IMR IX616 Manuale utente

Ver. 1.0A4

Environmental Equipment, Inc.

IMR IX616 Portable Multi-Gas Detector

User Manual

Read this manual carefully before using this device.

(727) 328-2818 / (800) RING-IMR • Fax: (727) 328-2826

www.imrusa.com • [email protected]

Environmental Equipment, Inc. IX616

IMR IX616 User Manual

3632 Central Ave. St. Petersburg, FL 33711 Phone: 727-328-2818 / 800-RING-IMR

www.imrusa.com Fax: 727-328-2826

[email protected]m

THE PRIDE OF THE COMPANY –MADE IN THE USA Page 2of 12

CONTENTS

Service guidelines..................................................................................................................................3

Safety Information.................................................................................................................................3

1. Brief introduction ...........................................................................................................................4

2. Main Features and Specification ....................................................................................................4

2.1. Main Features..........................................................................................................................4

2.2. Technical Specification...........................................................................................................4

3. Structure and Function....................................................................................................................4

3.1. Appearance..............................................................................................................................4

3.2. Display Information ................................................................................................................5

3.3. Button Function.......................................................................................................................5

4. Operation Instruction......................................................................................................................5

4.1. Power On.................................................................................................................................5

4.2. Power Off................................................................................................................................6

4.3. Alarm.......................................................................................................................................6

4.4. Device Status...........................................................................................................................7

4.5. Calibration...............................................................................................................................7

4.6. Bump Test ...............................................................................................................................8

5. Data Communication......................................................................................................................8

6. Charging .........................................................................................................................................8

7. Sensor’s Use and Replacement.......................................................................................................8

8. Trouble Shooting Guide .................................................................................................................9

9. Usage Notice...................................................................................................................................9

Sensor Table.....................................................................................................................................10

10. Warranty ...................................................................................................................................11

11. Contact Information..................................................................................................................12

Environmental Equipment, Inc. IX616

IMR IX616 User Manual

3632 Central Ave. St. Petersburg, FL 33711 Phone: 727-328-2818 / 800-RING-IMR

www.imrusa.com Fax: 727-328-2826

[email protected]m

THE PRIDE OF THE COMPANY –MADE IN THE USA Page 3of 12

SERVICE GUIDELINES

1. Thank you for purchasing this product. Before operation, please read this manual carefully to

help prevent any accidents or damage to the device due to miss use.

2. Do not modify, repair, or replace parts in the device without contacting IMR, we assume no

liability for any harm caused due to improperly modified equipment.

3. Any damage caused due to incorrect operation shall not be covered.

SAFETY INFORMATION

Before using the detector please carefully read the below safety information first and follow the

operation requirement:

1. Do not use if damaged or defective. Before use check physical damage or missing parts.

2. Each day before use it is recommended to perform a “bump test” to ensure the detector is

operation properly. See section 4.6

3. It is recommended that a “bump test” be performed periodically to ensure that the audible, visual

and vibration alarms are set to the correct level and are functioning properly.

4. Only use authorized accessories provided by IMR. Use of unauthorized accessories may result in

damage to the device.

5. Only use the charger provided with the instrument to charge the detector. Only charge in a safe

environment. Charging in a hazardous environment is not advisable.

6. Detectors using catalytic sensors or semi-conductor sensors cannot be exposed to gases with

concentrations over the detector’s range. Doing so will overload the detector and interfere with

its performance or even cause damage.

7. Detectors using catalytic sensors or semi-conductor sensors cannot be exposed to gas

environments that contain lead compounds, sulfur compounds, phosphorous compounds or

silicon. These environments will damage a catalytic sensor or semi-conductor sensor.

8. Detectors using catalytic sensors or semi-conductor sensors cannot be exposed to gas

environment which contain hydrogen sulfide, halogenated hydrocarbon or highly corrosive

environments. These environments will dampen the sensor’s response and decrease the sensor’s

sensitivity to gases. If the detector has to be used in the above environments. Then preform a

“bump test” after use.

9. Do not expose the detector to electric shock, strong electromagnetic fields or intense continuous

mechanical vibration.

10. Do not discard the battery in the standard trash. Please follow all local regulatory and

environment regulations pertaining to lithium battery disposal.

11. Disassembly, modification, or repair of the detector by the end user is prohibited.

12. Take precautions to prevent the detector from being dropped at high elevations and intense

vibration.

13. For any usage or trouble shooting not covered in this manual contact IMR.

Environmental Equipment, Inc. IX616

IMR IX616 User Manual

3632 Central Ave. St. Petersburg, FL 33711 Phone: 727-328-2818 / 800-RING-IMR

www.imrusa.com Fax: 727-328-2826

[email protected]m

THE PRIDE OF THE COMPANY –MADE IN THE USA Page 4of 12

1. BRIEF INTRODUCTION

The IX616 is a multi-gas detector with

continuous detection of these combustible

gases O2, CO and H2S gases in the air. It has

a functional and watertight design (IP 66)

incorporates an impact absorbing rubberized

housing to meet the toughest requirement of

harsh environments like underground tunnels,

mines etc.

2. MAIN FEATURES AND

SPECIFICATION

2.1.MAIN FEATURES

Intrinsically safe design

100000 records storage capacity including

peak value

Calibration point adjustable

Adjustable 2-level alarm levels; STEL and

TWA alarm

Audible, visual and vibration alarms

Self-protection design for combustible gas

sensor

Low battery voltage alert function

Data uploading (to PC)

Password management

Self-test when powered on

Self-diagnostic and auto-correction

function.

2.2.TECHNICAL SPECIFICATION

Detection method: Natural diffusion

Detecting gas: See the “Sensor Table” on

page 10

Response time:

oFlammable gas: T90＜30s

oO2, CO, H2S: T90＜30s

Accuracy: ±5% FS (LEL) / ±5ppm (toxic

gas)

Working condition:

oTemperature: -20℃～50℃

oHumidity: ＜95%RH (non-

condensating)

Power source: Lithium battery, DC3.7V

1800mAh

Charging time: ≤ 6 hours

Battery working time: ≥ 8 hours (no

alarming status)

Explosion proof: ExiaⅡCT3

Ingress protection: IP66

Dimension: L*W*H

120mm×68mm×30mm

Weight: About 220g

3. STRUCTURE AND FUNCTION

3.1.APPEARANCE

1. Alarm indication LED

2. Button

3. Sensor ports

4. Display

5. Buzzer

6. Calibration cover fastener hole

7. Hand strap

8. Alligator clip

9. Label

10. Charging/ Communication port

Environmental Equipment, Inc. IX616

IMR IX616 User Manual

3632 Central Ave. St. Petersburg, FL 33711 Phone: 727-328-2818 / 800-RING-IMR

www.imrusa.com Fax: 727-328-2826

[email protected]m

THE PRIDE OF THE COMPANY –MADE IN THE USA Page 5of 12

3.2.DISPLAY INFORMATION

①Battery charge

②Sound

③Vibration

④Alarm

⑤TWA alarm

⑥High alarm

⑦STEL alarm

⑧Low alarm

⑨Gas name

⑩Unit of measurement

⑪Gas concentration

3.3.BUTTON FUNCTION

Power on: Hold for 1 second and then

release

Power off: Hold for 3 seconds until the

screen is off

Enable backlight: Press it once

Mute and cancel vibration: During

alarming status, press once

Check device status: While powered on,

backlight on and detection mode is active.

Press once and the screen will show the

device status including max value, min.

value, STEL value, TWA value, current

time, serial number and version number.

Calibration: After the device has entered

detection mode hold the button for more

than 20 seconds. The screen will then turn

off and then back on. When the screen

shows calibration mode release the button.

Note: The initial alarming method is buzzer +

flasher + vibrator. If the user needs to set the

alarming method install the PC software and

modify the setting there.

4. OPERATION INSTRUCTION

4.1.POWER ON

When the device is powered off hold the

button for 1 second and then release it. The

buzzer will sound once and the device then

powers on. The screen will cycle the below.

1. Full digit display, background light self-

test.

2. Time display, buzzer self-test

3. Version display, vibration self-test

4. High alarm value display, red light self-

test

Environmental Equipment, Inc. IX616

IMR IX616 User Manual

3632 Central Ave. St. Petersburg, FL 33711 Phone: 727-328-2818 / 800-RING-IMR

www.imrusa.com Fax: 727-328-2826

[email protected]m

THE PRIDE OF THE COMPANY –MADE IN THE USA Page 6of 12

5. Low alarm value display, yellow light self-

test

6. STEL alarm display, green light self-test

7. TWA alarm display

8. Count down

After the start up self-test has completed the

device then enters into detection mode. The

screen will show the concentration value of

the target gases.

Note: The device is set to auto zero calibration

after power on. It is necessary to power on the

device in an environment with “clean air”.

Otherwise an unreliable “zero” will be

obtained. This can lead to serious injury or

death. We assume no responsibility for the

failure to follow these guidelines.

4.2.POWER OFF

While in detection mode hold the button for 3

seconds. Buzzer does a long beep 3 times and

short beep twice. Then the device is powered

off.

4.3.ALARM

When the gas concentration in the air reaches

or exceeds the preset alarm levels the alarms

will trigger audible, visual and vibrate signals.

If the user cannot quickly exit this

environment quickly the audible and vibrate

alarms can be suspended by pressing the

button.

If the target toxic gas concentration reaches or

exceeds the preset value, the device will also

give STEL and TWA alert signals.

The instrument also has sensor fault alerts and

low voltage alerts. The screen will show the

relative alert indication.

Note: Verify that the STEL alert, TWA alert,

sensor fault alert and low voltage alert are

enabled before using.

Environmental Equipment, Inc. IX616

IMR IX616 User Manual

3632 Central Ave. St. Petersburg, FL 33711 Phone: 727-328-2818 / 800-RING-IMR

www.imrusa.com Fax: 727-328-2826

[email protected]m

THE PRIDE OF THE COMPANY –MADE IN THE USA Page 7of 12

4.4.DEVICE STATUS

In detection mode press the button once and

the screen will show the device status

including max value, min. value, STEL value,

TWA value, current time, serial number and

version number.

4.5.CALIBRATION

1. Gas input

2. Calibration cover

3. Fastener

With the device is in detection mode hold the

button for more than 20 seconds. The screen

will then turn off and then back on. When the

screen shows calibration mode release the

button.

The below screen will be displayed:

1. Entering the calibration interface

2. Sensors warming up

3. Zero calibration

Ensure the instrument is in “fresh air”

4. Gas input

The screen will display calibration gas

concentrations. After applying the standard

gas, the detector will start to analyze.

5. Auto calibration

6. Calibration pass/fail

Environmental Equipment, Inc. IX616

IMR IX616 User Manual

3632 Central Ave. St. Petersburg, FL 33711 Phone: 727-328-2818 / 800-RING-IMR

www.imrusa.com Fax: 727-328-2826

[email protected]m

THE PRIDE OF THE COMPANY –MADE IN THE USA Page 8of 12

7. Calibration completion

If you are going to calibrate more than one

type gas repeat the process. Mixed gases can

also be used to calibrate all the gases together

and then complete calibration in one cycle.

4.6.BUMP TEST

In order to make sure the IX616 is working

correctly it is suggested to do a “bump test”

before every use.

Test method: With the device is powered on

expose it to the target gas or standard gas

environment with high a concentration that is

beyond the high alarm level. If the device

reacts correctly and the reading is accurate

then the detector may be used in the field.

If the reading is beyond the regular error

ranges recalibrate the device. See section 4.5.

If the device does not respond or display is

faulty (error) contact IMR.

5. DATA COMMUNICATION

The PC software can be used to configure the

detectors settings and download sample data

to a computer for analysis.

Use the provided USB/Charging cable to

connect the device to a PC. After the device is

connected run the PC software.

Warning: DO NOT connect the device with a

computer in the detection site. The connection

or disconnection of the cable may cause sparks

which may lead to fire or explosion.

6. CHARGING

When the device cannot be powered on

because of low battery then the device should

be charged with the provided charger. Connect

it to an AC100~240V power source. The

device will automatically power on and begin

charging. The screen will show the charging

icon. When the icon shows the battery is full

disconnect the device from AC power. The

device will then work normally again.

Warning:

1. When charging the device while powered

off. It cannot be powered on and used to

detect.

2. It is hazardous to charge the device on site.

Doing so may cause fire or explosion.

3. Charging the device while powered off is

the fastest and most efficient method.

Note: Charge the device once every 3 months

if the device is not in regular use.

Avoid charging the device in an environment

with a temperature below 0℃ as this might

damage the battery.

7. SENSOR’S USE AND REPLACEMENT

The device uses modular sensors. Keep in

mind the age of the sensor modules. When the

sensor module is 3-5 years old replace it with

new one.

In order to guarantee accuracy it is suggested

to re-calibrate the sensor modules at least once

every 6 months.

Please ask IMR about sensor replacement.

After installing the new sensor module into the

device calibrate the new sensor before

returning the device to the field.

Environmental Equipment, Inc. IX616

IMR IX616 User Manual

3632 Central Ave. St. Petersburg, FL 33711 Phone: 727-328-2818 / 800-RING-IMR

www.imrusa.com Fax: 727-328-2826

[email protected]m

THE PRIDE OF THE COMPANY –MADE IN THE USA Page 9of 12

8. TROUBLE SHOOTING GUIDE

Issue

Potential Cause

Solution

Unable to

power on

Low battery

Charge for

the

recommended

duration

Unresponsive

Contact IMR

Circuit fault

Contact IMR

response

to gas

Warming up

Wait for

completion

Circuit fault

Contact IMR

Testing

reading

incorrect

Sensor overdue

for replacement

Contact IMR

Calibration out

of date

Calibrate the

sensor

Incorrect

time

Battery depleted

Charge the

device and set

the time

Electromagnetic

interference

Reset the

time

Gas value

displayed

negative

value

Sensor drift

Make zero

calibration

Sensor

fault

displayed

on the

screen

Sensor fault

Contact IMR

9. USAGE NOTICE

Avoid intense dropping or shocking.

If using in high concentration gas

environments the device will not work

normally.

Strictly follow this manual while using the

device. Failure to do so will cause

incorrect detection result or damage the

device.

It is forbidden to use and store the device

in corrosive environments (high

concentrations of CL2) or harsh

environments (exceedingly high or low

temperature, high humidity,

electromagnetic field, intense sunlight etc.)

After prolonged use if the device is dusty

use a clean soft cloth to clean it. Otherwise

the surface may become scratched or

damaged.

In order assure detection accuracy the re-

calibration period is every 6 months and

cannot be more than 1 year.

Do not discard the battery in the standard

trash. Please follow all local regulatory

and environment regulations pertaining to

lithium battery disposal.

For any usage or trouble shooting not

covered in this manual contact IMR.

Disassembly, modification and repair of

the device should be carried out by

authorized personnel only.

It is dangerous to charge the device or

upload data to a PC in hazardous

environments.

Environmental Equipment, Inc. IX616

IMR IX616 User Manual

3632 Central Ave. St. Petersburg, FL 33711 Phone: 727-328-2818 / 800-RING-IMR

www.imrusa.com Fax: 727-328-2826

[email protected]m

THE PRIDE OF THE COMPANY –MADE IN THE USA Page 10 of 12

SENSOR TABLE

Gas

Detection

Range

Preset

Low Alarm

Preset

High Alarm

TWA

STEL

0-30%vol

19.5%vol

23.5%vol

／

H2S

0-100ppm

10ppml

15ppml

10ppml

15ppml

0-1000ppm

35ppml

200ppml

35ppml

200ppml

LEL

0-100%LEL

20%LEL

50%LEL

／

Indice

Altri manuali IMR Altro

IMR

IMR IX 176 Manuale utente

Manuali Altro popolari di altre marche

GO Industries

GO Industries 38017 Manuale utente

Cissell

Cissell 30LBCMAN2 Manuale utente

RIDGID

RIDGID K-60SP Manuale utente

Gage Bilt

Gage Bilt GB751SH-5 Manuale utente

OVE

OVE SIERRA 60 Manuale utente

ReelCraft

ReelCraft 7800 OLB21 Manuale utente

Body Armor 4x4

Body Armor 4x4 ECO-SERIES Manuale utente

ROBLIN

ROBLIN DROP Guida utente

EMG

EMG EMG-ACB BARREL Manuale di servizio

MiniSolar

MiniSolar MT-150 Manuale utente

Parkside

Parkside PSZ 250 B2 Manuale utente

ABB

ABB REM 610 Manuale del prodotto

Parkside

Parkside 55992 Manuale del proprietario

Skyjacker

Skyjacker F250 Manuale utente

IBM

IBM IBM SYSTEM Z Guida all'installazione

Grech Motors

Grech Motors G28 Manuale utente

NOVAK

NOVAK BATTERY CARE SHEET Guida

Telemotive

Telemotive blue PiraT Mini Guida utente