ILY Enterprise CoolCopy 3 Manuale utente



User’s Manual

CoolCopy1AL(CD-Backup)

CoolCopy 3

CoolCopy 7



























Table of Contents

Chapter 1 Introduction

................................................................4

1.1 Overview ...................................................................................4

1.2 Features ....................................................................................4

1.3 Specifications ...........................................................................4

Chapter 2 Installation Procedure

.............................................5

2.1 Controller only ........................................................….…..........5

2.2 Whole duplicator without writer installed ..….........................5

2.3 Completed duplication system ...................….........................5

Chapter 3 Key Functions and Operating Instruction

……9

Chapter 4 Function

..........................................................….......…10

4.1 Copy ................................................................…........................10

4.2 Test ....................................................................................…..…11

4.3 Test&Copy............................................................…....…........…11

4.4 Verify ....................................................................…..................11

4.5 Compare ..............................................................…...............…12

4.6 Prescan ................................................................…..................13

4.7 Disc Info ........................................................................…….....13

4.8 Select Source................................................................….........13

4.9 Image .........................................................................................14

4.9.1 Load .....................................................................................14

4.9.2 Delete Image ........................................................................14

4.9.3 Image Info .............................................................................15

4.9.4 Compare Image ....................................................................15

4.9.5 Select Partition ......................................................................16

4.9.6 Select Src Drive ....................................................................16

4.10 Edit Track ...............................................................................16

4.10.1 CD to CD Edit......................................................................17

4.10.2 CD to HD ............................................................................18

4.10.3 Play Audio Track ................................................................20

4.10.4 Close Session ....................................................................20

4.11 Setup.........................................................................................20

4.11.1 Language (optional)....................................................…......21

4.11.2 Burn Speed .........................................................................21

4.11.3 Read Speed ........................................................................21

4.11.4 Auto Start Drive ...................................................................21

4.11.5 Start up menu ......................................................................21

4.11.6 Auto Verify ...........................................................................22

4.11.7 Auto Compare ......................................................................22

4.11.8 Auto Prescan .......................................................................22

4.11.9 Eject Disc ............................................................................22

4.11.10 Burn on The Fly ................................................................23

4.11.11 Burn Mode ........................................................................23

4.11.12 Button Sound ....................................................................23

4.11.13 Device Info ....................................................................…24

4.11.14 System Info .......................................................................24

4.11.15 Quick Erase ......................................................................25

4.11.16 Full Erase ..........................................................................25

4.12 Adv Setup...................................................................................25

4.12.1 UnderRun Protect ...............................................….............25

4.12.2 Overburn ...............................................................…...........26

4.12.3 Read Error Skip............... ..................................…..…... ...26

4.12.4 Format Hard Disk ....................................................….........26

4.12.5 Verify HDD ...............................…..................................…...26

4.12.6 Burn-in.................................................…...…........................27

4.12.7 Update Firmware..........................................................….....27

4.12.8 Compare Firmware .......................................................…....28

4.12.9 H/W Diagnostic ...............................................................…..28

4.12.10 Load Default ..................................................................….28

Chapter 5 Troubleshooting

.........................................................29

Chapter 1 Introduction

1.1 Overview

People who want to create multiple copies of their CDs usually take a long time to do so. They

might not have enough CD+RW drives or they might be using their computers for some other

important tasks. The duplication process noticeably slows down a computer during the burn

process. Rather than sit at the computer for hours duplicating discs one at a time, it is much more

efficient to use a CoolCopy CD duplication system.

The Coolcopy CD Duplicator system is a standalone duplicator and does not need to be

connected to a computer. It can duplicate discs accurately and quickly. With its multi-function

LCD panel, Coolcopy CD Duplicator is easy for any user to operate. It is a cost-efficient CD-R

duplicator for audio, data, and video applications. The simple control panel is designed to provide

copy mode selection and copy operation.

1.2 Features

•Standalone IDE to IDE CD Copy controller

•2(Coolcopy1AL(CD-Backup)) / 4(Coolcopy3) / 8(Coolcopy7) / 16(Coolcopy14)

independent IDE channel

•Self system diagnostics when power on

•Supports Hard Drive image

•Auto format detection

•User friendly interface with message rich LCD display

•Fast copies supports high speed CD-RW writing mode

•Easy operation without software and training are required

•Firmware upgrade via CD-ROM

1.3 Specification

Power requirement – voltage: 5VB+/- 5%

Current: 0.5A Max.

Environment - Temperature

Operating 0˚ C to 70˚ C

Storage -20˚ C to 85˚ C

Humidity - 15% to 90%

Models: Coolcopy3/coolcopy7

Dimensions - Length: 200 mm

Width: 146.2 mm

Height: 42 mm

Connectors - 40-pin internal IDE connector

Cable (Optional) - Using ATA-66 (*Cable of length do not use longer than 46cm)

CD Format - CD-ROM (Mode1 & Mode2), CD-ROM/XA (Mode2 form1 & form2), CD-DA,

Mixed-Mode, Video CD, CD-I, Karaoke CD, Photo CD (Single & Multi-

session), CD-Extra, HFS, CD Bridge, ISO9660, CD-R, and CD-RW

Writing mode - Auto Detect (DAO, TAO)

Supported CD-ROM Drives* - EPO, TEAC

Supported CD-RW Drives* - Plextor, TEAC, Lite-On, Asus, SONY

Chapter 2 Installation Procedure

When you receive the Coolcopy CD Duplicator, the package could be packaged in the following

ways: controller only, whole duplicator without writer installed, and a complete duplication system.

2.1 Controller only

1. Before the installation, please prepare the necessary devices as following:

•CD-ROM drive

•CD-R/RW drive

•IDE case (2~10-bay chassis suggested).

•Hard drive and mobile rack (IDE-bus hard drive-Option)

•Switching power supply (300W suggested).

2. After the preparation as above and make sure that:

•All IDE devices must be in master mode.

2.2 Whole duplicator without writer installed

•Unpack the package of the duplicators.

•Prepare the CD-R/RW writers according to the recommendation list. Please check with

the supplier about compatibility issues with unlisted CD-R/RW drives.

•Assemble the duplicator according to your need.

•Make sure that the voltage setting is correct.

2.3 Completed duplication system

•Take the duplication system out of the package.

•Check the entire unit to see if there are any problems.

•Make sure that the voltage setting is correct.

•The hard drive is optional.

Hardware Connection of CoolCopy1AL (CD-Backup) without a HDD

CoolCopy1AL (CD-Backup)

Rom

Power

Hardware Connection with Hard Drive for Coolcopy3

When the system connects with the hard drive, the hard drive must connect on the IDE 0 port

with the “Master” setting and the CD-ROM must set at “Slave”.

Hardware Connection without Hard Drive for Coolcopy3

Coolcopy 3

IDE 0

Rom/HDD

Pow

IDE 3

IDE 2

IDE 1

Coolcopy 3

IDE 3

IDE 2

IDE 1

IDE 0

Rom

Pow

Hardware Connection with Hard Drive for Coolcopy7

Pow

Coolcopy 7

E 5

IDE 1

Rom/HDD

IDE

IDE 2

IDE 7

IDE 6

IDE 3

IDE 4

When the system has a hard drive connected, the hard drive must connect on IDE 0 port with

“Master” setting and the CD-ROM must set at “Slave.”

Hardware Connection without Hard Drive for Coolcopy7

Coolcopy 7

IDE 4

IDE 3

IDE 2

IDE 1

Rom

IDE 8

IDE 7

IDE 6

IDE 5

Pow

Chapter 3 Key Functions and Operating Instruction

1. LCD Display Panel: Display main functions and all messages.

2. Scroll up through menus or functions.

3. Scroll down through menus or functions.

4. Execute the function which you select.

5. Cancel the function which you select.

After turning the power on, the Coolcopy CD Duplicator will execute a self test for a few seconds.

After the self testing procedure runs, the LCD will show:

1. Coolcopy3: Coolcopy7:

Two main operation procedures

If you install a 3.5” hard disc, the operation procedures is as follows:

1. With hard drive installed

•Once duplicator detects a hard disc, it will ask if you want to format or not. A 10GB hard

disc can be divided into 10 partitions.

•Use the Select Source to set the hard drive as the target source.

•Then select which partition to store the data in function 9 “Image.”

•If there is no data stored in partition, insert a source CD into CD-ROM and use function 9-

01 Load to transmit data from CD into selected partition by pressing ENT. Different data

can be stored in different partitions.

•Switch to the Copy function by pressing the arrow button. Insert blank CD-R or CDRW

discs into the CD writers. Press “ENT” button to start copying.

CD Duplicator

1-3 ver: 1.10B

CD Duplicator

1-7 ver: 1.10T

Initialize SDRAM.....

Detect Drives.....

1. Copy

•When a Copy completes, the passed (correctly copied) CD discs will be ejected

automatically. The default is to eject automatically, but this can be changed.

•Failed discs will remain in writers. The default setting is keeping failed discs in the writers,

but this can be changed. Press the buttons on the drivers to take the failed CDs.

•During operation do not press any button, interruption will harm the device. CDs will be

damaged.

2. Without a hard drive installed

If you don’t install a 3.5” hard disc, the operation procedures will be as follows:

•Insert the master disc to CD-ROM.

•Switch to the Copy function by pressing arrow button. Insert blank CD-R or CDRW disc

into all the CD writers. Press “ENT” button to start.

•When Copy completes, the passed CDs will eject automatically. The default is to eject

automatically, but this can be changed.

•

Failed CDs will remain in the writers. The default setting is that failed CDs stay in the

writers, but you can change the setting. You need to press the “eject” buttons on the

writers to take the failed CDs.

ATA-66 Cable Layout:

Please identify two different kinds of cable before the hardware installation.

Chapter 4 Function

4.1 Copy

Use this function to copy data from a source CD directly onto blank CD discs. Before copying

make sure that the source CD is insertd into CD-ROM. If you have a HDD, make sure there is

data in your HDD partition. If you are not sure about the success of your duplication job, you can

use function 2, Test, to simulate the copying process first.

Select function 1. Put a source CD into CD-ROM and blank CD disks into CD writers. CD

rewriteable discs containing old data are usable, too.

LCD will show the process of copying

information as follows:

When copying is completed, the LCD will display as

the following information:

Discs correctly copied will be ejected automatically

Copying-24X 0%

650.0MB 74:00

Copy

OK: 03

Test & Copy

OK: 03

Altri manuali per CoolCopy 3

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali ILY Enterprise Registratore DVD

ILY Enterprise

ILY Enterprise CoolCopy 3 Manuale utente

Manuali Registratore DVD popolari di altre marche

Pioneer

Pioneer DVR-65H-S Guida all'installazione

Sony

Sony RDR-VX525 - DVDr/ VCR Combo Manuale utente

Daewoo

Daewoo DHD-4000D Manuale utente

Medion

Medion MD 40570 Manuale utente

Philips

Philips ShowView DVDR3460H Manuale utente

Sony

Sony RDR-GX355 - Tunerless DVD Recorder Manuale utente

Sony

Sony DVDirect VRD-MC3 Manuale utente

Samsung

Samsung DVD-R130/XAA Manuale utente

FUNAI

FUNAI HD-B2735 Manuale utente

Panasonic

Panasonic DMR-EH54DEG Manuale utente

Pioneer

Pioneer PRV-LX1 Manuale tecnico

Sanyo

Sanyo DRW-1000 Manuale utente

Philips

Philips DVDR610/05 Manuale utente

JVC

JVC DR-M10 Manuale utente

Samsung

Samsung SV-DVD40 Manuale utente

Philips

Philips DVDR3355 Manuale utente

FUNAI

FUNAI FDR-90E Manuale utente

LG RC298 Manuale utente