Ihse K450-1S Manuale utente

Dear Customer,

congratulations to purchase the DAVX-Digital Audio Video EXtender. This product correspond to the

ultimate requisitions for quality and technics. If you still have problems with your device, please refer to

your sales office.

The DAVX-Extender allows you to remotely position your Video-, Stereo-Audio- and V24- devices up to

10km. Different devices use different cabelling (Cat5 or fiber) or support differnt features (unidirectional

or bidirectional transmission, digital or analogue Audio, ...)

Please read this manual before installing and operating the units. Please record the serial number, the

date of purchase and your sales office. The serial number is located on the backside of the units. These

data would be important, if you ever need to repair one of the parts.

DAVX-Digital Audio Video Extender

unidirectional transmission over Cat5, digital Audio, +RS232 ........................K452-1S

unidirectional transmission over Cat5, analog Audio, +RS232 .......................K452-2S

unidirectional transmission over Multimode, digital Audio, +RS232....................K450-1S

bidirectional transmission over Multimode, digital Audio, +RS232.....................K450-1D

unidirectional transmission over Multimode, analog Audio, +RS232 ...................K450-2S

bidirectional transmission over Multimode, analog Audio, +RS232 ....................K450-2D

unidirectional transmission over Singlemode, digital Audio, +RS232 ..................K451-1S

bidirectional transmission over Singlemode, digital Audio, +RS232 ...................K451-1D

unidirectional transmission over Singlemode, analog Audio, +RS232..................K451-2S

bidirectional transmission over Singlemode, analog Audio, +RS232...................K451-2D

IHSE by Scanmagnetics Oy • Helsinki • Finland

• www.scanmagnetics.com • [email protected] • Tel. +358-9-271 2200

Audio-/Video-Extender up to 10km

for FBAS- or Y/C-Video

with digital (analog) Audio- support

and serial (RS232) Interface

revision: January, 2004 DAVX - dig. A/V-Extender

You have purchased a valuable device,

which should meet best all

requirements. To do this, it is

necessary, to get an overview of

behavior of the device, its functions and

the different setup pssibilities and

options.

Please read this manual carefully.

Please record the serial number and

the date of purchase inside of this

manual. The serial number is located

on the backside of the units. These

data would be important, if you ever

need to repair one of the parts. For

competent users, we suggest, to read

et least the part ‘Quick Startup’.

If you have any question to the product,

or if you need aid at installation time,

please do not hesitate to contact your

dealer. He will like to support you.

Serial Number

date of purchase

Your dealer

revision: January, 2004 DAVX - dig. A/V-Extender

TABLE OF CONTENS

Introduction 20

Technical data 21

Compatibility 21

Features: 22

Connectors/Cables 22

Transceiver-Modules (Fiber Transmission) 24

Diagnostics 25

Getting Started 26

Firmware Upgrade 27

IR-Control 27

Usage of IR-Control 27

Serial Interface (V24/RS232) 28

analogue AUDIO-Interface 29

Order Notation 30

schedule of parts supplied 31

CE declaration of conformity 32

Disclaimer 32

Introduction

Features

This product has a number of unique features that allow transparent remote operation of your

Video-/Audio- Equipment.

•Transfer your Audio-/Video-Signal in digital Quality over Cat5 up to a distance of 100m, You

need only a single CAT 5 twisted pair cable. Please use installation cables (with solid wires) -

patch cables (with stranded wires) are not useful for bridging distances. The RS232-Interface

allows, to remotely control your devices e.g. your camera.

•Transfer your Audio-/Video-Signal in digital Quality over Multimode Fibre Cables up to a

distance of 400m, You need only a single fibre pair. The RS232-Interface allows, to remotely

control your devices e.g. your camera. The bidirectional devices allow simultaneous

transmissions in both directions.

•Transfer your Audio-/Video-Signal in digital Quality over Singlemode Fibre Cables up to a

distance of 10,000m (=10km!). Other features like Multimode

•Using an Infrared Remote Control, you can select the input video format (PAL/NTSC), the

video source (FBAS or Y/C) and adjust brightness or contrast. Prssing a single key, you can

recall the factory settings or set brightness and contrast to default values.

Mounting arrangement

revision: January, 2004 DAVX - dig. A/V-Extender

20 Introduction

PLAY

REC

OFF

FRONT LOADING

TwinSpeed 8 DayTim

Recorder

Player

Technical data

power supply

local unit : international power supply unit

90..240VAC-0,5A-47..63Hz/6VDC-2000 mA

remote unit : international power supply unit

90..240VAC-0,5A-47..63Hz/6VDC-2000 mA

Interfaces

Video (main) : Input Level 0,7Vpp, 1vpp (-3dB)

Input Impedance 75 Ohm

Input Capacity max 10pF

Output Voltage 0...1,4V

Output Current app. 17mA @ 37,5 Ohm

Video FBAS : PAL/NTSC, format independant

Video Bandwith 7MHz

Video Y/C (SVHS) : PAL/NTSC, format independant

Video Bandwith 7MHz

Audio digital over S/P-DIF up to 6MHz Sampling Rate format independant

(96kHz with 64Bit) NRZ Code

Transmission Length 0,2...10m POF Plastic Fibre (970/1000μ)

pulse width distortion +/- 20ns

optical power -21dB ... -15dB

Wavelength 660nm

Audio analog : bidirectional near CD Quality, 38,4kHz, 16Bit

serial (RS232) : fully transparent with Handshake up to 19200 Baud

Interconnect Cable (not in schedule of parts)

Cat5/5e/6/7 : 100m (Installation cable 4x2xAWG24 or AWG23)

Cat5/5e/6/7 60m (Patchcable 4x2xAWG26)

62,5μ/50 μ Multimode : 200m (@62,5μ) / 400m (@ 50μ)

9μ Singlemode : 10km

Dimensions

Weight : app. : 3,0 kg (Kit, 0,5kg per unit)

Length/Width/Height : maximal: 170 x133x44mm

Temperature : Operation app. 10°C ... 45°C

Compatibility

To operate in various environments and with hardware from many manufacturers, this product

has a number of specific features, and has been tested with a wide variety of hardware.

However, it is impossible to guarantee correct operation with every Video-/Audio-Device currently

on the market.

IHSE by Scanmagnetics Oy • Helsinki • Finland

• www.scanmagnetics.com • [email protected] • Tel. +358-9-271 2200

revision: January, 2004 DAVX - dig. A/V-Extender

Technical data 21

Features:

•Supports PAL + NTSC

•Supporrts FBAS and Y/C Signale with 7MHz, digital Transmission w/o Compression (ref.

CCIR 656)

•Supports (depending on device) digital Audio over optical S/P-DIF-Interface with 6MHz

Bandwith (up to 96kHz @ 64Bit Data), format transparent!

•Supports (depending on device) analogue Audio over 3.5mm stereo jack sockets (38,4kHz @

16Bit), optional Microphon Support

•Format transparent RS232-Interface up to 19200 BAUD. Supported: RxD, TxD, RTS, CTS,

DSR und DTR. Normally four of these signals are used for hardware handshaking (in addition

to TX & RX). However, because each handshaking line can support signals up to 19,200 Baud

it is possible to configure the serial interface to handle up to three simple 2-wire (Tx/Rx only)

serial links. (XON/XOFF-Handshake)

•System-Setup with Infrared Remote Control

Connectors/Cables

Pinout local and remote unit. Please use only the genuine cables for

connecting the local unit to the Audio-/Video- Equipment

Y/C In/Out connector

1 GND

2 GND

3 LUMA (Y)

4 CHROMA (C)

RS232-female/-male

1 n.c.

2 RxD

3 TxD

4 DTR

5 GND

6 DSR

7 RTS

8 CTS

9 n.c.

revision: January, 2004 DAVX - dig. A/V-Extender

22 Features:

miniDIN 4p-conn.

DB9p-fem./male

Power Supply Socket

1 GND

2 Erde

3 n.c.

4 +6VDC

GEHÄUSE Schirm

At the plug terminal on the outside of both

interface boxes a direct current power

supply with 6V/DC has to be connected. We

recommend to use our suggested p.s.u.

because GND andEARTH shouln’t be

connected. Please mount near to the

devices ferrite rings in the DC line, to

protect against electromagnetic

interferences.

Interconnection Cable: Cat5

To connect Local and Remote Units, please

use S/UTP (Cat5) cable acc. to EIA/TIA

56A or TSB 36 or Digital STP 17-03170.

Four pairs AWG 24. Pinout acc. EIA/TIA

568A (10BaseT). Screen must be

connected on both ends. To enhance EMI

resistance, both end should carry a ferrite

near to the connectors. Please be careful to

have a tension free connection!.

Hints for using CATx-Cables

The Local and Remote Units are interconnected by industry standard structured cabling

(Category 5, Cat5e, Cat6, Cat7 UTP/STP, 4-pair) terminated with RJ45 connectors. This cable is

not supplied with the Extenders. The cable used should be solid trunk cable.Stranded patch

cable will result in dramatically reduced Interconnection distances (only 60% of trunk cable).

Note: That failure to wire the twisted pairs correctly will impair the video quality dramatically and /

or prevent correct operation.

Although a single continuous length of interconnect cable is preferable, operation is possible

through multiple patch panels. However, the more patch panels the cable is routed through, the

greater the chance of video signal degradation.

Interconnection Cable: Fibre

Use for interconnecting the local and remote unit:

Multimode Modules: Two fibers 50μm or 62.5μm. E.g. I-V(ZN)H 2G50 (Inhouse patchcable) or

I-V(ZN)HH 2G62,5 (Inhouse Breakout cable) or I/AD(ZN)H 4G50 (inhouse OR outdoor Breakout

cable, stress resistant) or A/DQ(ZN)B2Y 4G62,5 (outdoor cable, stress resistant with protection

against animal biting) All notations acc. VDE specification.

revision: January, 2004 DAVX - dig. A/V-Extender

Connectors/Cables 23

4pol Hirose

Singlemode Modules: Two fibers 9μm. E.g. I-V(ZN)H 2E9 (Inhouse patchcable) or I-V(ZN)HH

2E9 (Inhouse Breakout cable) or I/AD(ZN)H 4E9 (inhouse OR outdoor Breakout cable, stress

resistant) or A/DQ(ZN)B2Y 4G9 (outdoor cable, stress resistant with protection against animal

biting) All notations acc. VDE specification.

Transceiver-Modules (Fiber Transmission)

The used transceivers are Class 1 laser products. They comply with IEC 60825-1 and FDA 21

CFR 1040.10 and 1040.11. To meet laser saftey requirements the transceivers shall be operated

within the absolute maximum ratings.

Caution

The use of optical instruments with this product will increase eye hazards! All

adjustments have been made at the factory prior to shipment of the device. No

maintenance or alteration to the device is required.

Tampering with or modifying the performance of the device will result in voided product

warranty.

Usage restrictions

The optical ports of the modules must be terminated with a optical connector or with a dust plug.

Note

Failure to adhere to the above restrictions could result in a modification that is considered an act

of “manufactoring,” and will require, under law, recertification of the modified product with the

U.S. Food and Drug Administration (ref. 21 CFR 1040.10 (i)).

Required labels

FDA IEC

Complies with 21 CFR 1040.10 and 1040.11 Class 1 Laser Product

Laser emission

revision: January, 2004 DAVX - dig. A/V-Extender

24 Transceiver-Modules (Fiber Transmission)

indication of laser

aperture and beam

Optical Characteristics (typical)

Description Multimode Singlemode

Wavelength 850 nm 1300 nm

Total output power (as defined by IEC: 50mm aperture at

10cm distance) <400μW <2000μW

Total output power (as defined by FDA: 7mm aperture at

20cm distance) <70μW <180μW

Beam divergence 12° 4°

Launched Power (Average)into multimode fiber 50μm or 62.5

μm diameter or into singlemode fiber 9μm diameter

-5 dBm (-9,5

dBm min)

-3 dBm (-11

dBm min)

average Wavelength 850 nm 1300 nm

Sensitivity (Average Power)

-20 dBm

(-17dBm

max)

-22 dBm

(-20dBm

max)

optical Budget - min.l -6,5dB -8dB

optical Budget - average -14dB -18dB

Diagnostics

at the local/remote units (LED’s)

revision: January, 2004 DAVX - dig. A/V-Extender

Diagnostics 25

Class 1 Laser Product complies

with 21 CFR 1040.10/1040.11

error Data Error (red LED)

off: no communication error

slow blinking: one or some few communication errors occurred

during the last 60 minutes

fast blinking a lot of communication errors occurred

during the last 60 minutes.

(60 minutes after the last communication error occured, the error counter is cleared

automatically)

ok Data Link (green LED)

blinking: no connection

continously on: connection okay

power on Display Power Status (green LED)

off no power or internal failure

on power ok, device ok

IR Display Data Transfer from IR Control

Blinking Data Transfer from IR Control (while pressing a key)

Getting Started

The DAVX Extender consists of a Local and a Remote Unit interconnected by a fibre cable (2

fibres) or a single structured cable. The Local Unit is connected to the output of your video-/audio

source. The monitor and speakers are connected directly to the Remote Unit. Bidirectional

devices are local and remote unit at the same time. Local and remote unit are powered by a

power supply. Please remind, that all setup processes have to be done at the remote unit.

Exception: Cat5 devices with digital audio must be setup for Video Source and Video Format at

the local unit.

Connecting Up

•Switch off your devices and power up the Local/Remote Unit by connecting the mains adapter

and switching it on. Only use the mains adapter supplied.

•Connect the local unit to the Video-/Audio- Source, the remote unit to the Video-/Audio- Sink

and interconnect the devices with the Fibre-/Cat5- Cable.

•Power on your Video-/Audio- Source, your Video-/Audio- Sink and check the data transfer.

Check that the IR Control functions.

•Check that the Data Link LED on both units stays illuminated and the Data Error LED does

not blink..

We recommend, that the complete system is tested in one room before permanent

installation. If a long interconnect cable is not available, use a patch lead to test basic unit

operation with your PC.

All configuration and tuning is carried out using the IR Control at the Remote Unit. Setting up

bidirectional devices, it is always this channel to be updated, which is displayed at the attached

screen. Here you modify settings and parameters.

revision: January, 2004 DAVX - dig. A/V-Extender

26 Getting Started

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Ihse Estensione

Ihse

Ihse kvm-tec FLEXLINE SMARTflex Manuale utente

Ihse

Ihse SDMX/S2 Manuale utente

Ihse

Ihse K472 Series Manuale utente

Ihse

Ihse kvm-tec FLEXLINE SMARTflex KT-6011 Manuale utente

Ihse

Ihse Draco vario DisplayPort 1.1 Scheda tecnica

Ihse

Ihse kvm-tec master flex 6022 Manuale utente

Ihse

Ihse K437-1W Scheda tecnica

Ihse

Ihse KVM-TEC ScalableLine Full HD Manuale dell'operatore

Ihse

Ihse Draco vario DisplayPort 1.1 483 Series Manuale utente

Ihse

Ihse Draco compact DVI 477 Series Manuale utente

Ihse

Ihse KVM-TEC ScalableLine 4K/5K Manuale dell'operatore

Ihse

Ihse K487 Series Manuale utente

Ihse

Ihse 490 series Manuale utente

Ihse

Ihse DXXi K472-SSH Scheda tecnica

Ihse

Ihse 474 Series Manuale utente

Ihse

Ihse kvm-tec MAXflex MA Manuale utente

Ihse

Ihse kvm-tec MAXflex KT-6024L CPU/LOCAL Manuale dell'operatore

Ihse

Ihse Draco vario DVI Manuale utente

Ihse

Ihse K456-1W Scheda tecnica

Ihse

Ihse kvm-tec MASTERflex MV1 6012 Istruzioni operative originali

Ihse

Ihse Draco vario IP CPU Manuale utente

Ihse

Ihse Draco Scheda tecnica

Ihse

Ihse Kvm-Tec KT-6935L Manuale utente

Ihse

Ihse Draco vario ultra DisplayPort 1.2 Manuale utente

Manuali Estensione popolari di altre marche

SY HDBT-60T Manuale utente

Appsys ProAudio

Appsys ProAudio ADX-16 Manuale utente

Atlona

Atlona RS232 Manuale utente

IDK

IDK OPF-TH1000-A Manuale utente

Enable-IT

Enable-IT 824WP Manuale utente

Worx

Worx Landroid RadioLink WA0864 Scheda tecnica

TP-Link

TP-Link TL-WA730RE Manuale utente

Camplex

Camplex CMX-HDMI-SFPL Manuale utente

SC&T

SC&T HE03-4K Manuale utente

Marmitek

Marmitek MegaView70 Manuale utente

Samsung

Samsung SCS-26UC4 Manuale utente

Foxun

Foxun SX-GES24 Manuale utente

MuxLab

MuxLab 500771 Manuale utente

foxunhd

foxunhd SX-AEX01 Manuale utente

TERK Technologies

TERK Technologies LFIRX2 Manuale utente

Devolo

Devolo Audio Extender Manuale

Edimax

Edimax EW-7438RPn V2 Manuale utente

Shinybow USA

Shinybow USA SB-6335T5 Manuale utente