Ikelite 6148.72 Manuale utente
Product Registration
Please register your product at ikelite.com within 15 days of purchase.
Our product registration database is the best way for us to contact you
in the event of a product update.
Underwater Housing for Canon SX720 HS
Product Number 6148.72
2
About this Product
Thank you for your purchase of Ikelite equipment. Please read this
instruction manual completely before attempting to operate or dive
with this product. Please visit ikelite.com to register your product
to receive information on any updates or notices pertaining to your
equipment.
Included in the Box
• Housing
• Port Cover
• Accessory Packet including 1cc Silicone Lubricant
Specifications
• 200 ft (60m) depth rating
• Controls for all camera controls except Wi-Fi Button and Framing
Assist - Seek Button
• Near neutral buoyancy in fresh water
• 1/4-20 thread tray mounting with 3-inch (76mm) spacing
• Weight 2.8 lb (1.3 kg)
• Dimensions 5.0 x 6.3 x 6.8” (12.7 x 15.0 x 17.3 mm)
• 3.9 inch diameter glass lens port
3
Important Notices
»To prevent salt build-up and sticking controls, submerge the
empty housing in clean, freshwater. Operate the controls
several times each while underwater to ush out any residue.
»Never leave a housing in a rinse tank, even if it is the only
system in the tank. Most catastrophic oods happen when the
user walks away from a housing while it is in the rinse tank.
»Do not use alcohol, cleaning agents, spray lubricants, Rain-X,
or other solvents on the housing or lens port. Use of an
incompatible chemical compound can damage the plastic and
o-rings, and may result in leaking.
Accessory Port
»Do not remove the Accessory Port Hole Plug unless you are
installing a compatible accessory.
Your housing features an Accessory Port which may be used for
attachment of factory optional or aftermarket housing accessories.
The Accessory Port is 1/2-20 threaded.
Visit ikelite.com for information on optional accessories.
4
Contents
Product Registration 1
About this Product 2
Included in the Box 2
Specications 2
Important Notices 3
Accessory Port 3
Getting to Know Your Housing 5
Getting to Know Your Housing - continued 6
Installing an Accessory in the Accessory Port 7
Setting Up Your Camera 7
Pre-Installation Checklist & Initial Camera Settings 7
Setting Up Your Housing 8
Opening the Housing 8
Inserting the Camera 8
Closing the Housing 9
Attaching a Fiber Optic Strobe 10
Zoom function 11
Final Check 11
Entering the Water 11
Maintenance 12
Post-Dive 12
Travel and Storage 12
Spare Parts 13
Troubleshooting 13
Limited Warranty 15
Service and Repairs 15
Contact Us 16
5
Getting to Know Your Housing
Tray Mounts
Lens Port
Fiber Optic Ports
Lid Snap
Accessory Port
Hole Plug
Power Button ON/OFF
Zoom Lever
Shutter Button
Movie Button
6
Getting to Know Your Housing - continued
MENU
INFO
O-Ring
Lanyard
Camera Mounting Tray
Camera Mounting Plate
Lid Hook
Mode Dial
MENU
INFO
Control Dial
FUNC./SET
Single Erase/
Down Button
UP Button
7
Installing an Accessory in the Accessory Port
»Do not remove the Accessory Port Hole Plug unless you are
installing a compatible accessory.
1. Remove the Hole Plug using an 11/16” open end wrench.
2. Check the accessory tting o-ring sealing area. Check o-ring and
housing o-ring sealing area. All should be clean and free of hair,
sand, or other debris.
3. Lightly lubricate o-ring with Ikelite lubricant. Use ONLY Ikelite
lubricant. Other manufacturer lubricants can cause the o-ring to
swell.
4. Carefully screw in and tighten accessory tting. The accessory port
features a 1/2-20 threaded hole. Make sure your tting is the same
thread pattern. DO NOT cross-thread. DO NOT overtighten.
5. After installing an accessory, pressure test the housing by diving
without a camera inside.
NOTICE: Your Ikelite housing warranty DOES NOT extend
to cover the attachment of aftermarket housing accessories by
3rd parties. Warranty DOES cover factory optional accessories
attached by certied Ikelite service technicians.
Setting Up Your Camera
Pre-Installation Checklist & Initial Camera Settings
1. Insert a fully charged camera battery.
2. Insert a properly formatted memory card.
3. Set Mode Dial to “M” Manual. This will allow you to adjust aperture
and shutter speed settings to suit your shooting situation.
8
4. Set AF-assist beam to “OFF” and ISO to “200.”
5. Set Red-Eye Lamp to “OFF.”
Once underwater, camera functions can be adjusted for each shooting
situation.
Setting Up Your Housing
Opening the Housing
1. Push the lid snap lock forward and start to lift the curved end away
from the housing.
2. Lid snaps are designed to provide enough force to compress the
o-ring for a proper seal. Keep rm pressure against the lid snap
while lifting it away.
Lid Snap Lock
3. Repeat with remaining lid snap.
4. Remove the housing back.
Inserting the Camera
1. Remove any lanyard or neck strap attached to the camera.
2. Remove the camera Mounting Plate from the housing.
9
3. Line the mounting screw up with the camera’s tripod socket. Use a
coin or at head screwdriver to tighten the Mounting Plate to the
camera.
Mounting
Plate
BOTTOM
SIDE
Mounting screw Camera tripod
socket
FRONT
4. Pull out on the housing control knobs to move them out of the way.
5. Insert the Mounting Plate into the slot on the inside bottom of the
housing. Push the camera all of the way forward until the back of
the Mounting Plate is ush with the back of the housing mount.
6. Pop up the ash before installing the camera into the housing
when triggering an external strobe. Once the camera is closed in
the housing, the ash CANNOT be raised.
Closing the Housing
1. Make sure the o-ring is clean and in its proper location on the back
of the housing. The main o-ring does not require lubricant to make
a seal.
2. Place the back onto the housing front.
3. Make sure no controls or wires are interfering with the o-ring or the
back of the housing.
4. Place each lid snap into the corresponding hook on the housing
back.
10
5. Push the lid snaps toward the housing until they are at against the
housing and the lock has engaged. Close opposing lid snaps at the
same time.
6. Check the o-ring seal. The o-ring should form a uniform, solid line
around the back of the housing. There will be a small, even gap
around the housing between the housing back and the housing
front.
Attaching a Fiber Optic Strobe
1. Check the end of the ber optic cord to ensure that it is clean and
smooth.
2. Ensure that the Fiber Optic Cord O-ring is in place. This o-ring
does not provide waterproong, however it does keep the ber optic
cord in place.
3. Attach one end of the ber optic cord into one of the ber optic
ports on the front of the housing. The connector is a press-t into
the ber optic port.
O-ring
Fiber Optic Cord
4. Attach the other end of the ber optic cord to a compatible strobe.
5. Set the strobe to the appropriate setting based on manufacturer
recommendations.
6. Turn the camera on.
7. Turn the strobe(s) on.
Indice
Altri manuali Ikelite Accessori per fotocamere
Ikelite
Ikelite 6116.11 Manuale utente
Ikelite
Ikelite 69531 Manuale utente
Ikelite
Ikelite Wide Angle Port M67 Guida rapida
Ikelite
Ikelite 200DLM Manuale utente
Ikelite
Ikelite 6950.53 Manuale utente
Ikelite
Ikelite 6038.82 Manuale del proprietario
Ikelite
Ikelite 6282.53 Manuale del proprietario
Ikelite
Ikelite 6871.06 Manuale utente
Ikelite
Ikelite 6280.30 Manuale del proprietario
Ikelite
Ikelite Olympus SP-350 Manuale operativo e di manutenzione
Ikelite
Ikelite Nikon L2 Manuale utente
Ikelite
Ikelite 6801.71 Manuale utente
Ikelite
Ikelite 6132.51 Manuale utente
Ikelite
Ikelite 6183.33 Manuale utente
Ikelite
Ikelite 6801.70 Manuale utente
Ikelite
Ikelite 6154.48 Manuale utente
Ikelite
Ikelite 200DLM/A Manuale utente
Ikelite
Ikelite SLR-DC Housing Manuale utente
Ikelite
Ikelite 69621 Manuale utente
Ikelite
Ikelite Canon Elph 340 HS Manuale del proprietario
