Please read the product user manual carefully before installing and using this product, and keep the manual in a separateplace for future reference.
Aboutthecontentsofthemanual
Safetyrules
1. Explosive hazard
- This product complies with applicable standard code EN/IEC 60079-14, EN/IEC 60079-17,etc.
Installation andmaintenancemust be performedby qualifiedpersonnel accordingto national
standards.
- Do not openthe product while power is supplied within an explosion-proofarea.
- Installation of the product should be carried out using appropriatetools.
- The manufacturer recommends using explosion-proof tools.
- Connection testing and maintenance work in non-hazardous areas is recommended.
- Groundingis essential to reduce therisk of ignition of products installedin explosive
environments.
- The device must be connectedto protective earth.
At this time, it is recommended to use an approvedmaterial for thegrounding cable.
- Before turning on the product in a potentiallyexplosive place, check that the connectionparts
such as cable glands are properly closed. Check it out.
- If the surface temperature of the device is raised by direct sunlight exposure, the device's surface
temperature rating is rated against direct sunlight.
It is judged only by ambient air temperaturewithout consideration.
- Ensure that all devices are certified for the application and the environment in which it is installed.
- Any changes not approved by the manufacturer are not guaranteed.
2. Risk of electric shock
- When installing or performing maintenancewith the breaker turned on, make sure that the
product is turnedoff.
- A power-off device must be included in the electrical installation and can be recognizedvery
quickly and turned OFF when necessary. Need to check.
- An earth leakage breakerwith a maximum of 16Ais recommendedfor the electrical installation
to which the device is connected.
-The minimum gap between circuit breaker contacts must be 3 mm (0.1”).
- Do not useworn or corroded cables.
- All cablesmust comply with IEC 60332-1-2,IEC 60332-1-3 andIEC/EN 60079-14.
- When installing and operating, the characteristics of the power supply provided by the facility
and the characteristics of the power supply required by the product match Check if you do
- This product is not suitable for use in locations where children may be present.
3. Work attention
- Confirm that the installation methodmeets the explosion-proof regulationsand specifications.
After connection,it is recommendedto install aftertestingin a non-hazardousarea before
installation in the field.
- Use an appropriate cable that can withstand the operating temperature.
- All unusedcables must be electrically insulated.
- This product can only be installed in standard locations.
- Proceed with the installation after confirming whether the power supply source of the product is
PoE or DC power and the appropriate power source.
- Unauthorized modification by the manufacturer, use of non-genuinespare parts, unauthorized
use. Damage caused by installation, maintenance and repair by unskilled personnel
We accept no responsibility for any damage to the instrument.
- For technical service, refer only to authorized technicians.
- This product should only be repaired by properly trained personnel or under the supervision
of the manufacturer's personnel.
- When repairing, use only the manufacturer'sgenuine parts.
4. Understanding the installation process
- Installers must comply with general accident prevention standards when handling the product.
- Before proceedingwith the installation, compare/checkwith the componentsin the user
manual to check whether they match.
- Equipment installation in explosion-proof areas must be performed by professional technicians.
- The manufacturer assumes all responsibility for damages caused by improper use of the
device mentioned in this user manual.
doesn't support We also reserve the right to changesome parts without comment.
- It is the responsibility of the user to select the surfaceon which the productis to be fixed, so
there are instructions for attaching the product to a specific surface
Fixtures are not provided. It is the installer's responsibility to select the appropriate fixture for
their particular application.
Use installation methods and materials capable of supporting at least four times the weight of
the product.
- For all product maintenance, we recommend that you receive repairs by sending the product to
the manufacturer.
