IDTECK Star 505R Manuale utente
Quick Install Guide
1
1. Check Environment
1.1 Check the power source
Before wiring, please check the voltage/current (DC12V/ 350mA) that will be input to the 505R.
1.2 Connection Diagram
Quick Install Guide
2
2. Setup Hardware
2.1 Backup Battery setup and Hardware Initialization
2.1.1 Set up the switch located in the upper-left on the back of the device from ‘OFF’ to ‘ON’ as the picture below.
2.1.2 Connect those Pink and Cyan wires with the Black wire and then turn the power on.
2.1.3 The message “Initialize OK?” will be shown on the LCD.
2.1.4 If “1” on the keypad is selected, the message “Initialize END Turn OFF Power..” will be shown on the LCD.
Turn the power off.
2.1.5 Disconnect those 3 wires (Black, Pink and Cyan).
3. Setup Controller parameter
Start Display
STAR 505R [F1]
01/01 00:00:15
READER1 MODE
RF ONLY
Enter the Master No. + <ENT>
(Default value : 00000000 + <ENT>)
Key ‘4’ or ‘6’: Left/Right
Key ‘2’ or ‘8’: Up/Down
ENT: Change or Enter
ESC: Cancel
☞In the case of SR505, press <0> key (Default setting “0000000000”+ENT)
10 times to enter the SETUP MENU.
Initialize OK?
0: NO 1: Yes
Initialize END
Turn OFF Power…
Enter “1” Key
Enter into setup mode
Quick Install Guide
3
3.1 Mode Setting (F1 Menu)
3.2 Date/Time setting (Select “TIME SETTING” Menu by the Key ‘4’ or ‘6’)
3.3 COMM Address Setting (Select “COMM ADRESS” Menu by the Key ‘4’ or ‘6’)
3.4 Card Registration (Enter F3)
Display for Mode Selection
RF-Only mode: In/Out by the Card
RF + P/W mode: In/Out by the Card + Password
PIN-Onl
y
mode: PIN
(
4 ~ 6 di
g
its
)
–
This
function is not a
pp
licable for SR505.
Press "ENT" and enter the address number (00~ 31) for communication address.
COMM ADDRESS
00
<ENT>
COMM ADDRESS
00
Display for COMM Address setting
ID REGISTRATION
Scanning…
Display for ID Registration
ID[________]
TS__ RD_
XXXXXXXX
PW____ TS__ RD_
ENT
PIN Only
RF Only
RF + P/W
ID Registered
Display for Completion
<ENT>
READER 1 MODE
-> RF ONLY
READER 1 MODE
RF ONLY
<ENT>
<ENT>
* Input the ID information
* Change the mode by the key left/right (4 or 6).
TIME SETTING
YYYYMMDDhhmmssW
200405101230302
<ENT>
Display for Date/Time setting
YYYY: Year, MM: Month, DD: Date
hh: Hour (24-hour system), mm: Minute, ss: Second
W: Sun=1, Mon=2, Tue=3, Wed=4, Thu=5, Fri=6, Sat=7
Example: 200405101230302 => 12:30:30, Monday, May 10, 2004
<ENT>
Quick Install Guide
4
3.5 Delete Card (Select “ID DELETE” Menu by the Key ‘4’ or ‘6’)
4. Normal Operation
4.1 Power ON
When the power is applied to 505R, the Red LED (LED1) is turned on.
4.2 Registered card reading
When a registered card (or PIN) is read, the Door (Relay 1) will be opened for 3 seconds (Default)
with the Green LED (LED2) light on.
4.3 Exit Button
The Exit Button or the Exit Reader should be installed inside.
When the Exit Button is pressed, the door will be opened for 3 seconds with the Green LED (LED2) light on.
4.4 Alarm (Unregistered ID /PW Error / TS Error / Door Error)
When an unregistered card is read, or any wrong password is input, or any error over the time schedule and the
door access is occurred, the access is denied and the alarm will be activated for 3 seconds (Default) with the
Yellow LED (LED 3) light on.
RF Only, RF + P/W mode: Register Card & P/W
PIN-Only mode: Register PIN (4 ~ 6 digits) – Not applicable for the SR505.
< INPUT THE ID INFORMATION >
ID: RF-Only, RF + P/W mode – Card Reading by the reader
PIN Only: Register PIN (4 ~ 6 digits) – Not applicable for the SR505.
TS: Time Schedule code (Enter the default setting value “00”)
- Enter such code for applying T/S
RD: Setup to use the reader or not (Enter the default setting value “3”)
1 – To be read only by the reader of 505R
2 – To be read only by the outer reader
3 – To be read by the both readers
Present the card for reading or enter 4~6-digit No. for deleting.
PIN only mode: 4 ~ 6-digit No. – Not applicable for the SR505.
RF-only, RF+PW mode: 8-digit (SR505: 10-digit) card No.
ENT
Display for ID Delete
ID DELETE
Enter Card No.
->__________ ENT
LED1: Power ON/OFF Status
LED2: Door Relay Status
LED3: Alarm Relay Status
1 2 3
Altri manuali per Star 505R
4
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali IDTECK Controllori di accesso IP
IDTECK
IDTECK Star 505R Manuale utente
IDTECK
IDTECK iTDC Istruzioni operative
IDTECK
IDTECK Star iCON100SR Manuale utente
IDTECK
IDTECK Star iCON100 Manuale utente
IDTECK
IDTECK GE313 Manuale utente
IDTECK
IDTECK iPass IP-RFL200 Manuale utente
IDTECK
IDTECK FINGER007 Series Manuale utente
IDTECK
IDTECK Star LX505 Manuale utente
IDTECK
IDTECK Star Finger007 Manuale utente
IDTECK
IDTECK Star LX505 Manuale utente
IDTECK
IDTECK Star 505R Manuale utente
IDTECK
IDTECK Star Finger007 Manuale utente
IDTECK
IDTECK LX007 Manuale utente
IDTECK
IDTECK ITDC ITDCSR EIO88 Manuale utente
IDTECK
IDTECK Star LX505 Manuale utente
IDTECK
IDTECK Star FINGER006 Manuale utente
IDTECK
IDTECK Star 100R Manuale utente
IDTECK
IDTECK Star iCON100 Manuale utente
IDTECK
IDTECK Star iCON100 Manuale utente
IDTECK
IDTECK Star FINGER006 Manuale utente
