Impex COMPETITOR CB-430 Manuale utente
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
CB-430
Retain This
Manual for
Reference
07-03-03
OWNER'S
MANUAL
COMPETITOR BENCH
CB-430
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................…. 1
IMPORTANT SAFETY NOTICES..................................................................…. 2
HARDWARE IDENTIFIER.....…....................................................................…. 3
ASSEMBLY INSTRUCTIONS........................................................................…. 4
EXPLODED DIAGRAM………………………………………………………………. 10
PARTS LIST...............................................................................................……. 11
WARRANTY.................................................................................................…. 12
ORDERING PARTS.......................................................................................… 12
BEFORE YOU BEGIN
Thank you for selecting the COMPETITOR CB-430 Bench by IMPEX
FITNESS PRODUCTS. For your safety and benefit, read this manual
carefully before using the machine. As a manufacturer, we are committed
to provide you complete customer satisfaction. If you have any questions, or
find there are missing or damaged parts, we guarantee you complete
satisfaction through direct assistance from our factory. To avoid
unnecessary delays, please call our TOLL-FREE customer service number.
Our Customer Service Agents will provide immediate assistance to you.
1
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT leave
children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine near water
or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or
other clothing that could become caught in the machine. Running or aerobic shoes are
also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or physician in
attendance.
10. Before using the machine to exercise, always do stretching exercises to properly warm
up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
HARDWARE IDENTIFIER
3
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches
NOTE: It is strongly recommended two or more people assembling this machine to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) Attach the Front Stabilizer (#22) to the Main Frame (#4). Secure it with two M10 x 3
1/8” Carriage Bolts (#54), one 4 ¾” x 1 5/8” Bracket (#26), two ∅¾” Washers (#64),
and two M10 Aircraft Nuts (#63).
B.) Connect the two Rear Stabilizers (#5) with the Lat Bar Base (#6). Attach the Main
Frame (#4) to the Lat Bar Base. Secure them together with two M10 x 3 3/8” Carriage
Bolts (#52), ∅¾” Washers (#64), and M10 Aircraft Nuts (#63). Diagram 1
4
STEP 2 (See Diagram 2)
A.) Slide the Sliding Weight Post (#11) onto the Lat Bar Frame (#1). Insert the Lat Bar
Frame into the opening on the Lat Bar Base (#6).
B.) Attach the Cross Brace (#7) to the Lat Bar Base. Align the holes on the Lat Bar Frame,
Lat Bar Base, and Cross Brace. Secure them with three M10 x 2 ¾” Carriage Bolts
(#56), one 1 5/8” x 2” Bracket (#38), one 6 ¾” x 2” Bracket (#39), three ∅¾” Washers
(#64), and three M10 Aircraft Nuts (#63). Do not tighten the nuts and bolts yet.
C.)Place the Backrest Adjustment Bar (#10) onto the holders on the Cross Brace.
D.)Attach two Spring Clips (#34) onto the weight posts on the Sliding Weight Post (#11).
E.) Insert one M10 x 2 3/8” Allen Bolt (#67) through the hole on the Lat Bar Frame. Secure
it with two Ø ¾” Washers (#64) and one M10 Aircraft Nut (#63).
DIAGRAM 2
5
STEP 3 (See Diagram 3)
A.) Attach the bottom of Right Upright Beam (#3) to the Rear Stabilizer (#5). Attach the Right
Upright Beam to the Cross Brace (#7).
B.) Secure the Right Upright Beam to the Rear Stabilizer with two M10 x 3 1/8” Carriage Bolts
(#54), ∅¾” Washers (#64), and M10 Aircraft Nuts (#63).
C.) Secure the Right Upright Beam to the Cross Brace with two M10 x 2 ¾” Carriage Bolts
(#56), one 4 ¾” x 2” Bracket (#27), two ∅¾” Washers (#64), and two M10 Aircraft Nuts
(#63).
D.) Repeat Steps A, B, and C above to install the Left Upright Beam (#2).
E.) Insert the Left & Right Bar Holders (#23 & 24) into the selected holes on the Upright Beam.
DIAGRAM 3
6
STEP 4 (See Diagram 4)
A.) Attach the Cable (#17) to the opening on the top of the Lat Bar Frame (#1). Make sure the ball
stopper of the Cable is underneath the Frame.
B.) Attach a Pulley (#29) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#57), two Ø 5/8”
Pulley Bushings (#43), two ∅¾” Washers (#64), and one M10 Aircraft Nut (#63).
C.)Draw the Cable to the bracket on the top of Lat Bar Frame. Attach a Pulley to the bracket. Secure
it with one M10 x 2” Allen Bolt (#55), one L-shaped Pulley Bracket (#28), two ∅¾” Washers
(#64), and one M10 Aircraft Nut (#63).
D.)Pull the Cable down to the Sliding Weight Post (#11). Secure the Cable to the Post with one M10
x 1 3/8” Allen Bolt (#53), two ∅¾” Washers (#64), and one M10 Aircraft Nut (#63).
E.) Connect a Chain (#37) to the Lat Bar (#12) with a C-clip (#36). Connect the Chain to the Cable
with another C-clip.
7
STEP 5 (See Diagram 5)
A.) Attach the Seat Support (#15) to the bracket on the Main Frame. Secure it with one M10 x 2
½” Allen Bolt (#57), two ∅¾” Washers (#64), and one M10 Aircraft Nut (#63).
B.) Attach the holes on the Backrest Supports (#16) to the pivot on the Seat Support (#15).
Attach the Backrest Board (#19) to the Backrest Supports (#16). Secure it with four M6 x 1
3/8” Hex Bolts (#58) and ∅½” Washers (#66).
C.)Place the Seat (#18) onto the Seat Support (#15). Secure it with four M6 x 5/8” Hex Bolts
(#60) and ∅½” Washers (#66). Insert a L-shaped Pin (#40) into the hole on the Seat Support
to lock the Seat and Backrest Board in position. Remove the Pin when folding the Backrest
Board forward to allow access to the “Walk-in Squat”.
D.)Attach the Arm Curl Pad (#20) to the Arm Curl Stand (#9). Secure it with two M8 x 5/8” Hex
Bolts (#61) and ∅5/8” Washers (#65).
E.) Insert the Arm Curl Stand into the opening on the Main Frame. Secure it with a M10 Lock
Knob (#33). DIAGRAM 5
8
STEP 6 (See Diagram 6)
A.) Attach the Leg Developer (#8) to the Main Frame. Secure it with M10 x 3” Allen Bolt
(#59), two ∅¾” Washers (#64), and one M10 Aircraft Nut (#63).
B.) Insert one Foam Tube (#25) halfway through the hole on the Main Base Frame. Insert
two Foam Tubes halfway through the holes on the Leg Developer.
C.) Push six Foam Rolls (#31) onto the Foam Tubes from both ends.
D.) Attach the Curl Bar Handle Frame (#13) to the Leg Developer. Secure it with a L-
shaped Pin (#40). Remove the Pin and the Curl Bar when doing Leg Developer
exercises.
E.) Attach a Spring Clip (#34) to the weight post on the Leg Developer.
DIAGRAM 6
9
Indice
Altri manuali Impex Palestra domestica
Impex
Impex MARCY WM-367 Manuale utente
Impex
Impex POWERHOUSE WM-1501 Manuale utente
Impex
Impex MARCY MWM-1840 Manuale utente
Impex
Impex Marcy SB-1315 Manuale utente
Impex
Impex IRON GRIP STRENGTH TSA-88 Manuale utente
Impex
Impex Marcy Diamond MD-859 Manuale utente
Impex
Impex Iron Grip Strength IGS-6900 Manuale utente
Impex
Impex MD-4100 Manuale utente
Impex
Impex WM PRO Manuale utente
Impex
Impex EVERLAST EVE-360 Manuale utente
Impex
Impex SB 650W Manuale utente
Impex
Impex Iron Grip Strength IGS-663 Manuale utente
Impex
Impex MARCY MKM-81030 Manuale utente
Impex
Impex MARCY SM-5092 Manuale utente
Impex
Impex POWERHOUSE WM-1501 Manuale utente
Impex
Impex Iron Grip Sport IGS-05 Manuale utente
Impex
Impex MARCY SM-4231 Manuale utente
Impex
Impex OLYMPIAN Manuale utente
Impex
Impex SA GEAR SAG-71 Manuale utente
Impex
Impex MARCY MWB-544 Manuale utente
