Inform DSP FLEXIPOWER SERIES Manuale utente

DSP FLEXIPOWER SERIES .

SINGLE PHASE IN –SINGLE PHASE OUT

5-10kVA

THREE PHASE IN –SINGLE PHASE OUT

10kVA

UNINTERRUPTIBLE POWER SYSTEMS

Important Notices!

Thank you for choosing Inform UPS Systems.

This manual contains important information about technical properties, installation, comissioning

of the UPS and contains safety information for users and loads. Learning and applying of the

subjects in this manual is necessary to use UPS safely and correctly.

Units that are labeled with a CE mark comply with the Standard: EN 62040-1 and EN 62040-2.

Read the manual completely before working on this equipment!

Keep this manual near UPS for easy consultation!

Reproduction, adaptation, or translation of this manual is prohibited without prior written

permission of Inform Company, except as allowed under the copyright laws.

The manufacturer reserves the rights to change the technical specifications and design

without notice.

INFORM reserves the rights to change the information in this document without notice.

iii

Description of the Symbols Used in the Manual

Description of the Abbreviations Used in the Guide

UPS: Uninterruptible Power Systems

EPO: Emergency Power Off

RS232: Serial Communication Protocol

SNMP: Simple Network Management Protocol

CVCF: Constant Voltage Constant Frequency

V: Voltage

A: Ampere

P: Power

For Input, Output and Manual Bypass Circuit Breaker;

“I” (ON): Closing the Circuit

“0” (OFF): Opening the Circuit

For Battery Circuit Breaker;

Active (ON/I): Closing the Circuit

Passive (OFF/0): Opening the Circuit

Manufacturer

INFORM ELEKTRONIK SAN. ve TIC. A.S.

Emek Mah. Ordu Cad. No: 51 34785 Sancaktepe/ISTANBUL

Phone : 0216 622 58 00

Fax : 0216 621 46 55

This symbol points out the instructions which are especially important.

This symbol points out the risk of electric shock if the following instruction is not obeyed.

This symbol points out the instructions, which may be resulted with the injury of the

operator or damage of the equipment if not obeyed.

All packing material must be recycled in compliance with the laws in force in the country

where the system is installed.

INDEX

1. WARRANTY.........................................................................................................................................1

1.1. Terms of Warranty ......................................................................................................................1

1.2. Out of Warranty Terms and Conditions......................................................................................1

2. SAFETY................................................................................................................................................2

2.1. Important Notice for UPS............................................................................................................2

2.2. Important Notice for Battery ......................................................................................................3

2.3. Description of the Symbols Used on the Labels Applied to the UPS ..........................................3

3. REQUIREMENT ...................................................................................................................................4

3.1. Transportation.............................................................................................................................4

3.2. Placement....................................................................................................................................4

3.3. Storage ........................................................................................................................................5

4. UNPACKING AND INSTALLATION OF UPS ..........................................................................................6

4.1. Unpacking....................................................................................................................................6

4.2. Installation Procedures ...............................................................................................................8

4.2.1. PE Connection.....................................................................................................................11

4.2.2. Input Connection ................................................................................................................12

4.2.3. Battery Connection.............................................................................................................12

4.2.4. Output Connection .............................................................................................................13

4.2.5. Communiation Interface Connection.................................................................................13

5. MODES OF OPERATION....................................................................................................................18

5.1. Online Mode (norl)....................................................................................................................19

5.2. Eco Mode (Eco) .........................................................................................................................20

5.3. Bypass Mode .............................................................................................................................20

5.4. Battery Mode ............................................................................................................................21

5.5. Frequency Converter Operation (cF50 –cF60).........................................................................23

5.7. Manual Bypass Mode................................................................................................................23

6. FRONT PANEL & REAR PANEL ..........................................................................................................24

6.1. Front Panel Segments ...............................................................................................................24

6.1.1. Keypad ................................................................................................................................24

6.1.2. Liquid Crystal Display (LCD) ................................................................................................25

6.2. Rear Panel .................................................................................................................................29

7. OPERATING PROCEDURES ...............................................................................................................30

7.1. UPS Default Data and Special Function Execution....................................................................30

7.2. UPS Default Settings and Their Alternatives.............................................................................34

7.3. Commissioning ..........................................................................................................................35

7.3.1. Start-Up with the Mains .....................................................................................................35

7.3.2. Start-Up with the Battery (Cold Start)................................................................................38

7.4. Decommissioning ......................................................................................................................39

7.6. Manual (Maintenance) Bypass Instructions and Decommissioning.........................................40

7.7. Emergency Power Off (EPO)......................................................................................................41

8. MAINTENANCE.................................................................................................................................42

8.1. Batteries ....................................................................................................................................42

8.2. Fans ...........................................................................................................................................42

8.3. Capacitors..................................................................................................................................42

9. TROUBLESHOOTING.........................................................................................................................43

Appendix -1: Error List .........................................................................................................................45

Appendix -2: Technical Specifications..................................................................................................46

Appendix -3: Description of UPS and Block Diagram...........................................................................47

1. WARRANTY

1.1. Terms of Warranty

Warranty period begins from the date of commissioning of the UPS by Inform or authorized

Inform distributor technical personnel.

The UPS including all the internal parts is under the warranty of Inform.

If the UPS is malfunctioned because of component, manufacturing, or installation (if it’s done by

authorized personnel) problems during the warranty period, the UPS will be repaired without

asking any price for spare parts and labor cost.

Replacements, repairs or modifications of the parts during the warranty period can not extend the

duration of the warranty

1.2. Out of Warranty Terms and Conditions

This Warranty does not cover any defects or damages caused by;

If the UPS is not used or installed according to the terms in the manual, then the UPS is out of

warranty,

Neglect, accident, misuse, misapplication or incorrect installation,

Failure due to fortuitous circumstances or force majeure

After delivery of the UPS to the customer, unloading and transportation damage and failures,

Damage or injuries caused by negligence, lack of inspection or maintenance, or improper use of

the products,

Faulty electrical wiring,

Defects arising either from designs or parts imposed or supplied by the purchaser,

Defects and damage by fire and lightning,

Failures due to modification in the products without Inform approval,

Improper testing, operation, maintenance, repair, alteration, adjustment, or modification of any

kind by unauthorized personnel,

The Manufacturer will repair the device above cases for a fee and is not responsible for the

shipment of the equipment.

This Warranty is not valid if the Product’s Serial Number have been removed or is illegible.

2. SAFETY

2.1. Important Notice for UPS

The equipment may only be installed and commissioned by authorized technical personnel.

This manual contains important instructions that you should follow during installation and

maintenance of the UPS and batteries. Please read all instructions before operating the

equipment and save this manual for future reference.

For parallel system installation, please refer to parallel installation guide.

Because of “LITTLE LEAKAGE CURRENTS” generated by EMI Filter of the UPS, it is necessary to

double ensure if the earth of the UPS is properly grounded before AC mains is connected with.

Not obeying the instructions written on this manual which may be resulted with the injury of

the operator or damage of the equipment.

Even with no connections have been done, hazardous voltages and/or high temeperature may

exist on connection terminals and inside the UPS. Before beginning with the any installation or

maintenance, isolate the input and output of UPS and wait for 5 minutes for DC capacitor

discharge. If UPS has internal battery; remove the cover of UPS and disconnect the battery

cables.

The equipment shall be packed properly during transportation and proper equipment should be

used for transportation.

Make sure UPS is completely turned off when moving UPS from one place to another. It might

cause electrical shock if the output is not cut completely.

The UPS must always stands in a vertical position. Make sure that the floor can support the

weight of the system.

Connect the PE ground connector before connecting any other cable.

UPS is designed for indoor use. To reduce the risk of fire or electric shock, install this UPS in a

temperature and humidity controlled indoor environment, free of conductive contaminants.

Ambient temperature must not exceed 40°C (104°F). Do not operate near water or excessive

humidity (95% maximum).

Equipment and batteries whose packages are damaged during transportation shall be inspected

by qualified technical personnel before starting with the installation.

UPS requires Ph-N+PE input connection.

It should be checked between all the terminals included PE to be sure that no hazardous

voltages exist.

Do not connect the output neutral to the protective ground or protective bounding.

The connections shall be made with cables of appropriate cross-section in order to prevent the

risk of fire. All cables shall be of insulated type and shall not be laid out on the walking path of

the persons.

Contact your local recycling or hazardous waste center for information on proper disposal of the

used battery or UPS.

Make sure that the UPS is not overloaded to provide a higher quality supply to the loads.

In case of an extraordinary situation (damaged body or cabinet or connections, penetration of

foreign materials into the body or cabinet etc.) deenergize the UPS immediately and consult to

the Technical Service.

Information related to safety of the UPS, battery, load and the user is summarized below. But

the equipment should not be installed before reading the manual completely.

2.2. Important Notice for Battery

The batteries may only be installed and commissioned by authorized technical personnels.

Make sure that the battery qty is proper for the unit and they are same type and capacity.

Otherwise danger of explosion and fire is within the bounds of possibility.

Do not dispose of batteries in a fire. The batteries may explode.

Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes. It may

be toxic.

In case of electrolyte in contact with skin, immediately wash the contamimated skin with water.

Replaced batteries must be disposed of at authorized waste disposal centers.

A battery can present risk of electric shock and high short circuit currents.

The following precautions should be observed when working on batteries;

Remove rings, watches, neckleaces, bracelets and all metal objects.

Only use tools with insulated handles.

Wear rubbers gloves and a rubber apron when handling batteries.

Do not lay tools or metal parts on top of batteries.

Eye protection should be worn to prevent injury from accidental electrical arcs.

Before a maintenance or repair work on the UPS;

Switch the input and output circuit breakers (F1 and F2) to “0” position.

If UPS has internal batteries; Remove +battery (red) and - battery (black) cables.

If UPS has external batteries; switch the circuit breakers of the battery cabinet to

“0” position.

Determine if the battery is inadvertently grounded. If inadvertently grounded;

remove source of ground. Contact with any part of a grounded battery can result in

electrical shock.

2.3. Description of the Symbols Used on the Labels Applied to the UPS

PE: PROTECTIVE EARTH

PB: PROTECTIVE BOUNDING

DANGER! HIGH VOLTAGE (BLACK/YELLOW)

This symbol points out the instructions, which may be resulted with the injury of the

operator or damage of the equipment if not obeyed.

3. REQUIREMENT

3.1. Transportation

3.2. Placement

UPS is not designed for outdoor application.

The equipment and the batteries should not be exposed to direct sunlight or placed near to a

heat source.

Recommended operating temperature and humidity values are listed on the Appendix-2

Technical Specifications section. To provide the required enviromental condition.

Avoid dusty environments or areas where dust of conductive or corrosive materials is present.

The connection and the circuit breakers are at the back side of UPS. Leave at least 30 cm at the

back side of the UPS for maintenance.

Air outlets of the UPS are present on the front and back sides. Leave at least 30 cm at the front

and back side of the UPS for ventilation.

To eliminate any overheating of the UPS, keep all ventilation openings free from obstruction,

and do not store "things" on top of the UPS.

Even though the operating temperature of the UPS and batteries are between 0-40 °C, It is

suggested to provide an environment temperature between 20-25°C to get maximum

performance from the UPS and batteries.

Adviced Environmental humidity condition is between 30% 90% (non-condensing).

The UPS must be placed and stand in a vertical position throughout the transportation.

Use suitable equipment to remove the UPS from the pallet.

The equipment shall be packed properly during transportation. Therefore it is recommended

to keep the original package for feature need.

All packing material must be recycled in compliance with the laws in force in the country

where the system is installed.

3.3. Storage

Please store the UPS in an environment where the temperature is between –15 C +40 C, no

receipt of direct sunlight, far from the heating, in a dry place.

Environmental humidity must be between 30% 90% (non-condensing).

Recommended storage temperature, humidity and altitude values are listed on the Appendix-2

Technical Specifications section.

If the batteries will be stored for longer than 6 months, they shall be charged periodically. Charge

period depends on the storage temperature. The relationship is as shown below:

Every 9 months if the temperature is below 20°C,

Every 6 months if the temperature is between 20°C and 30°C,

Every 3 months if the temperature is between 30°C and 40°C,

Every 2 months if the temperature is over 40°C

For long storage duration; please follow up the instructions of installation described in Section 4,

start-up UPS described in Section 7 and charge the batteries at least 12 hours.

30%~90%

Relative Humidity

(non-condensing)

Indice

Altri manuali inform UPS

inform

inform SAVER PLUS DSP SERIES Manuale utente

inform

inform DSP Manuale utente

inform

inform 500 Manuale utente

inform

inform PYRAMID DSP PREMIUM Series Manuale utente

inform

inform PDSP31010 Manuale utente

inform

inform Pyramid Plus Scheda tecnica

inform

inform InfoSTS Manuale utente

inform

inform Guard 500VA Manuale utente

inform

inform Informer Compact Series Manuale utente

inform

inform Informer 1000VA Manuale utente

inform

inform GUARDIAN Manuale utente

inform

inform ETR EVO Series Manuale utente

inform

inform Pyramid DSP T Scheda tecnica

Manuali UPS popolari di altre marche

Pylontech

Pylontech Victron & Pylontech US5000 Manuale utente

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuale utente

Mecer

Mecer ME-1000-WTU Manuale utente

Mustek

Mustek PowerMust 530(B) Plus Manuale di installazione e funzionamento

Emerson

Emerson Liebert NXL series Manuale utente

MAKELSAN

MAKELSAN BOXER SERIES Manuale utente

Block

Block PC-0524-400-0 Manuale utente

CyberPower

CyberPower CP585LCD Manuale utente

Eaton

Eaton 3S Istruzioni per il montaggio

CyberPower

CyberPower Office Tower Series UPS 1000 Manuale utente

CyberPower

CyberPower BM100 Manuale utente

Best Power

Best Power 610 Manuale utente

Best Power

Best Power Unity/I UT3K Manuale utente

Mustek

Mustek PowerMust 400 Offline Manuale utente

Xantrex

Xantrex Trace 512 UR-UPS Manuale utente

Forza

Forza SL-1501UL Manuale utente

LEGRAND

LEGRAND keor 310081 Manuale utente

ABB

ABB Conceptpower DPA 500 Manuale utente

inform DSP FLEXIPOWER SERIES Manuale utente

Manuali UPS popolari di altre marche