Inguiti Max Speed Manuale utente

Max Speed –Personal 3D Stunt Micro Drone

www.ingeniousingenuity.com

Ages 14+ - Please read the instructions carefully before use.

www.ingeniousingenuity.com

Introduction

Thank you for choosing the Inguity® Max Speed Micro Drone from Ingenious Ingenuity Inc. This full featured

RC quadcopter is capable of advanced flight patterns for the experienced enthusiast, yet it can also be

operated by a beginner with ease. 6-Axis Gyro hovering, 360omovements at high and low speeds,

multidirectional maneuvering, headless mode for novice use, and incredible acrobatic techniques at your

fingertips for experienced pilots.

Safety Notes

The Inguity® Max Speed Micro Drone is not a toy. Improper use may result in serious injury to the operator,

bystanders, and/or property. Before operating, read all safety precautions and operating instructions. Failure

to follow precautions can result in bodily injury or damage to the unit. Avoid operating this drone around

populated areas or in proximity to power lines. Never operate during inclement weather such as strong wind,

rain, or snow. Do not leave children unattended while operating the drone.

Caution

The Inguity® Max Speed Micro Drone has parts that move at high speed. Keep hands and fingers clear of all

moving parts while in operation. Before handling the drone, power off remote to prevent sudden movement.

Fly in open space without obstacles, and do not operate near buildings, crowds of people, high voltage cables,

or other obstructions to ensure the safety of not only the operator, but other bystanders within proximity of

operation.

LiPo Battery Safety

The Inguity® Max Speed Micro Drone is powered with one 3.7 volt Lithium-Polymer (LiPo) battery. Never use

a battery that has been punctured or damaged. Never leave a charging battery unattended. When not in

use the LiPo battery is best stored at 50% charge. This will help maintain battery performance

And charge cycles. Do not dispose of the LiPo battery in a landfill. LiPo batteries require

proper disposal. Check with your local municipalities for proper disposal guidelines.

www.ingeniousingenuity.com

Inguity® Max Speed Micro Drone Parts

Included with your Inguity® Max Speed Micro Drone packaging are 8 propeller blades –4 installed on your

quadcopter and 4 replacement blades packed separately. 4 propeller guards are also installed on the

quadcopter and 1 pair of landing extensions are packed separately. A 4 Channel Remote Controller comes

packaged with your drone as well. For additional parts and information, please see our website at

www.ingeniousingenuity.com or contact us directly at 1-800-834-5279 for personal support during business

hours.

Inguity® Max Speed Micro Drone

The design and development of the Inguity® Max Speed Micro Drone ensures that when used properly, all

components are secured and fit for flight. Proper installation of the battery and any replacement propellers

will avoid damage to your unit. Please follow the steps below for a safe and easy way to install and uninstall

the battery and replacement propellers for a damage free process.

Installing Replacement Propellers

In the event that a propeller incurs damage and requires replacement, grip the propeller at the center of

rotation and pull upwards while holding the quadcopter at the motor housing. Do not apply force to the

blade guards or other fragile components of the quadcopter. In the event that the propeller will not easy

release, use a small flat head screw driver to wedge under the propeller and remove it from the motor shaft.

Once the damaged propeller has been uninstalled, select the matching propeller type. Note: There are 2

types of propellers (A and B blades). Be sure to install the correct blade style when replacing a damaged

propeller. Once the correct blade has been selected, press the blade onto the motor shaft at the center of

rotation until it appears secure.

IMPORTANT! PLEASE READ.

www.ingeniousingenuity.com

Inserting & Removing the Battery

You can only fit one 3.7V 1S Battery into the Inguity® Max Speed Micro Drone. The included battery comes

preinstalled in the drone. Note: We advise the user to not uninstall the battery from the drone body unless

it is being replaced. For charging and when the drone is not in use, please leave the battery in place to

avoid damage to the battery.

To remove the battery from the drone, locate the 2 wires coming from the corner of the battery. Gently pull

the battery from its compartment until you can grasp the body of the battery. Take extreme care to not

damage the battery when pulling the wires. We advise that the user only remove the battery if it is faulty

and damaging the battery is no longer a concern. To install a new battery, ensure that the wires from the

body of the drone are neatly pulled away from the entry way of the battery compartment. Gently the press

the battery into its compartment. If there is excessive resistance, reposition the battery to avoid damaging it

during installation rather than forcing it into its compartment. When properly installed, the battery should

press into its compartment with relative ease.

Before You Fly: Pair Remote with Quadcopter

The remote controller must first be assigned to your quadcopter before flight. When you power on your

remote controller, the indicator light will be flashing, which signals the user to pair the remote.

1) Now that you have followed the battery tutorial and have turned your Inguity® Max Speed Micro Drone

on, place your quadcopter on a safe, flat, and level surface for takeoff. Stand within 2 meters of your

quadcopter and turn on your remote using the power switch located in the center of the device. The

indicator light should now be flashing.

2) Push the throttle fully up and then fully down. The indicator light will now be solid and your controller will

beep once letting the user know that the frequency has been set and the remote is now connected.

3) Learn the flight commands and fly your quadcopter! Your remote should be fully functional

and paired with your drone.

www.ingeniousingenuity.com

Calibrating the 6-Axis Gyroscope & Accelerometer

1) Land drone or place on level surface for 3-5 seconds. The gyro will stabilize. If this does not solve your

unstable flight, try solution 2.

2) Turn your remote controller off –restart connection by turning it back on, push the throttle full up, then

full down until your remote beeps once and the indicator light is steady.

FCC Information

This equipment has been tested to comply with the limits for a Class B digital device, pursuant to Part 15 of

FCC rules. The limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not

installed and used in accordance with the instructions, may cause harmful interference to radio

communications. Although these tests have been performed to comply with Part 15, there is no guarantee

that interference will not occur in a particular installation. If interference occurs, you are encouraged to

correct the interference by any of the following methods:

- Connect equipment into outlet on a circuit different from the one the receiver is connected to.

- Increase distance between the equipment and the receiver.

- Relocate the receiving antenna.

- Consult your dealer or an experienced technician.

1) This device may cause harmful interference.

2) This device must accept any interference received, including that which may cause undesired operations

to occur.

www.ingeniousingenuity.com

Get to Know Your Transmitter

Controller Sensitivity

(High/Low)

Power Switch

(On/Off)

Altitude/Yaw Control

3D Flip Mode

Pitch Trim

(Forward/Reverse)

Pitch/Roll Control

(Click for Headless Mode)

Yaw Trim

(Left/Right)

Roll Trim

(Left/Right)

www.ingeniousingenuity.com

Troubleshooting

Transmitter and Inguity® Max Speed Do Not Pair

If you have more than one Inguity® Max Speed, ensure you are not pairing them at the same time. Although

up to 4 drones can be paired total, only one can be paired to the same remote at any given time. Pair one,

then turn on the second drone and pair that one. Continue this process until up to 4 devices are paired.

Turn the transmitter off. Push the throttle/accelerator stick (left stick) all the way down. Turn your controller

back on. The indicator light should be blinking. Push your throttle 100% up, then back down to 0%. A single

beep will occur and your unit should be paired. In some cases, removing the battery from the quadcopter

and repeating the steps are required.

Inguity® Max Speed Won’t Perform Flips

1) Battery power is too low to execute flips.

2) Controller did not properly pair with quadcopter.

3) 3D Eversion button was not pressed (continuous beeps until flip direction chosen).

Gyro is Not Working Well

1) Land or place the quadcopter on a level surface for 3-5 seconds without throttle (0% power).

2) Pair the drone with the transmitter again.

3) Land the drone with the throttle stick in full down position for 3 seconds and then take off again.

Quadcopter is Shaking and Making Noise

Check that the motors, canopy, body, and propellers are all properly positioned. If everything is intact and

properly fastened, re-stabilize your gyro by placing your quadcopter on a flat surface for 3-5 seconds.

Inguity® Max Speed Won’t Take Off

Have you recently changed your propellers? Check that they are in the correct positions.

When propellers rotate, the direction of air movement should be down.

www.ingeniousingenuity.com

Charging the LiPo Battery

3.7V 300mAh LiPo Battery

If you’ve just flown your quadcopter, give the battery some time to cool down. If your battery is now cooled

down, connect the battery adapter to the USB charger and plug the charger into a USB port. There is a red

light built into the charger that indicates that the battery is still charging. When the light has shut off your

battery charged. Note: Do not pull on the wires from the battery. Use only the plastic adapter clips and

use a tool if necessary. Pulling by the cord may result in damage requiring repair and is not covered by your

warranty.

Flying & Aerobatic Maneuvers –Flips, Rolls, 360 Degree Turns

High and Low Speed: On the top left of your controller is the controller sensitivity button. In high mode, your

speed, turns, and flight maneuverability is greatly enhanced.

3D Eversion: One the top right of your controller is the 3D Eversion button. When you click it, your controller

will continue to beep while awaiting the direction for the flip. This is given with the right stick.

Warranty: Your Inguity® Max Speed is covered by a 30 day limited warranty. Please visit our website for additional

details. www.ingeniousingenuity.com

Prevent Moisture: Moisture can damage your quadcopter or render it inoperable. You will also want to store your

battery and your quadcopter in a dry area at normal room temperature.

Rotating Blades Will Hurt! When in operation, the rotary blades of your copter mat be spinning at low or high

speeds. The blades are sharp and can inflict serious bodily injury or property damage. Keep your body and clothing

away from the propellers of your quadcopter. Do not take your eyes off the quadcopter or leave it unattended while

it’s turned on. If you lose control of your quadcopter, or it flies out of your view – turn it off immediately.

Avoid Flying Alone: Beginners should avoid flying a quadcopter alone while learning how to be the best

pilot they can be. We recommend flying with another more experienced flight pilot. If you do not

know another quadcopter pilot, watch some training videos on the internet.

www.ingeniousingenuity.com

Safety Check Before Flying

Inspect Your Quadcopter Before Every Flight.

- Check the battery and power plug are securely fastened. Severe vibration during flight may detach the plug

and result in loss of control.

- Turn the quadcopter on first, then your remote ensuring the power is at minimum before connecting

antenna by setting the throttle all the way up and then back down.

- If your propellers have loosened during a crash or become damaged –they could fly off during flight. A

crucial step before each flight is to ensure your propellers are still on properly.

- Before operation, check the batteries of the transmitter and that your Inguity® Max Speed battery is fully

charged for the flight.

- Carefully check rotor/propeller guards. If they have bent during a crash or in storage, your propellers may

hit them and break or break off during flight due to vibrations.

- Just like real aircraft, a useful safety solution is to have at least an idea of where you are going to go during

your flight. Plan a trip so you don’t lose sight of your craft and orientation. Have a plan in place if your battery

is dying during flight and lowering to the ground. Be prepared.

www.ingeniousingenuity.com

Lithium-Polymer (LiPo) Batteries

LiPo batteries are different from conventional batteries. As with all batteries, there is a risk of fire or

explosion if safety is ignored. Here’s a list of safety practices you can use to avoid fire, explosion or accidents.

- Keep the batteries away from children and animals.

- Do not overcharge batteries.

- Do not charge batteries near flames, flammable materials or liquids.

- Do not charge the batteries in a moving vehicle.

- Do not leave batteries unattended while charging.

- Have a fire extinguisher for electrical fires or a large bucket of sand nearby.

- NEVER try to extinguish battery fires with water.

- Store charging batteries inside of a suitable container.

- Change and store batteries in a location where a fire or explosion (including smoke) will not endanger life

or property.

- Do not charge the batteries if there is damage, have been punctured, or are ballooned/swelled.

- Ensure charging leads are properly connected and ensure proper polarity as reverse polarity charging can

lead to damage of the battery, fire, or explosions.

- If your battery is subjected to a shock (such as a crash or water), place it in a metal container. Observe for

swelling or heating for at least 30 minutes.

- NEVER take apart your battery. Do not dismantle, modify, or repair your battery.

It’s better to be safe than sorry. Battery accidents are an avoidable danger. Please user proper safety

methods while using Lithium-Polymer (LiPo) batteries.

LiPo Disposal & Recycling

Lithium Polymer (LiPo) batteries must not be placed in with household trash, Please contact your

environmental or waste agency or the supplier of your model for local re3gulations and the location of

your nearest LiPo battery recycling center.

Indice

Manuali Drone popolari di altre marche

Ryze

Ryze Tello Manuale utente

PowerVision

PowerVision PowerRay Manuale utente

Force1

Force1 rogue F72 Manuale utente

Zerotech

Zerotech DOBBY Manuale utente

Protocol

Protocol VIDEODRONE AP Manuale utente

dji

dji Matrice M210 Manuale utente

MAKE

MAKE Terry Kilby Manuale utente

SYMA

SYMA X440 Manuale utente

RUKO

RUKO F11 Manuale utente

SYMA

SYMA X5UW(720P) Manuale utente

Dynali

Dynali 25 H Guida

dji

dji PHANTOM 4 Manuale utente

Atlas

Atlas AtlasPRO Manuale utente

Twodots

Twodots TVVIN BOARD Manuale utente

GDU

GDU SAGA Manuale utente

Ares

Ares ETHOS QX 130 Manuale utente

Walkera

Walkera ZHUN Manuale utente

dji

dji WIND-4 Manuale utente