Ikan TRD Beholder MS1 Manuale utente

What’s Included

QUICKSTART GUIDE

1 x Stabilizer

1 x Battery Holder

1 x Battery Cap

1 x Quick Release Plate

1 x USB LED Light

1 x Adapter Plate

1 x Micro USB Cable

2 x ¼”-20 Screw

3 x 18650 Batteries

MS1

Beholder Camera Gimbal

www.ikancorp.com 713.272.8822

CHECKED BY

Page 1

TRD Beholder®MS1 Camera Stabilizer

Specifications:

Height: 268 mm / 10.5 in.

Length: 168 mm / 6.6 in.

Width: 123 mm / 8 in.

Weight w/o Battery: 641 g / 1.4 lb.

Weight w/ Battery: 778 g / 1.7 lb.

Unit w/ Packaging: 1520 g / 3.4 lb.

Packaging Dimensions:

390x200x100mm / 15.4 x 7.9 x 3.9 in.

Range of Motion: 90-180°

Yah: 355°

Pitch: 355° ± 180°

Roll: 355° ± 60°

Battery Life: 3 hours

Electronics:

8-Bit board 2.40b7: 3-Axis Stabilizer gyro system

Kit Includes:

Maximum Supported Camera Weight

850 g / 1.9 lb.

Supported Camera Models: Sony A7S,

NEX series, Panasonic DMC, GH4,

BMPCC, RX100, A6000, Canon G7, A7ii,

and more.

Battery: Three 3.7v Li-Ion 18650 2600mAH

P/N:MS1

1/4”-20 Screw 1/4”-20 Screw

Adapter Plate

Battery Holder

USB LED Light

Quick Release Plate

3 x Batteries (18650)

Stabilizer

Yaw

Micro USB Cable

Battery Cap

2 -3 Hrs

Page 2

1. Introduction

The Beholder MS1 Camera Stabilizer is designed to support professional videographers

of all levels. The stabilizer is easy to use and small enough to travel with. The Beholder

MS1 Stabilizer is intuitive and offers a greater range of camera movement.

2. Battery Setup and Charging

A. Battery Setup

a. Install batteries positive side up into battery holder.Connect the Micro USB cable

to the Battery Holder Micro USB port. Connect USB cable to

1.5-2 amp power supply.

b. Battery charging time 4-5 hours.

c. Green light means fully charged. Red light means charging.

Flashing Red and Green lights mean almost fully charged.

d. WARNING: using a charger that does not support 1.5-2 amps will result in

batteries failing to charge.

B. Battery Holder

a. Battery Holder positive side up.

b. Insert Battery Holder into handle, positive side first.

c. Screw on battery cap and make sure the cap is secured snuggly.

Page 3

3. Camera Setup and Balancing

A. Attach the quick release plate as shown with the longest slide pointing out

towards the direction of the lens. Snuggly tighten the camera screw.

B. Attach the camera with plate to stabilizer. Adjust the camera’s position so that the

gimbal remains level.

C. Adjust the left-right balance of the camera. Small adjustments maybe needed.

D. Adjust the front and rear balance. Once gimbal is balanced, tighten the quick release

lock. If the camera does not balance perfectly, don’t worry; the MS1 will usually be

able to maintain stability.

123

89 10

456 7

E. Installation for small cameras

Cameras less than 400 g such as Sony NEX5R and BMPCC will need an adapter

plate. The adapter plate will allow cameras that cannot mount properly to be

mounted on the gimbal.

Installation steps:

1. Put the adapter plate on the camera,then tighten the screw.

2. According to your camera select an appropriate mounting position.

3. Check the position of the adapter plate, ensure the camera does not come in

contact with the gimbal.

12 3

45 6 7

8 9 10

Page 4

4. How to Use

A. To start the stabilizer: with the camera and gimbal level, place on a flat surface at

90 degrees, and then press the power button.

Note: Starting the stabilizer in a position other than 90 degrees will result in

performance issues.

The correct way to start The wrong way to start

B. Joystick mode selection

a. Press once for Lock Mode, which mode makes the stabilizer hold a position.

b. Press again to change to Follow Mode, which makes the stabilizer follow the

pan and tilt of your hand.

c. To calibrate the gyro, press and hold the joystick for 3 seconds. The gyro

controls the horizontal level. During calibration the MS1 must not be touched

and the gimbal must be level.

Page 5

Use the joystick to pan and tilt the camera.

C .Battery Status

Green light means normal. Red light

means low battery. Flashing red

light means batteries need to be

charged. Note: the MS1 will shut

down to protect the batteries.

5. Other Features

A. The stabilizer can be mounted to a tripod, selfie stick, and more.

B. The LED USB light is great for shooting at night.

C. Charge a cell phone from the stabilizer. Note: stabilizer must be off.

6. Supported Cameras.

Sony A7S, NEX series, Panasonic DMC, GH4, BMPCC, RX100, A6000, Canon

G7x, A7ii, and more.

Page 6

7. Shooting Angle Range

Roll: 45°± 45°

Tilt: 45°, 90°

The following angles are not possible.

8. Attention

A. If the stabilizer needs to be calibrated, place the MS1 on a flat surface. Make sure

the camera is balanced on the gimbal. Press and hold the joystick button for 3

seconds. If balance is not attained, repeat the calibration steps.

B. USB Ports:

The USB located on the handle is a 5v / 0.5A power output.

The Micro USB located on the handle is for remote control.

The Mini USB located on the gimbal is for accessing the 8-Bit board PID

settings through Simple BGC 8-Bit 2.40b7.

Beholder® is the licensed trademark of TRD Beholder.

Learn More

More dynamic information at ofﬁcial website: www.ikancorp.com

Support

Contact email: [email protected]

WARNING!

This product comes from the factory tuned and ready to use. It is NOT meant

to be user-serviceable, accessing and changing software settings and/or tuning

settings will void warranty.

CONDITIONS OF WARRANTY SERVICE

• Free service for one year from the day of purchase if the problem is caused by manufacturing errors.

• The components and maintenance service fee will be charged if the warranty period is expired.

Free Service will not be Provided in the Following Situations:(*Even if the product is still within the warranty period.)

• Damage caused by abuse or misuse, dismantling, or changes to the product not made by the company.

• Damage caused by natural disaster, abnormal voltage, and environmental factors, etc.

Altri manuali per TRD Beholder MS1

Indice

Altri manuali Ikan Accessori per fotocamere

Manuali Accessori per fotocamere popolari di altre marche

Viltrox

Viltrox EF-NEX Istruzioni per l'installazione

Calumet

Calumet 7100 Series CK7114 Manuale utente

Ropox

Ropox 4Single Series Manuale utente

Cambo

Cambo Wide DS Digital Series Istruzioni operative

Samsung

Samsung SHG-120 Manuale utente

Ryobi

Ryobi BPL-1820 Manuale operativo

Aegis

Aegis ABL-36020P Manuale utente

Pentax

Pentax Data Back Fc Manuale utente

Fantasea

Fantasea EyeGrabber F Series Manuale utente

Honeywell

Honeywell HDZ20HD Manuale utente

EGO

EGO BA1400T Manuale utente

Sima

Sima SRW-62 Manuale utente

Shape

Shape A7SSMKIT Manuale utente

Slide Kamera

Slide Kamera HST-2 Manuale utente

Power works

Power works 2902613 Manuale utente

SES

SES SE-2047-2 Manuale utente

Olympus

Olympus PT-EP05L Manuale utente

Starlite

Starlite OctoDome nxt Manuale utente