Ikelite 6910.61 Manuale utente

Product Registration

Please register your product at ikelite.com within 15 days of purchase.

Our product registration database is the best way for us to contact you

in the event of a product update.

200DLM Underwater Housing for Sony Alpha A6000

Product Number 6910.61

About this Product

Thank you for your purchase of Ikelite equipment. Please read this

instruction manual completely before attempting to operate or dive

with this product. Please visit ikelite.com to register your product to

receive information on any updates, notices, or recalls pertaining to

your equipment.

Included in the Box

• Housing

• Waterproof bulkhead cap

• Silicone lubricant

Important Notices

»This housing requires a compatible Lens Port for waterproof

operation. The housing is not waterproof without a Lens Port

attached.

»To prevent salt build-up and sticking controls, submerge the

empty housing in clean, freshwater. Operate the controls

several times each while underwater to ush out any residue.

»Never leave a housing in a rinse tank, even if it is the only

system in the tank. Most catastrophic oods happen when the

user walks away from a housing while it is in the rinse tank.

»Do not use alcohol, cleaning agents, spray lubricants, Rain-X,

or other solvents on the housing or lens port. Use of an

incompatible chemical compound can damage the plastic and

o-rings, and may result in leaking.

Accessory Port

»Do not remove the Accessory Port Hole Plug unless you are

installing a compatible accessory.

Your housing features one 1/2-20 threaded Accessory Port which

may be used for attachment of factory optional or aftermarket housing

accessories. Visit ikelite.com for an updated list of factory optional

accessories.

Contents

Product Registration 1

About this Product 2

Included in the Box 2

Important Notices 3

Accessory Port 3

Getting to Know Your Housing 5

Setting Up Your Camera 7

Pre-Installation Checklist & Initial Camera Settings 7

Setting Up Your Housing 8

Opening the Housing 8

Inserting the Camera 8

Attaching the Hotshoe 9

Closing the Housing 10

Attaching the Lens Port 10

Final Check 11

Entering the Water 11

Setting Up An External Strobe 12

About the Built-In Flash 12

About Sync Cords 12

Attaching a Sync Cord 13

About Fiber Optic Cords 14

Attaching a Fiber Optic Cord 14

Maintenance 15

Post-Dive 15

Travel and Storage 15

Troubleshooting 16

Limited Warranty 18

Service and Repairs 19

Getting to Know Your Housing

Shutter

button

Power ON/OFF

Custom 1 (C1)

Electrical

bulkhead

Fiber optic ports

Tray mounts Lens port

mount

Lid

snap

Lens

release

Accessory Port

Hole Plug

START/STOP

DISP

ISO

ART/STOP

DISP

ISO

O-Ring Control dial

Camera

Mounting Plate

AE/MF/

AEL

Flash pop up

Custom 2 (C2)

Playback

Mode dial

Start/Stop

Set Button

Control wheel

Setting Up Your Camera

Pre-Installation Checklist & Initial Camera Settings

1. Insert a fully charged camera battery.

2. Insert a properly formatted memory card.

3. Set Red Eye Reduction and AF Illuminator to “Off.”

4. Set Focus Mode to “AF-S Single Shot and Focus Area to “Center.”

5. Set ISO to ISO AUTO or a specic ISO setting. Do not use ISO

AUTO Multi Frame NR setting if using a ash. This setting will

prevent the ash from ring.

ISO

Multi Frame NR

ISO

AUTO

100

125

160

200

6. Set Metering Mode to “Center.”

7. Set Smile/Face Det. to “OFF.”

8. Set Eye-Start AF to “OFF” if illuminated in Menu screen.

9. Set FINDER/MONITOR to “Monitor.”

10. Set Power Save Start Time to “5 Min.”

Setting Up Your Housing

Opening the Housing

1. Push the lid snap lock forward and start to lift the curved end away

from the housing.

2. Lid snaps are designed to provide enough force to compress the

o-ring for a proper seal. Keep rm pressure against the lid snap

while lifting it away.

Lid Snap Lock

3. Repeat with remaining lid snaps.

4. Remove the housing back.

Inserting the Camera

1. Remove any lanyard or neck strap which may be attached to the

camera.

2. Check to see whether the camera’s lens will t through the port

opening of the housing. If not, the lens will need to be removed

from the camera body and re-attached AFTER the camera body is

installed in the housing.

3. Remove the camera Mounting Plate from the housing.

4. Line up the Mounting Screw with the Camera Tripod Socket. Use a

coin or at head screwdriver (preferred) to tighten the mounting

plate to the camera.

1/4-20 Mounting Screw

1/4-20 Threaded Hole

Camera Tripod Socket

Camera Mounting Plate

5. Pull out on the housing control knobs to move them out of the way.

6. Insert the Mounting Plate into the slot on the inside bottom of the

housing. Push the camera all of the way forward until the back of

the Mounting Plate is ush with the back of the housing mount.

Attaching the Hotshoe

1. Make sure the contacts are clean.

2. Slide the hotshoe onto the camera with the LOCK marking towards

the back of the camera.

3. Push the hotshoe forward until it is unable to go any farther. The

hotshoe must be pushed all of the way forward to make proper

contact with the camera and provide TTL operation.

4. Rotate the locking ring at the hotshoe base clockwise until snug.

Closing the Housing

1. Make sure the o-ring is clean and in its proper location on the back

of the housing. The main o-ring does not require lubricant to make

a seal.

2. Place the back onto the housing front.

3. Make sure no controls or wires are interfering with the o-ring or the

back of the housing.

4. Place each lid snap into the corresponding hook on the housing

back.

5. Push the lid snaps towards the housing until they are at against

the housing and the lock has engaged. Close opposing lid snaps at

the same time.

6. Check the o-ring seal. The o-ring should form a uniform, solid line

around the back of the housing. There will be a small, even gap

around the housing between the housing back and the housing

front.

Attaching the Lens Port

A compatible lens port is required for waterproof operation.

Never submerge the housing without a lens port attached.

1. Lightly lubricate the o-ring on the port base. When properly

lubricated, the o-ring should have an even, slightly shiny

appearance. Wipe off any excess lubricant. Lubricant prevents the

o-ring from rolling or extruding; it is not a sealing mechanism.

2. If using a gear sleeve, place it on the port base with the teeth side

outwards.

3. Slide the lens port onto the housing port base and press evenly

down towards the housing until it stops. There should be a very

thin, even gap between the bottom of the port and the housing

front.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Ikelite Accessori per fotocamere

Ikelite

Ikelite Olympus Mju760 Manuale utente

Ikelite

Ikelite 6245.07 Manuale utente

Ikelite

Ikelite 6047 Manuale del proprietario

Ikelite

Ikelite 6842.35 Manuale utente

Ikelite

Ikelite 4077.67 Scheda tecnica

Ikelite

Ikelite SX210 IS Manuale utente

Ikelite

Ikelite 4103.51TTL Manuale utente

Ikelite

Ikelite 9295.02 Scheda tecnica

Ikelite

Ikelite 6085 Manuale del proprietario

Ikelite

Ikelite Olympus C-8080 Manuale utente

Ikelite

Ikelite 6843.72 Manuale utente

Ikelite

Ikelite DSC-W5 Manuale utente

Ikelite

Ikelite 75344 Manuale utente

Ikelite

Ikelite 6170.30 Manuale utente

Ikelite

Ikelite Nikon 7600 Manuale utente

Ikelite

Ikelite 6148.70 Manuale utente

Ikelite

Ikelite 6116.15 Manuale utente

Ikelite

Ikelite 200DLM/B Manuale utente

Ikelite

Ikelite 6801.32 Manuale utente

Ikelite

Ikelite 6194 Manuale utente

Ikelite

Ikelite ALL Manuale utente

Ikelite

Ikelite Digital Housing Manuale utente

Ikelite

Ikelite 6182.71 Manuale utente

Ikelite

Ikelite 6961.85 Manuale utente

Manuali Accessori per fotocamere popolari di altre marche

Viltrox

Viltrox EF-NEX Istruzioni per l'installazione

Calumet

Calumet 7100 Series CK7114 Manuale utente

Ropox

Ropox 4Single Series Manuale utente

Cambo

Cambo Wide DS Digital Series Istruzioni operative

Samsung

Samsung SHG-120 Manuale utente

Ryobi

Ryobi BPL-1820 Manuale operativo

Aegis

Aegis ABL-36020P Manuale utente

Pentax

Pentax Data Back Fc Manuale utente

Fantasea

Fantasea EyeGrabber F Series Manuale utente

Honeywell

Honeywell HDZ20HD Manuale utente

EGO

EGO BA1400T Manuale utente

Sima

Sima SRW-62 Manuale utente

Shape

Shape A7SSMKIT Manuale utente

Slide Kamera

Slide Kamera HST-2 Manuale utente

Power works

Power works 2902613 Manuale utente

SES

SES SE-2047-2 Manuale utente

Olympus

Olympus PT-EP05L Manuale utente

Starlite

Starlite OctoDome nxt Manuale utente