Ilsintech Keyman S1 Manuale utente
1
I . Safety guide
II. Menu Control
1. Pop-up Menu Registration
2. Setting Auto Heat
3. Setting Errors to be Affected or Ignored
4. Menu Clearing the Record of Total Number of Electric Discharge
5. Setting the Amount of Electric Discharge to be Cleared
6. Changing Maintenance Schedule
III. Correction Menu
1. Selecting Correction Menu
2. LED Bright Menu
3. Uart Port
4. ARC Settle
5. Motor Setting
6. Check Up
12
INDEX
2
6
6
7
9
1
9
10
9
7
10
10
11
10
12
10
7
7
8
10
10
2
7. Splice data Update
IV. Maintenance
1. When an Error in Classifying SM and MM in Auto Mode Occurs
2. Eccentricity of Position of ARC Discharge
3. Abnormal Arrangement of Optical Fibers in Connection Operation
4. Occurrence of a Length Difference When Optical Fibers are Initially Placed
5. Occurrence of an Error during Booting
6. In case of High Connection Loss Rate
7. Replacing the Battery
8. Replacing the Mirror
9. Program Upgrade
This specification is applied to the maintenance and management of
released products of which versions are later than Keyman-S1 Version
3.00.
13
10
13
10
12
10
13
10
13
10
13
10
15
10
17
10
17
10
18
10
19
10
3
Keyman S1 has been designed and manufactured for convenient use in indoor
or outdoor working conditions. It is easy and simple to use, but please read
through this manual completely to avoid failures and safety accidents before
you use it. Keyman S1 is designed to easily use, but also contains potential
danger. Therefore, this manual contains all necessary instructions to assure
safe splice.
�Please keep this manual with the product all the time.
Ilsintech(Inc.) is not responsible for equipment damage and personal or
physical damage caused by improper use or modification.
Ⅰ. Safety guide
Warning
4
If an abnormal condition such as the following occurs, immediately turn off
power and disconnect the power source. Next, contact the maintenance
service personnel in Ilsintech(Inc.).
�If unusual smoke, noise or odor or unusual overheating occurs,
�If foreign substance or liquid gets inside the splicer, or
�If the splicer is dropped from a high place or suffers damage
Do not use AC power code other than the allowable power cord indicated.
Doing so may cause a fire, electric shock or injury. Use the power code
provided with S1.
Do not touch the electrodes when S1 is switched on. High voltage and High
temperature from them may cause serious shock or a burn.
Make sure that there is no dust or foreign substance inside the AC plug. Then,
Connect AC power cord to the specified charger and the outlet. Unsafe splice
may cause smoke, fire, equipment damage, serious injury or death.
5
Do not use a voltage other than the allowable power voltage indicated.
AC power supply for the specified charger is AC 100-240V, 50-60Hz.
Please check the AC power supply before using. AC power supply within the
improper range may cause electric shock, equipment damage, serious injury
or even a death. Abnormally high AC output voltage or frequency from the
generator is a common problem. Measure AC output voltage with a circuit
tester before connecting AC power cord. Regular inspection is needed
because improper high voltage or frequency from the generator may cause
serious injury, electric shock, equipment damage or death.
Do not severely pull, heat or modify the provided AC power cord. The use of
damaged power cord may cause hazardous conditions such as fire or injury.
Connect only to 3-core AC power cord. Do not connect to 2-core power cord,
cable or plug.
To reduce the risk of electric shock, do not touch the AC plug, the AC power
Warning
6
code and the splicer with wet hands.
Do not disassemble AC adapter, battery or the splicer. Any modification to
the splicer may cause a fire, electric shock or injury.
When you use external battery, see the following instructions.
�The use of improper external battery may cause smoke, equipment
damage, or in serious cases burning, injury or death.
�Do not throw the battery into a fire or a garbage dump.
�Do not charge the battery close to flames.
�Do not give severe vibration or shock to the battery.
�If the battery is not fully charged within 6 hours or green LED
lamp is not on, immediately stop charging and contact Ilsintech(Inc.)
Do not place any object on AC adapter during charging.
Only use the specified battery charger(S-1B) and the specified battery pack(S-
1B). The use of any battery pack other than the specified one may cause
smoke or fire, equipment damage, injury or death.
7
Only use the specified battery charger(S-11).
Do not use AC power other than the allowable power indicated.
Do not let battery(S-1B) or the terminal of the specified charger be short-
circuited. Excessive current flow may cause damage to the equipment and
persons.
Avoid the use of S1 in a hazardous location in which harmful gas or
flammable gas can generate. In such conditions, the electrical arc of the
fusion splicer can result in bursting or fire.
Do not use compressed gas to clean S1.
If you carry the transport case connected with a belt, first check the belt is
strong enough. The worn belt may fail to sustain the case, resulting in
Warning
8
equipment loss or injury.
Wear safety glasses for protection from glass fibers. Glass fibers may cause
serious damage to eyes or skin tissue.
Do not use the splicer in high temperature conditions. Doing so may cause
equipment loss or injury.
Do not use a splicer in high temperature conditions. Doing so may cause
equipment loss or injury.
Caution
9
During or after heating protection sleeves in the tube heater, do not touch both
parts. Injury from high temperature could occur.
Do not place S1 in unstable locations. If the equipment is dropped, injury or
equipment damage could occur.
S1 is a precision instrument. It should be handled with care and precision.
When transporting it, use its specified transport case to protect it from dust,
dust, moisture, shock and impact.
Replace the electrodes the right way.
�Only use the specified electrodes.
�Place the new electrode in the right position.
�Replace the electrodes in pairs.
Not doing so may cause abnormal arc and equipment damage or deterioration
in splice performance.
Only use ethyl alcohol (more than 96 %) to clean the splicer including object
Altri manuali per Keyman S1
2
Indice
Altri manuali Ilsintech Sistema di saldatura
