iLoq D5S.(A).SB Series Guida all'installazione
Page 1 of 16
D5S.XXX(A).SB
D5S.XXX(L).SB
EUROPROFILE LOCK CYLINDER
MOUNTING AND CARE INSTRUCTIONS
USER GUIDE
Page 2 of 16
TABLE OF CONTENTS
1.
BEFORE INSTALLING ................................................................... 3
2.
AFTER INSTALLATION .................................................................. 4
3.
CARE .............................................................................................. 4
4.
INSTALLATION OF ILOQ D5S.1XX SERIES ................................. 4
5.
INSTALLATION OF ILOQ D5S.2XX SERIES ................................. 5
6.
INSTALLATION OF ILOQ D5S.3XX SERIES ................................. 8
7.
INSTALLATION OF ILOQ D5S.4XX SERIES ................................. 9
8.
INSTALLATION OF ILOQ D5S.7XX SERIES ............................... 10
9.
REMOVING AND INSTALLING THE O TSIDE KNOB ................ 11
10.
CYLINDER EXTENSIONS ............................................................ 13
10.1
One side .................................................................................................13
10.2
Both sides ...............................................................................................15
10.3
Long neck ...............................................................................................15
11.
GENERAL NOTES ........................................................................ 16
Page 3 of 16
1. BEFORE INSTALLING
1. These instructions should be carefully followed during installation. These instructions and any
maintenance instructions should be assed on by the installer to the user.
2. iLOQ D5S cylinders must be installed and used carefully without excessive force.
3. The roduct should not be modified in any way exce t in accordance with the modifications
described in these instructions.
4. Where the D5S cylinder is manufactured in more than one size it is critical that the correct size is
selected.
5. Care should be taken to ensure that any seals or weather-stri ing fitted to the com lete door
assembly, does not inhibit the correct o erations of D5S cylinder.
6. Care should be taken to ensure that no rojection of the D5S cylinder and associated arts, can
revent the door swinging freely.
7. All com onents necessary for the s ecific installation should be fitted in order to ensure com liance
with EN 15684 standard.
8. The cylinder must roject less than 1 mm on outside of the door to ensure ro er o eration.
9. No liability is acce ted for damage to the doors or com onents due to incorrect installation.
10. Before fitting D5S cylinder to a fire/smoke resisting door, the fire certification should be examined,
to ensure conformity.
11. To extend the cylinder length use only the associated D5 cylinder extensions (AD5.Exx).
12. It is not allowed to uninstall res . demount the anti- anic mechanism because due to that the
mechanism and functionality of the anic functionality can not be guaranteed anymore.
13. In the case the anic mechanism of the anic mortise locks can be blocked or influenced in a
negative way by the cylinder cam, it is mandatory to install the anic cylinder (D5S.7xx). The use of
the other cylinder ty es (D5S.1xx/2xx/3xxx/4xx/5xx etc.) are only allowed if the lock do not need a
s ecific cam osition res . the cam could not block the anic functionality. Please double-check the
letter of conformity of the mortise lock manufacturers.
14. When used in combination with anic locks, it is essential to ensure after installation that all arts
of the lock are in an o erational condition and that the anic function of the mortise lock is guaranteed.
15. The long neck versions are s ecially develo ed for doors where the Euro- rofile cut out is not
existing inside the door frame and only a round hole is ossible to find.
16. To meet the German VdS (VdS Schadenverhütung GmbH) requirements class CZ+ on burglary
threatened doors use D5S.XX0A.SB high security cylinder installed with a VdS a roved security lock
furniture of class B or C.
17. The cylinders may only be used for the ur ose of o ening and locking doors; other use is not
ermitted.
18. We reserve the right to make modifications or further technical develo ments without further
notice.
19. If there are any deviations from the contents in foreign language versions of the documentation,
the English original shall a ly in case of doubt.
Page 4 of 16
2. AFTER INSTALLATION
Test the cylinder functionality after installation to ensure that it does not revent the lock case from
working ro erly.
3. CARE
After 5-10,000 usages, clean contact rolls lightly with lint-free cotton ad. S ray small amount of high-
quality lock oil i.e. CRC lock oil (with PTFE) onto contact rolls.
In the case the cylinder is not working in an a ro riate way anymore, we recommend cleaning the
cylinder with e.g. com ressed air s ray or similar.
4. INSTALLATION OF ILOQ D5S.1XX SERIES
A. Ensure the cam is ointing downwards and slide lock cylinder through the lock case.
B. Fix cylinder into lock case by iLOQ fixing screw (A10.64, art of the delivery), use tightening
torque 0.9 ...1.1 Nm. If necessary, cut the screw to the correct length.
(calculation screw length: L = backset + 10 mm).
The screw has cutting grooves to make the cutting easier.
C. Make sure the cylinder frame is a maximum of 1.0 mm from the door leaf or escutcheon.
B.
A.
C.
Page 5 of 16
5. INSTALLATION OF ILOQ D5S.2XX SERIES
A. Remove knob from the other side of the cylinder as described in cha ter 9.
Page 6 of 16
B. Removing and installing the Outside
knob
.
C. Ensure the cam is ointing downwards and slide lock cylinder through the lock case.
D. Fix cylinder into lock case by iLOQ fixing screw (A10.64, art of the delivery), use tightening
torque 0.9 … 1.1 Nm. If necessary, cut the screw to the correct length (calculation screw
length: L = backset + 10 mm).
The screw has cutting grooves to make the cutting easier.
E. Install the ower knob as described in cha ter 9.
Page 7 of 16
F. Removing and installing the Outside
knob
.
G. Make sure the cylinder frame is a maximum of 1.0 mm from the door leaf or escutcheon
D.
C.
B.
E.
Page 8 of 16
6. INSTALLATION OF ILOQ D5S.3XX SERIES
A. Loosen screw from thumb turn with 2 mm Allen key, turn them counterclockwise, that it is
ossible to remove the knob (but do not screw them out com letely).
B. Ensure the cam is ointing downwards and slide lock cylinder through the lock case.
C. Make sure the cylinder frame is a maximum of 1.0 mm from the door leaf or escutcheon.
D. Fix cylinder into lock case by iLOQ fixing screw (A10.64, art of the delivery), use tightening
torque 0.9...1.1 Nm. If necessary, cut the screw to the correct length (calculation screw length:
L = backset + 10 mm).
The screw has cutting grooves to make the cutting easier.
E. Thum turn knob in lace.
F.
Tighten screw by turning the screw clockwise. Use tightening torque 1.5 Nm.
A.
B. C.
D. E.
F.
G.
Page 9 of 16
7. INSTALLATION OF ILOQ D5S.4XX SERIES
A. Ensure the cam is ointing downwards and slide lock cylinder through the lock case.
B. Fix cylinder into lock case by iLOQ fixing screw (A10.64, art of the delivery), use tightening
torque 0.9 ...1.1 Nm. If necessary, cut the screw to the correct length (calculation screw length:
L = backset + 10 mm).
The screw have cuting grooves to make the cutting easier.
C. Make sure the cylinder frame is a maximum of 1.0 mm from the door leaf or escutcheon.
B.
A.
C.
Page 10 of 16
8. INSTALLATION OF ILOQ D5S.7XX SERIES
A. Ensure the cam is ointing downwards and slide lock cylinder through the lock case.
B. Fix cylinder into lock case by iLOQ fixing screw (A10.64, art of the delivery), use tightening
torque 0.9 ...1.1 Nm. If necessary, cut the screw to the correct length (calculation screw
length: L = backset + 10 mm).
C. Make sure the cylinder frame is a maximum of 1.0 mm from the door leaf or escutcheon.
B.
A.
C.
Questo manuale è adatto per i seguenti modelli
6
Indice
Altri manuali iLoq Serratura della porta
