Iflight Cinebee 75 HD Manuale utente

Instruction Manual

To receive product updates, special oers and more, register your product at www.iight-rc.com.

NOTICE: Consult local laws and ordinances before operating FPV (rst person view) equipment. In some areas, FPV operation may be

limited or prohibited. You are responsible for operating this product in a legal and responsible manner.

2019 iFlight Innovation Technology Co.,Ltd

Version：V1.01

All instructions, warranties and other collateral documents are subject to change at the sole discretion of IFLIGHT INNOVATION LIMITED.

For up-to-date product literature, visit www.iight-rc.com and click on the support tab for this product.

NOTICE

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure

to operate the product correctly can result in damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability.

Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This

product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this

product in any way outside of the instructions provided by IFLIGHT INNOVATION LIMITED. This manual contains instructions for

safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly,

setup or use, in order to operate correctly and avoid damage or serious injury.

Age Recommendation: Not for children under 14 years. This is not a toy. Safety Precautions and Warnings

• Always keep a safe distance in all directions around your model to avoid collisions or injury.

This model is controlled by a radio signal subject to interference from many sources outside

your control. Interference can cause momentary loss of control.

• Always operate your model in open spaces away from

full-size vehicles, trac and people.

• Always carefully follow the directions and warnings for

this and any optional support equipment (chargers, rechargeable battery packs, etc.).

• Always keep all chemicals, small parts and anything electrical out of the reach of children.

• Always avoid water exposure to all equipment not

specically designed and protected for this purpose.

Moisture causes damage to electronics.

• Never place any portion of the model in your mouth as it could cause serious injury or even death.

• Never operate your model with low transmitter batteries.

• Always keep aircraft in sight and under control.

• Always move the throttle fully down at rotor strike.

• Always use fully charged batteries.

• Always keep transmitter powered on while aircraft is powered.

• Always remove batteries before disassembly.

• Always keep moving parts clean.

• Always keep parts dry.

• Always let parts cool after use before touching.

• Always remove batteries after use.

• Never operate aircraft with damaged wiring.

• Never touch moving parts.

This product uses Betaight Third Party Software in portions of its coding. For more information on Betaight Software, please visit:

https://github.com/betaight/betaight/wiki.

THIRD PARTY SOFTWARE: This product may include code developed by one or more third parties (“Third Party Software”). Some

Third Party Software may be subject to other terms and conditions that may be available for download with the product documentation.

Notwithstanding the terms and conditions of this Agreement, the Third Party Software is licensed to you subject to the terms and

conditions of the software license agreement identied in the open source software disclosure. If the third party terms and conditions

include licenses that provide for the availability of source code (such as the GNU General Public License), the open source software

disclosure or the media on which the software may be delivered will provide instructions where a copy of such source code can be obtained.

CINEBEE 75HD BNF DRONE

- Optional Receiver

- 4 x 1103 10000Kv FPV Motors

- SucceX Micro F4 Flight Controller

- SucceX 12A 4-in-1 ESC Dshot 600

- 25/100/200mW Adjustable Video Transmitter

- Caddx turtle V2 FPV Camera

- 1.6 inch 1.5mm hub Gemfan and HQ prop

- Battery Straps

CineBee 75HD

SPECIFICATION

Weight: 68g (without battery)

Motors: 1103 10000KV 2-3S

SucceX Micro F4 y tower(w/12A 2-4S ESC+F4 FC+VTX 0-200mW)

Props: HQ prop 1.6" 4-Blades Prop（Gemfan 1.6" 3-Blades Prop）

HD DVR Camera: CADDX Turtle V2

Receiver Option: Frsky XM+ / DSMX / Futaba S-FHSS / Flysky / TBS Crossre

Frame: CineBee 75HD Frame

Battery strap ts for micro 2S-3S battery

Flight time: 3 min 30 sec with 450mAh 3S battery

BOX CONTENTS:

Parts Explosion Parts Listings

1- Propeller

2- BeeMotor 1103

3- Prop guard

4- M2 screw

5- Camera board cover

6- Carbon ber protective plate

7- M2 x25 stando

8- 3D print camera mount

9- Caddx turtle V2 FPV Camera

10- Top plate

11- Receiver

12-3D print receiver holder

13- SucceX micro ytower

14- Flywoter adapter mount

15- Bottom plate

16- Caddx turtle V2 camera record board

Installing the Propellers

1. Refer to the illustration for the proper motor rotation and propeller location.

2. The propellers have “CW” or “CCW” marked on one blade to show proper location

and rotation. Match the propeller location to the illustration.

3. To take o the propeller, hold the motor bell and twist the prop back and forth...

*Grasp bell before removing props to avoid damage in case you want to change

the default propeller installing

Transmitter and Receiver Binding

CAUTION: Always disconnect the Li-Po battery from the quadcopter when not

ying to avoid over-discharging the battery. Batteries discharged to a voltage

lower than the lowest approved voltage may become damaged, resulting in loss of

performance and potential re when batteries are charged.

To bind or re-bind your quadcopter to your chosen transmitter, follow the directions below.

General Binding Procedure

1. Select the correct model in your transmitter.

2. Power on your transmitter.

3. Lower the throttle fully.

4. Power the quadcopter on while pressing the bind button on the TPU 3D print

mount, as shown in the picture.

5. Follow the procedures of your specic transmitter to enter Bind Mode.

6. The receiver LED glows solid orange indicating binding was successful.

If you encounter problems, obey binding instructions and refer to the

troubleshooting guide for other instructions.

Failsafe

The included receiver does not have failsafe capabilities. Failsafe is detected at the ight controller. In the event of a loss of signal to the

receiver the ight controller will cut power to the motors to prevent a y-away situation.

How to Binding your Taranis

The following steps are the actual binding procedures for the OpenTX Taranis series of radios:

1.Power o your quadcopter (RX) and power on your Taranis.

2.Press the Menu button on the Taranis to activate the Model Selection page.

3.Select an un-used model and press Page.

4.Optionally select and enter a name for your new quadcopter.

5.Using the +/- buttons, scroll to the bottom of the menu to Internal RF | Mode.

Select D16 for all miniquad receivers (which includes X4R-SB, XSR, XM+).

6.Scroll down to [Bind] using the – button. Press the ENT button on your TX to enable binding mode.

Your Taranis should begin making an intermittent chirping noise.

7.Find the physical push button on your RX. It is most often next to the LED that turns on when it is powered up.

On the XM+ it is very small and near the antenna. This is the Failsafe button.

8.Press and hold the Failsafe button while powering up your receiver/quadcopter.

This can take more than two hands, so you may need to have some help.

9.When the receiver powers up, you should see a solid green light and a blinking red light. This indicates success.

Any other light scheme means you likely have a problem, you should try the process again or consult the FrSky manual.

10.On the Taranis, press ENT to exit bind mode. Press EXIT several times to go back to the home page.

11.Power your receiver/quadcopter back on. Verify that it is showing a solid green light, indicating that it is successfully communicating

with the radio. If your RX supports telemetry, you should see radio signal telemetry show up on your

How to Binding your nano RX

1. Just power up the TBS CROSSFIRE transmitter

2. On the standard transmitter, enter the conguration menu by pressing and holding the joystick for

3 seconds, select “General” and “Binding” - a message “Binding” will start blinking, waiting for the receiver. On the micro transmitter,

a short press on the button will initiate binding mode.

3. Now, power up the receiver (without pressing the Bind button!), if your receiver has not been previously bound, it will automatically bind.

Otherwise, press and release the “BIND” button on the receiver to initiate binding. On the receiver is a timeout of one minute for after

power up to enter bind mode. If the status LED will start blinking slowly the receiver has switched successfully to bind mode.

4. Within a few seconds the process will nish with a “Binding complete” message on the standard transmitter, or a solid green LED on the

micro transmitter. The receiver has now stored the unique serial number of that particular CROSSFIRE transmitter. If it doesn’t bind,

please verify that your rmware is to the newest version on both the receiver and the transmitter.

CADDX Turtle V2 Cam Quick operation guide:

As a quick note, the place to type is at the bottom of the screen, not on the grey screen itself.

*Within the CLI type:

*set spektrum_sat_bind = 9 - for DSMX

*set spektrum_sat_bind = 5 - for DSM2

*Type save, your ight controller will now reboot. Once it has rebooted, remove the USB cable to power o the ight controller.

*After a second, reconnect the USB cable and your receiver should ash (indicating it is in bind mode)

*Turn on your R/C controller while holding the bind button (on the controller).

*Once the binding is complete, the LED on the receiver should stop blinking.

*Now connect back to BetaFlight and you can conrm it is bound by going to the receiver tab, and you should see the bars moving when you move your R/C

controller sticks.

*Now you need to turn o bind mode on your receiver.

*To do this go back to the CLI and type set spektrum_sat_bind = 0

*Type save to apply the settings. The board will reboot and now have completed the binding process!

1. RIGHT BUTTON: Press the RIGHT button for 3s-5s to activate video recording, in the meanwhile the light on the lower right corner will icker.

2. LEFT BUTTON: Press the LEFT button for 3s-5s to stop video recording.

3. DOWN BUTTON: Press the DOWN button for 3s-5s to switch the resolution, 720P with Blue LED on, 1080P with Red LED on, the default mode is 1080P.

4. MIDDLE BUTTON: The MIDDLE button is the menu button.

Notice: The camera need at least 8G Class 10 SD card.

Notes: If the power is cut accidentally when video recording, please power on again, then the camera will automatically restore the memory,

and the video records before power cut will be still saved in TF card.

How to Binding your Spektrum

SucceX Micro F4 OSD Setup in Betaight Congurator：

The OSD conguration in Betaight Congurator is mercifully simple. It all starts in the new “OSD” tab:

OSD Setup in the eld

To access the menu, turn on your quadcopter, don your goggles and hold the following stick combination on your radio: Throttle stick mid, Yaw stick left,

Pitch stick up, Roll stick centered. The menu should appear within 1 second.

From here, you can scroll through the menu with your pitch stick. Pressing right with the roll stick will activate the current selected option. Some options,

like the PIDs, are numbers which can be adjusted up with right roll stick and down with left roll stick.

Transmitter stick movements

Understanding the Primary Flight Controls

If you are not familiar with the controls of your quadcopter, take a few minutes to familiarize yourself with them before attempting

your rst ight.

Throttle

Rudder

Elevator

Aileron

Throttle up

Rudder left

Elevator down

Aileron left

Throttle down

Rudder right

Elevator up

Aileron right

Left Side View Left Side View

Rear View Rear View

Climb

Descend

Nose Yaws

Forward Backward

RightLeft

left left

Adjusting the FPV Camera Angle

Adjust the angle of the FPV camera by gently pushing the

lense up or down to the desired angle.

Post-Flight Inspection and Maintenance Checklist

WARNING: Remove the propellers from the motors prior to performing any troubleshooting or maintenance.

Failure to do so may cause serious injury if the motors start unexpetedly.

Cleaning Make sure the battery is not connected before cleaning. Remove dust and debris with a soft brush or a dry, lint-free cloth.

Motors

Wiring

Fasteners

Propellers

Replace the motor when the model will not y steady or veers o when doing a climb out.

Make sure the wiring does not block moving parts. Replace damaged wiring and loose connectors.

Make sure there are no loose screws, other fasteners or connectors. Do not over-tighten metal screws in plastic

parts. Tighten screws so the parts are mated together, then turn the screw only 1/8th of a turn more. Do not use

threadlock on or near plastic parts.

Make sure there is no damage to the propellers or other parts that move at high speed. Damage to these parts

includes cracks, burrs, chips or scratches. Replace damaged parts before ying.

Troubleshooting Guide

WARNING: Remove the propellers from the motors prior to performing any troubleshooting or maintenance.

Failure to do so may cause serious injury if the motors start unexpetedly.

Problem Possible Cause Solution

Diculty binding

*Bind button not pressed while powering

on the quadcopter Power o quadcopter and repeat bind process

*Bind switch or button was not held

while transmitter was powered on

*Transmitter too near aircraft during

binding process

*Quadcopter or transmitter is too close

to large metal object, wireless source

or another transmitter

Power o quadcopter and repeat bind process

Power o transmitter. Move transmitter farther from the aircraft or

shield the aircraft from transmitter using your body. Disconnect and

reconnect ight battery to quadcopter. Follow the binding instructions

Move quadcopter and transmitter to another location and attempt

binding again

Yellow screen

*Cable loose/Damaged cable Use a new cable

*On-board components fell o Contact us, we will replace a new Caddx turtle V2 for you

Jello video

Try a camera lens on it

Make sure camera mount is xed

Make sure the motor is good rotating

Make sure prop is balanced

Make sure your frame bolts are tight

*Sunlight too strong

*Camera screws loose

*Motor stucked

*Prop unbalanced

*Frame bolts loose

Quadcopter is not lift up *Wrong prop direction Change your motor direction or prop direction

CAUTION: Changes or modications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

Huizhou iFlight Innovation Technology Co.,Ltd

F3,NO.2 Huayu Road,Zhongkai Hi-tech Zone,Huizhou,Guangdong,CHINA

Tel: 86-752-3866695 Web: http://www.iight-rc.com

Product info in description depends on the actual product,specications

are subject to be changed without prior notice.

Indice

Altri manuali Iflight Drone

Iflight

Iflight DOLLA BMCC Manuale utente

Manuali Drone popolari di altre marche

Ryze

Ryze Tello Manuale utente

PowerVision

PowerVision PowerRay Manuale utente

Force1

Force1 rogue F72 Manuale utente

Zerotech

Zerotech DOBBY Manuale utente

Protocol

Protocol VIDEODRONE AP Manuale utente

dji

dji Matrice M210 Manuale utente

MAKE

MAKE Terry Kilby Manuale utente

SYMA

SYMA X440 Manuale utente

RUKO

RUKO F11 Manuale utente

SYMA

SYMA X5UW(720P) Manuale utente

Dynali

Dynali 25 H Guida

dji

dji PHANTOM 4 Manuale utente

Atlas

Atlas AtlasPRO Manuale utente

Twodots

Twodots TVVIN BOARD Manuale utente

GDU

GDU SAGA Manuale utente

Ares

Ares ETHOS QX 130 Manuale utente

Walkera

Walkera ZHUN Manuale utente

dji

dji WIND-4 Manuale utente