IGM 142-ST97 Manuale utente
Distributor:
IGM nástroje a stroje s.r.o.
Ke Kopanině 560, 252 67, Tuchoměřice
Czech Republic, EU
Phone: +420 220 950 910
E-mail: [email protected]
Website: www.igmtools.com
IGM Straightline Edgebanding and Trimming Kit for Worktable ST95A
Operationg instructions
2022-07-13
142-ST97 IGM Trimming Kit Manual EN v2.6.00 A4ob
142-ST97
www.igmtools.info
PDF ONLINE
-2-www.igmtools.com
Operating Instructions EN
Please read this manual thoroughly and follow the safety instructions in it! Technical changes and
printing errors reserved!
Dear customer,
this manual contains information and important guidelines for the assembly and proper use of the Straightline
Edgebanding and Trimming Kit.
Please read and follow the safety instructions!
Carefully read these instructions before using the machine. Operation of the machine will be simpler and
you will also lower the risk of injury while eliminating the probability of incorrect operation and possible
damage to the machine.
Because of our policy of constant improvement, the design, construction or pictures may differ slightly.
Should you discover any mistakes, please contact us at podpora@igm.cz.
1.1 Set description
1
Front fence
Guiding the work piece to
worktable at the front
2
Back fence
Guiding the work piece through the
work table
3Stable plate
Spacer for passing edge band
4Moveable frame
Leveling spacer for work piece
5Lead fence
Lead work piece to worktable
11 Straight lead fence
Fix trimmer holder on worktable.
12 Trimmer holder
Fasten trimmer
1. SPECIFICATIONS
Assemble and operation
• Worktable is compatible for straightline edge banding and trimming operation, follows (Fig1) to begin
installation.
• Make sure the roller is horizontal to the back fence and fasten by screw (Fig 2).
• Make sure the room between front and back fence can fit the tap and two fences are horizontal (Fig 3).
Adjust horizontally
between two fences
Spacer for edge band
Fasten with screw
Fig 1 FIg 2 Fig 3
4
4
2
3
11
12
5
1
-3-www.igmtools.com
Operating Instructions EN
Fig 4 Fig 5 Fig 6
Mount and operate trimmer on worktable
• Mount trimmer on the worktable, and operate with straightline trimming procedure.
• Make sure the trimmer is mounted with adjustable handle, axle.1 and cap.2 stably. Also screw the cap.2 and
cap3 tightly. (Fig 2)
• Make sure the trimmer tightened with screw.1 and trimmer holder can swag, than fasten the cap.A tightly。
• Fasten screw.2 to the side of work table tightly (Fig3).
Fig 1 Fig 2 Fig 3
• Mount and fasten the lead plate on worktable. (Fig 4)
• Adjust the appropriate length for work piece and fasten with adjustable handle. (Fig 5)
• Set the appropriate width for the work piece, and follow the direction shown on (Fig 6)
• Adjust the bearing with router bit lean against work piece. Fasten the adjustable handle and check the trimmer
holder which can swag up and down. After the correction, place movable plate on work table, adjust the
appropriate width and follow the instruction as shown on (Fig6)
Fig4 Fig 5 Fig 6
14
13 4
4
IGM nástroje a stroje s.r.o., Ke kopanině 560,
Tuchoměřice, 252 67, Czech Republic, E.U.
+420 220 950 910,www.igmtools.com
© 2022 IGM nástroje a stroje s.r.o.
Indice
Altri manuali IGM Accessori per utensili elettrici
