iHome ID28 Guida
Questions? Visit www.ihomeaudio.com
Model iD28
App-enhanced Portable
Rechargeable System for
iPad ®, iPhone®and iPod ®
iD28IBinEnglishversion
Printcolor:Blacktextonwhitepaper
Sizeofmanual:178mmWx178mmH
July13,11
iHome + Sleep
works with
iHome + Radio
alarm clock app
internet radio app
Note: iHome+Sleep and iHome+Radio apps are not covered in detail in this booklet. To learn more about how
these apps can enhance your experience, please download the free iHome+Sleep app from the App Store and
review the Start Guide.
download QR code
reader app and scan
Table of Contents
and are registered trademarks of SRS Labs, Inc.
TruBass and WOW technologies are incorporated under license from SRS Labs, Inc.
Controls and Indicators / iD28 Display 1-2
Quick Start 3-4
Getting Started 5
Connect AC adaptor and Install Clock Backup Battery
Charging Internal Battery 6
Reset the iD28 6
Setting Up the iD28 7
Updating Firmware, Docking iPhone/iPad/iPod, Setting the Time and Calendar using IPhone/iPod Time Sync,
Setting Time and Calendar Manually
Using the Alarm 8
Setting the Alarm, Review, Arming and Disarming Alarm
Resetting the Alarm to Come on the Next Day, Sure Alarm, Snooze/Dimmer
Listening to iPhone/iPad/iPod 9
Listening to FM Radio 9-10
Setting up the Antenna, Tuning and Playing the Radio
Setting FM Radio Frequency/Range to use iD28 in Other Countries
Using the Aux Line-In Jack with other Audio Devices, Sleep Timer, Using the Remote auto/on switch 10
A Consumer Guide to Product Safety 11
Troubleshooting 12
Warranty Information 13
• Place the unit on a level surface away from sources of direct sunlight or excessive heat.
• Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective material
should be placed between it and the furniture.
• Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as Benzene,
thinner or similar materials can damage the surface of the unit.
Maintenance
FCC Information
This equipment complies with the limits for a Class B digital device as specified in Part 15 of FCC Rules. These limits
provide reasonable protection against radio and TV interference in a residential area.
However, your equipment might cause TV or radio interference even when it is operating properly. To eliminate interference
you can try one or more of the following corrective measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and the radio or TV.
• Use outlets on different electrical circuits for the equipment and the radio or TV.
• Consult your dealer or an experienced radio/television technician if the problem still exists.
Modifying or tampering with your system’s internal components can cause a malfunction and might invalidate the system’s
warranty and void your FCC authorization to operate it.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
1
Controls and Indicators
Front Panel
Top Panel
Power Button
EQ Button
Volume Up Button
Wake Up Button
Volume Down Button
Bedtime Button
Radio/Aux Button
Alarm Button
Clock Sync Button
Presets Button
Play/Pause Button
Snooze / Dimmer
Button Reverse Button Forward Button
Speaker
Speaker
Retractable Dock
2
Controls and Indicators
FM antenna/Aux line-in Jack (at Rear Panel)
Time Display
PM Indicator
Alarm Indicator Low Backup Battery Indicator
Rechargeable Battery Status Indicator
Preset / iPod / Radio / AUX / Wake-to / Sleep indicators
SRS Indicator iHome App Indicator
Display
Rear Panel
FM antenna /
Aux line-in Jack Adaptor Jack
DST Switch
Fold out stand Fold out stand
Remote auto/on switch
Reset Button
Radio stereo/mono switch
Back Up Battery
compartment
FM antenna/Aux line-in Jack
FM antenna
3
RESET
RESET
TEST
TEST
iD28 Quick Start
1:Stand 2:Power
Fold out the stand feet on the bottom of the unit, then
turn unit upright for operation.
Plug the AC adapter into the adapter jack on the rear of the
unit and the other end into a working outlet. The first time
you connect the unit you should let it charge the internal
battery completely (about 5 hours).The internal battery (and
docked iPhone/iPad/iPod) will charge.
3:iPhone/iPad/iPod
• Press on the iHome logo on front of the unit to release the
dock (press in for travel)
• Gently dock playing iPad/iPhone/iPod. The unit will turn on
and your audio will play through the unit.
• Press the or Buttons to adjust volume
• Press the EQ Button to cycle to Treble, Bass and SRS,
press or to adjust settings.
• Press the Button to turn unit off.
4:Time Sync
• Make sure unit is OFF and iPhone/iPad/iPhone
is docked
• Press and release the Clock Sync Button on
the top left of the unit. “SYNC” will flash in the
display, followed by 2 beeps indicating time
sync was successful.
• If “FAILED” appears on the display and a long
beep sounds, sync was unsuccessful. Try again
with a different iPhone/iPad/iPod, or set clock
manually (see page 7).
Press
clock sync
4
iD28 Quick Start
5:Radio
• Attach included FM antenna to FM Antenna/Aux line-in jack on back of unit
• Press and release the Radio/AUX Button as needed to select FM radio mode.
• Press and release the or Buttons to tune radio to desired station; press and hold briefly to scan to next
clear station
• See page 9 for information on setting FM presets
5
Thank you for purchasing the iD28. Designed specifically to work with your iPhone, iPad and iPod, and with iHome apps like
iHome+sleep and iHome+radio this system provides high quality audio performance that brings out the best in your music
and lets you wake and sleep to it anywhere. These instructions do not cover the use of apps. For more on using this unit with
iHome apps, please visit iHomeaudio.com/apps or look for iHome in the App Store.
Please read these instructions carefully before operating the unit and keep them for future reference.
Connect AC Adaptor
Connect the AC adaptor cable plug into the DC jack on the back of the system, then plug the AC adaptor into a working
outlet. While connected to AC power, the iD28 will charge your docked iPhone, iPad or iPod as well as the internal lithium ion
battery until fully charged.
Installing/Replacing the Clock Backup Battery
Note: The CR2032 lithium battery is included in the unit. Please pull out the battery pull tab before you use the unit.
This model is equipped with a battery backup circuit that will maintain the time and alarm time settings, as well as the radio
station preset memory settings and EQ settings in the event of a temporary power interruption. The battery backup circuit will
also operate the buzzer alarm to wake you up even if the power is out at the selected wake up time. The battery backup
circuit requires one CR2032 lithium battery, included.
When the backup battery is getting weak the Low Backup Battery Indicator will begin flashing in the display. When you see
this flashing indicator you should replace the backup battery as soon as possible. Purchase a replacement CR2032 battery,
available wherever batteries are sold, and follow steps 1 through 4 below to install the replacement battery.
To replace the backup battery:
IMPORTANT: When replacing the backup battery be sure to have the unit connected to the AC outlet to maintain all of your
settings, otherwise it will be necessary to reset the time, alarm time, radio presets, and EQ settings after the
battery is replaced.
1. Locate the battery backup holder found on the rear of the unit towards the top center.
2. Pinch the locking tab on the right of the battery holder toward the center of the battery
holder to unlock it and insert a thumbnail into the slot in and pry gently outwards to
remove the battery holder.
3. Insert a fresh CR2032 battery in the backup battery holder with the “+” side facing up, as
illustrated.
4. Replace the battery holder and confirm that the backup battery indicator is not
flashing in the display.
Note: Make sure you dispose of battery properly (see your local regulations).
WARNING: Lithium batteries can explode or cause burns if disassembled, shorted, recharged, exposed to water, fire,
or high temperatures. Do not place loose batteries in a pocket, purse, or other container containing metal
objects, mix with used or other battery types, or store with hazardous or combustible materials. Store in
cool, dry, ventilated area. Follow applicable laws and regulations for transport and disposal.
Getting Started
6
Your unit comes with an internal lithium ion battery for portable operation. As noted above, the internal battery charges when
the unit is connected to AC power. A battery status indicator is located to the right of the clock display. When the indicator
is low and flashing, you will need to connect the unit to AC power to recharge the battery. When the indicator is full and steady
(not flashing), the battery is fully charged.
End-Of-Life Battery Disposal Instructions
This device uses a Lithium-ion battery that should last the lifetime of the device. If you suspect your battery may be dead, try
charging it several times. If the battery does not recharge, please contact us for repair information. Please do NOT attempt
to change the battery yourself. If the battery has died and you do not want us to replace your battery, you should follow the
disposal instructions below.
Consult local laws and regulations for proper battery disposal in your region. If there are no local regulations concerning
battery disposal, please dispose of the device in a waste bin for electronic devices.
Caution: The Battery used in this device may present a risk of fire, explosion or chemical burn if mistreated
Battery shall not be exposed to excessive heat such as sunshine, fire, or the like. Do not use or charge the battery if it appears
to be leaking, discolored, deformed, or in any way abnormal. Do not leave your battery discharged or unused for extended
periods of time. When batteries are misused, they may explode or leak, causing burns and personal injury. If your battery
leaks, use normal precaution and discard the battery immediately.
Your iD28 was designed with a special surge protection circuit to prevent permanent damage
to the unit in the event of an unexpected power surge. If your unit appears to be ‘locked up’
and is not operating normally, and you know that the battery is properly charged, use a
straightened paper clip, toothpick, or similar object to press the RESET button, located on the
back panel next to the AC jack. This will unlock the unit and restore the original factory default
settings.
Charging the Internal Battery
Resetting the iD28
Setting Up the Unit
7
Updating your Firmware
To update the firmware on this unit to the latest version, please download the free iHome+Sleep app from the app store.
Launch the app and follow directions for updating the firmware for this unit if available.
Docking your iPhone, iPad or iPod
1. Press on the iHome badge on the front of the unit to release the retracting dock (press in again for travel).
2. Carefully place your iPhone/iPad/iPod into the dock.
Setting the Clock
Setting the Time and Calendar using iPhone/iPad/iPod Time Sync
Time sync mode allows you to sync the unit to the time and calendar from your iPhone, iPad or recent models of iPod like
iPod Touch, iPod Nano and iPod Classic (older models such as iPod Mini do not support this feature).
1. Make sure your iPhone, iPad or iPod is properly docked and the unit is OFF. Press and release the Clock Sync Button
located on the top left of the unit. “SYNC” will flash on the display, indicating sync function is in progress.
2. After sync is complete, the display will show the current time and two beeps will confirm time sync is done.
3. If time sync fails, “FAILED” appears on the display a long beep sounds and the unit exits time sync mode. Try using a
different iPhone/iPad/iPod to attempt syncing again or set time manually (see below).
NOTE:
The iPhone is constantly updated to current time via cell phone towers. The time on your iPad or iPod is only
accurate to the last time it was synced to a computer.
It’s possible to have up to 59 seconds difference between the unit and
synced iPhone/iPad/iPod.
Setting Time and Calendar Manually
1. Set the DST Switch located on the back of the unit to +1 to add one hour or to -1 to subtract an hour to account for
daylight saving time or standard time
2. Press and hold the Clock Sync Button until the hour display flashes. Press the or button to set the correct hour
(press and hold for rapid advance). Remember to set the correct AM or PM time. The PM Indicator is located to the
upper left side of the time digits; there is no AM indicator.
3. Press the Alarm Button at any time during clock setting to toggle the display between 24 hour (military) and 12 hour
(standard) display mode. The PM indicator will not appear when display is in 24 hour mode.
4. Press the Clock Sync Button. The minutes will flash. Press the or button to set the current minutes.
5. Press the Clock Sync Buttonn. The year will flash. Press the or button to set the current year.
6. Press the Clock Sync Button. The date will flash. Press the or button to select the current date (press and hold
to enter fast scroll mode).
7. Press the Clock Sync Button again (or no button press within 10 seconds) to exit the clock setting mode. 2 beeps will
confirm clock setting is complete.
Indice
Altri manuali iHome Stazione di attracco
iHome
iHome Studio Series Manuale utente
iHome
iHome iHome iPL8 Manuale utente
iHome
iHome iH7 Manuale utente
iHome
iHome iD8 Manuale utente
iHome
iHome IHOME ID85 Manuale utente
iHome
iHome iHome iP10 Manuale utente
iHome
iHome iH25 Manuale utente
iHome
iHome iH69 Manuale utente
iHome
iHome IP39 Manuale utente
iHome
iHome Studio Series Manuale utente
