Ingersoll-Rand P425AWIR Guida all'installazione
Book: 22600498 (1/05) 1
INSTALLATION, OPERATION AND SERVICE MANUAL
FOR
AUTO START STOP SYSTEM
OPTION FOR COMPRESSORS
P.O. Box 868
501 Sanford Ave
Mocksville, N.C. 27028
www.portablepower.irco.com
Doosan purchased Bobcat Company from Ingersoll-Rand Company in
2007. Any reference to Ingersoll-Rand Company or use of trademarks,
service marks, logos, or other proprietary identifying marks belonging
to Ingersoll-Rand Company in this manual is historical or nominative
in nature, and is not meant to suggest a current affiliation between
Ingersoll-Rand Company and Doosan Company or the products of
either.
Revised (09-12)
Book: 22600498 (1/05) 2
TABLE OF CONTENTS
SECTION 1 . . . . . . . Safety
SECTION 2 . . . . . . . Manual Description
SECTION 3 . . . . . . . General Information And Operational Theory
SECTION 4 . . . . . . . Installation
SECTION 5 . . . . . . . Troubleshooting Procedures
SECTION 6. . . . . . . Schematic Diagrams
SECTION 7 . . . . . . . Electrical/Electronic Component Locations
SECTION 8 . . . . . . . Electrical Connector Information
SECTION 9 . . . . . . . Electrical Parts List
SECTION 10 . . . . . . Alerts and Shutdown List
Book: 22600498 (1/05) 3
FOREWORD
This manual provides installation and operating instructions for field installation
of Auto Start capabilities for certain model air compressors.
Read these instructions before beginning the installation and check that all kit
parts are included. Assure all decals are attached.
Book: 22600498 (1/05) 4
SECTION 1
SAFETY
Follow all safety instructions in the air compressor operator’s manual and decals on the
machine and those included with the kit below.
WARNING
22306617
NOTICE
36573421
Book: 22600498 (1/05) 5
SECTION 2
MANUAL DESCRIPTION
This manual contains complete information for the electrical and electronic components for the Auto Start
Stop system. It provides installation, operation, troubleshooting and parts information for the system.
There are 10 sections.
Sections 2 – 4 cover systems operation, installation and troubleshooting procedures.
Sections 5 – 6 contain electrical schematics and component location information.
Section 7 contains electrical component locations.
Section 8 contains electrical connector information.
Section 9 contains the electrical parts list.
Section 10 contains the alerts and shutdowns list.
This Auto Start Stop option kit is for machine models:
P425AWIR XP375WIR HP375WIR
VHP300WIR P600WIR HP450WIR
VHP400WIR
IMPORTANT SAFETY INFORMATION
The auto start system can cause the machine to start at any time. Follow all
safety recommendations outlined in this manual to avoid injury to personnel.
DISCONNECT BATTERY BEFORE SERVICING.
WARNING
Book: 22600498 (1/05) 6
SECTION 3
GENERAL INFORMATION
And
OPERATIONAL THEORY
Book: 22600498 (1/05) 7
The following is a list of the items included in the Auto Start Kit. Make sure the kit contains all items
before beginning an installation.
Auto Start Module 22221063 Wiring Harness 22149157
Warning Lamp 22307698 Alarm Horn LS1 36785145
Terminal Strip TB1 22307706 Auto/Manual Switch S1 54615091
Switch Bracket 22311823 Battery Charger 54715941
Battery Charger harness 22600514 Battery Charger Bracket 22329411
Bag of fasteners “T” Harness 22600506
OPERATING INSTRUCTIONS decal 22313597
WARNING decal 22306617 (2 pieces)
NOTICE decal 36523421
Auto / Manual decal 22311815
AUTOSTART decal 36511244
Installation/Operation/Service Manual 22600498
Book: 22600498 (1/05) 8
GENERAL INFORMATION AND OPERATIONAL
THEORY
General
The auto start stop module provides a means of automatic start and stop capabilities for
compressors. It is designed to operate with any compressor that has the WEDGE
control system. It is a plug-and-play module that can be field installed.
The auto start module communicates with the WEDGE controller via the J1939 CAN
network on the machine. The auto start module commands the WEDGE controller to
perform machine start, load and stop functions based on external inputs to the auto start
module.
Machine CAN Network
The auto start stop module connects to the machine CAN communications network.
The CAN network is established by the WEDGE controller and the engine controller.
These are the two basic modules on the CAN network. The CAN network supports the
J1939 protocol as defined by the Society of Automotive Engineers (SAE).
The machine wiring harness contains two stubs for CAN / power access. These stubs
can be used for connection of any of the CAN network modules, including auto start
stop.
Figure 2-1 shows a schematic of the CAN network with compressor and engine
controllers and CAN stubs. One CAN stub is located behind the control panel of the
compressor and the other is near the lifting bail.
Sensors and Switches
Inputs
The Auto Start Module uses a pressure switch input to activate the automatic start-stop
function. This pressure switch is normally user provided and contains a single set of
normally open (N.O.) contacts. The N.O. contact closes to activate the auto start
feature and opens to disable the auto start feature. TB1 terminal strip (included in this
strip) has the input terminals for the pressure switch:
TB1-3 Start Switch
Book: 22600498 (1/05) 9
J1939CANCOMMUNICATIONSSCHEMATIC
P15
ENGINEDIAGNOSTICSJACK
J8
R5
R4
P7
P11
P6
ENGINE
CONTROLLERWEDGE
CONTROLLER
TERMINATORTERMINATOR
AUTOSTARTOPTION
CANNODEWITHPOWER
FIGURE3-1
Book: 22600498 (1/05) 10
An AUTO-MANUAL switch, S1, is provided to establish the mode of operation. It is an
input to the controller. When set in the AUTO position, the auto start stop feature will
function as described in this section. When placed in the MANUAL position, auto start
stop is disabled and the machine will function as it would normally.
Outputs
The auto start module provides four 24 VDC outputs for indicators. They are: low fuel,
compressor operating, crank alarm, and auto mode enabled. These outputs provide 24
VDC at 2 amps and can be used to drive indicator lamps or relays. They are typically
used to provide remote indication to a control room of the auto start compressor status.
The output to the alarm horn is provided through the wiring harness and is not brought
out to TB1.
The connections to the outputs are located on the terminal strip, TB1, provided with the
kit. They are as follows:
TB1-1 Auto start active output 24VDC
TB1- 5 Machine running output 24 VDC
TB1- 7 Low fuel indication 24 VDC
SECTION 5 of this manual provides schematic diagrams of the auto start system and
wiring harness connections.
Auto Start Stop Operation
Install the auto start kit as described in the Installation section. Make all electrical
connections before turning the machine power ON at the control panel. Once power is
turned ON, the WEDGE controller will automatically recognize the auto start module
and accept commands from it. To activate the auto start stop, place the AUTO-
MANUAL switch, S1, in the AUTO position. The DS1 lamp should illuminate.
The functional sequence is as follows:
1. When the external start switch (pressure switch) contact closes, the start
sequence begins. The contact closure must be maintained for 10 seconds
for the start sequence to initiate.
2. The auto start module instructs the machine controller to crank the engine.
The auto start module will sound the alarm horn 10 seconds before the
engine starter is engaged and during the cranking process. The machine
controller (WEDGE) will crank the engine until the engine starts or 20
seconds has elapsed.
Altri manuali per P425AWIR
2
Questo manuale è adatto per i seguenti modelli
6
Indice
Altri manuali Ingersoll-Rand compressore d'aria
Ingersoll-Rand
Ingersoll-Rand SSR UP6 15 Manuale utente
Ingersoll-Rand
Ingersoll-Rand DOOSAN P425WCU Manuale
Ingersoll-Rand
Ingersoll-Rand SS3F2-GM Manuale utente
Ingersoll-Rand
Ingersoll-Rand P110WIR Manuale utente
Ingersoll-Rand
Ingersoll-Rand XHP650CM Manuale di installazione e funzionamento
Ingersoll-Rand
Ingersoll-Rand Doosan XHP1070CMH-1800 Manuale utente
Ingersoll-Rand
Ingersoll-Rand GHH RAND SILU CS1050 LITE Manuale utente
Ingersoll-Rand
Ingersoll-Rand HP1300WCU-T3 Manuale
Ingersoll-Rand
Ingersoll-Rand P260WIR Manuale utente
Ingersoll-Rand
Ingersoll-Rand SS3 Manuale utente
Ingersoll-Rand
Ingersoll-Rand GHH RAND SILU CS700 LITE Manuale utente
Ingersoll-Rand
Ingersoll-Rand XF 7.5 Manuale utente
Ingersoll-Rand
Ingersoll-Rand SSR-2000 Manuale utente
Ingersoll-Rand
Ingersoll-Rand 9/215 Manuale utente
Ingersoll-Rand
Ingersoll-Rand R37-45 kW Manuale utente
Ingersoll-Rand
Ingersoll-Rand Thermo King V-520 Series Manuale utente
Ingersoll-Rand
Ingersoll-Rand GHH RAND SILU CS85 Manuale utente
Ingersoll-Rand
Ingersoll-Rand 2475 Manuale utente
Ingersoll-Rand
Ingersoll-Rand SS3L3 Manuale utente
Ingersoll-Rand
Ingersoll-Rand VHP600WCU Manuale utente
