alien

Alien ALR-9800 Manuale utente

ACS

ACS ACR310 Manuale utente

Datamars

Datamars R-IN1300 MID Manuale utente

Alarm Lock

Alarm Lock AL-PRE2 Manuale utente

xpr

xpr B100PROX-AH Guida utente