IMOU DB60-KIT Manuale utente
V1.0.0
Quick Start Guide
Video Doorbell
https://en.imoulife.com
Welcome
Thank you for choosing IMOU.
We are devoted to providing you easy smart home products. If you have problems using the
Device Safety Precautions
Read this guide carefully and keep it for future reference.
Follow all instructions for safe use and handling of the device.
Do not disassemble the device.
Use the device at temperatures fro
m -20 °C (-4
°F) to +50 °C (+122 °F).
Do not point the device directly at the sun or a source of intense light.
Periodic cleaning may be required. Use a soft dry cloth only. Do not use
any harsh, chemical-based cleaners.
Battery Safety Precautions
Only use batteries provided. Do not replace batteries by yourself.
Do not remove the battery from the doorbell.
Do not use batteries at temperatures above 60 °C (140 °F) or place batteries next to areas which may become
hot.
Keep batteries isolated from ammable or explosive materials.
Always follow local waste and recycling laws and guidelines to dispose of used batteries.
Do not use a battery if its case appears damaged, swollen, or compromised. Examples include, but are not
limited to, leaking, odors, dents, corrosion, rust, cracks, swelling, melting, and scratches.
All batteries can explode, catch re, and cause burns if it has been cut, crushed, disassembled, punctured,
incinerated, short-circuited, or exposed to water, re or high temperatures. Safely and responsibly install, use, and
dispose of batteries.
Package Contents
Doorbell
×1
Mounting Bracket
×1
Angled Bracket ×1
(15° horizontally)
Angled Bracket ×1
(5° vertically)
Wall Anchors
×4
Mounting Screws
×4
Mounting Screws
×4
Terminal Screws
×2
Extension Wires
×2
15/64" Drill Bit
×1
Wire Nuts
×3
Pin
×1
1
Tools Required
Drill
Philips-head
Screwdriver
Charging Cable
×1
Quick Start Guide
×1
Overview
2
Front View Back View
Bottom View
Lens
Motion Sensor
Microphone
Light Sensor
LED Indicator
Call Button
Speaker
Spotlight/Night Light
Micro USB Port
Power Port
Reset Button
LED Status Device Status
Operating correctly
Setup successful
Ready to set up the device
Booting/Restarting
Resetting to factory default
Network disconnected
Talking
Motion/Human detected
Calling
Solid green
Solid red
Flashing green
Solid blue
Flashing blue
Spinning blue
Flashing green
and red
O
Flashing red
Updating rmware
Power o
QR Code
Scan the QR code with Imou Life App to add the
device to your account. Please keep it well for
future use.
Function of the QR code
i
Set Up the Device
Scan the QR code below, search for "Imou Life" in the app store, or navigate to Support > Download Center in
our ocial website to download and install the app.
To ensure the best possible wireless performance, please make sure there are no obstacles and electromagnetic
interference between the device and the router.
If you already use the app, make sure that you are using the latest version.
3
i
1
Imou Life
The app will guide you through the setup process.
4
i
Reset the device: Press and hold the reset button located on the back of the device for 5 s until the LED
turns red.
Where is the device QR code: On label that was attached to the box or on the back of the device.
2
Rear Side
SSID
XXXXXX
Password
Next
Setup
Add Device
+
Done
Setup
Power the Doorbell
Ensure that the battery power is enough to turn the doorbell on, otherwise recharge the battery through the
USB port.
Option 1 Battery Powered
The doorbell can run on its own rechargeable battery power. See from page 5 for installation without wiring.
Option 2 Wire Powered
If you have existing doorbell wiring, your doorbell can get continuous power. Supply the doorbell with 12 V-24 V,
AC/DC power. See from page 8 for installation with existing wiring.
i
Install the Video Doorbell (Battery Powered)
Step 1 Mark Mounting Holes
Place the mounting bracket on the mounting surface and then use it to mark the
screw holes. Be sure to follow the "UP" direction.
5
i
How to use angled bracket
Attach one of the angled mounting wedges to the mounting bracket if you
want to adjust the angle of your doorbell for a better view. Mark the screw
position according to the oval hole.
OR
15° Left
5° Up 5° Down
15° Right
Step 2 (Optional) Install Wall Anchors
If installing on stucco, brick, or concrete, use the provided drill bit to drill holes where
marked, and then insert the included wall anchors.
For wood, drywall or soft surface, skip this step.
Step 3 Secure the Bracket
Secure the bracket to the mounting surface with a Philips-head screwdriver and supplied mounting screws. Be
sure to follow the "UP" direction on the mounting bracket. If you use an angled bracket, it must be used together
with the mounting bracket.
6
Angled
Bracket
OR
x 4 x 2
Mounting
Bracket
Mounting
Bracket
x 4
1 2
7
Step 4 Mount the Doorbell
Place the doorbell on the top tab of the mounting bracket, and then push it
into the bottom tab, until you hear it click into place.
How to detach the doorbell from the mounting bracket
How to recharge the doorbell
Insert the supplied pin into the hole at the bottom of the bracket
and push it slightly harder until the doorbell is released.
When you receive the low battery alert from
the app, please recharge your doorbell.
i
i
LED
Indicator
Charging: Flash green
Fully charged: Solid
green
5V 2A: About 3 h
5V 1A: About 6 h
Charging
Time
Altri manuali per DB60-KIT
1
Indice
Altri manuali IMOU Sistema di interfono
