Ier AUTOMATIC SYSTEM SL930 Manuale utente

The information contained in this document is the property of Automatic Systems and is confidential. The recipient is forbidd en to use it for any purpose other

than for the use of the products or the execution of the project to which they refer or to commu nicate it to third parties without the prior written consent of

Automatic Systems. Document subject to change without advance notification.

SL93x + PPV323 + TBV327-MT-EN p. 1/39

USER MANUAL

Rev 10

(Translated from French original notice)

GLASS SWING GATE

SL930 –SL931 –SL932

PPV323

GLASS

LOW-HEIGHT

TURNSTILE

TBV327

The information contained in this document is the property of Automatic Systems and is confidential. The recipient is forbidd en to use it for any purpose other

than for the use of the products or the execution of the project to which they refer or to commu nicate it to third parties without the prior written consent of

Automatic Systems. Document subject to change without advance notification.

SL93x + PPV323 + TBV327-MT-EN p. 2/39

Document changes

Rev.

Date

Written

Checked

Subject

2006-12-12

MFy

RWK + JB

Initial version

2007-04-23

Mfy

- Page 15 (locking): “locked under voltage”.

- Parameter 60°, 90°, rotating): add range and

default value.

- Input 2: “Pitch of encoder 80”.

- Page 25 (point 3): “remove the screws(31)”.

- Page 5 (1st point): “Folded and soldered

stainless steel plate housing”.

2007-06-25

Mfy

- Pages 11, 13, 15, 19: replace the terms “suction

device”and “suction mechanism”by “hold

magnet”.

- Pages 15 & 34: translate electric diagrams in

English.

2010-06-11

Mfy

RWK+HB+DL

- Complete revision for adaptation to the

modification realized on the equipment.

2010-07-01

Mfy

- Tec. Spec: replace flow by opening time of the

obstacles.

- Non-return lock option for TBV only.

2010-07-02

Mfy

- Installation: Last points of the Fixing procedure

transferred to Electrical connections and

Commissioning chapters.

- Preventive maintenance: check power leakage

and evacuation.

2011-01-17

Mfy

- SL932 added in:

·Title p1,

·Table ch.2.1,

·Installation plan ch.3.2,

·Spare parts ch.5.4,

·EC certificate ch.7.

2012-01-09

Mfy

- Ch. 2.1: MCBF, IP, CE, DAS added.

2012-10-03

Mfy

- Parts related to PPV322 & TBV326 removed

from spare parts.

2013-04-03

Mfy

YC + RWK

- Spare parts: conical coupling + references to

illustrations added.

- Ch. 5.10. adapted to software version v5.36.

- Ch.5.11. added (Maintenance Interface).

- Electrical diagrams adapted to CPU v16 +

Power board v10.

2013-08-28

SLu

- Ch. 5.4. : update spare parts table.

The information contained in this document is the property of Automatic Systems and is confidential. The recipient is forbidd en to use it for any purpose other

than for the use of the products or the execution of the project to which they refer or to commu nicate it to third parties without the prior written consent of

Automatic Systems. Document subject to change without advance notification.

SL93x + PPV323 + TBV327-MT-EN p. 3/39

Table of Contents

1. SAFETY INSTRUCTIONS 4

2. DESCRIPTION 5

2.1. Technical Specifications 5

2.2. Location of the components 6

3. INSTALLATION 7

3.1. Storage 7

3.2. Installation plans 8

3.3. Fixing the equipment to the floor 11

3.4. Electrical connections 12

3.5. Commissioning 13

4. PRINCIPLE OF OPERATION 14

4.1. Locking 15

4.2. Position encoder 16

4.3. Safety 16

5. MAINTENANCE 17

5.1. Removing the housing 17

5.2. Turning the equipment ON/OFF 18

5.3. Preventive maintenance 18

5.4. Spare parts 19

5.5. Adjusting the locking sensor 20

5.6. Adjusting the obstacle closed point 21

5.7. Setting the movement limit stops (5, p6) 21

5.8. Fitting and adjusting the locking mechanism 22

5.9. Replacing an obstacle 25

5.10. Control unit menu (program v5.36) 26

5.11. Maintenance interface 29

5.11.1. Network communication settings 29

5.11.2. Login 29

5.11.3. Status 30

5.11.4. Identification 30

5.11.5. Commands 30

5.11.6. Network 31

5.11.7. Menu Configuration 31

5.12. Trouble shooting 32

5.13. Disposal / Destruction 33

6. ELECTRICAL DIAGRAMS 34

7. DECLARATION OF CONFORMITY 38

The information contained in this document is the property of Automatic Systems and is confidential. The recipient is forbidd en to use it for any purpose other

than for the use of the products or the execution of the project to which they refer or to commu nicate it to third parties without the prior written consent of

Automatic Systems. Document subject to change without advance notification.

SL93x + PPV323 + TBV327-MT-EN p. 4/39

1. SAFETY INSTRUCTIONS

The SL93x, PPV323 and TBV327 gates and turnstiles are intended for the access control of users

and cannot be otherwise used without risk for the user or for the integrity of the equipment.

They are intended for light traffic applications (cf. technical specifications, ch.2.1. )

It is mandatory to let the equipment complete its opening and closing cycles automatically (without

pushing the obstacle) to avoid untimely out of order.

All operations on the equipment must be carried out by qualified personnel. Any unauthorized

operation, or operation carried out by a technician not qualified on this product, voids the

manufacturer’s guarantee automatically.

Access to the mechanism must be limited to personnel aware of the electrical and mechanical risks

that are incurred by negligent action.

If possible, disconnect the electrical supply before opening the enclosure.

Otherwise, turn the power off by means of the circuit breaker located on the power board (ch.5.2. ).

WARNING: In both cases, wait 5 minutes before working inside the equipment (capacitors

discharge)!

Any internal element likely to be put under voltage or to move must be handled with caution.

The equipment is configured in a minimal risk mode for its users. Any changes to the parameters

must be carried out with full knowledge of the facts by qualified personnel and are not the

responsibility of Automatic Systems.

The information contained in this document is the property of Automatic Systems and is confidential. The recipient is forbidd en to use it for any purpose other

than for the use of the products or the execution of the project to which they refer or to commu nicate it to third parties without the prior written consent of

Automatic Systems. Document subject to change without advance notification.

SL93x + PPV323 + TBV327-MT-EN p. 5/39

2. DESCRIPTION

2.1. Technical Specifications

AISI 304 stainless steel sheet housing.

Internal frame protected with epoxy coating.

Passage obstacle in clear toughened glass, thickness: 10 mm.

Electrical supply: single phase, 230 VAC, 50 Hz (not to be connected to a floating network or to high-impedance

earthed industrial distribution network).

Consumption: 0.12 A in closed and locked position,

0.50 A when turning,

0.90 A while locking.

Automatic obstacle unlocking on power failure.

Variable speed controller ensures smooth obstacle movements.

Obstacle position determined by encoder.

Operating temperature: -20(*) to +60°C (*Thanks to the heat generated by the powered internal

equipment).

RH < 95%, without condensation.

Minimum opening time of the obstacle (adjustable): 2.5 seconds.

Net weight (kg):

MCBF (Mean Cycles Between Failures), when respecting recommended maintenance: 1,000,000

cycles

IP 51

EC compliant.

DAS Certified (Powered Security Device) in accordance with Fire Safety NF S 61-937 standard

Gates and turnstiles control pedestrian access in both directions.

By definition, Direction A is the direction in which the controls are located on the right of the user (=>

obstacle opening in the clockwise direction).

PPV323

SL930

1 m

SL930

1.2 m

SL931

1.4 m

SL931

1.7 m

SL931

1.9 m

SL932

0.9m

TBV327

Column

Panels

3 x 8.4

Total

106

113

117

102

Direction A = clockwise

The information contained in this document is the property of Automatic Systems and is confidential. The recipient is forbidd en to use it for any purpose other

than for the use of the products or the execution of the project to which they refer or to commu nicate it to third parties without the prior written consent of

Automatic Systems. Document subject to change without advance notification.

SL93x + PPV323 + TBV327-MT-EN p. 6/39

2.2. Location of the components

1. Mounting base (attached to the floor)

2. Main chassis (= equipment without obstacle)

3. Obstacle (= glass panel)

4. Conical coupling of the rotor to the motor

5. Movement limit stop (not on TBV)

6. Variable speed controller

7. Locking system

8. Position encoder

9. Power supply board

10. Control board v16 (CPU)

(illustrated with optional IP module)

IP option

11. Regulated power supply

12. Obstacle support rotor

13. Additional support for high obstacle

(for SL931 only)

14. Motor

15. Serial plate

(rear)

The information contained in this document is the property of Automatic Systems and is confidential. The recipient is forbidd en to use it for any purpose other

than for the use of the products or the execution of the project to which they refer or to commu nicate it to third parties without the prior written consent of

Automatic Systems. Document subject to change without advance notification.

SL93x + PPV323 + TBV327-MT-EN p. 7/39

3. INSTALLATION

The installation must be carried out in accordance with the safety instructions (p 4) and the installation

plan (p3.2. ).

3.1. Storage

Before installation, avoid all shocks to the equipment and place it in its original packing in a dry place,

protected from dust, heat and bad weather.

Storage temperature limits: -30 to +80°C

The information contained in this document is the property of Automatic Systems and is confidential. The recipient is forbidd en to use it for any purpose other

than for the use of the products or the execution of the project to which they refer or to commu nicate it to third parties without the prior written consent of

Automatic Systems. Document subject to change without advance notification.

SL93x + PPV323 + TBV327-MT-EN p. 8/39

3.2. Installation plans

The information contained in this document is the property of Automatic Systems and is confidential. The recipient is forbidd en to use it for any purpose other

than for the use of the products or the execution of the project to which they refer or to commu nicate it to third parties without the prior written consent of

Automatic Systems. Document subject to change without advance notification.

SL93x + PPV323 + TBV327-MT-EN p. 9/39

The information contained in this document is the property of Automatic Systems and is confidential. The recipient is forbidd en to use it for any purpose other

than for the use of the products or the execution of the project to which they refer or to commu nicate it to third parties without the prior written consent of