InHand InGateway974 Manuale di istruzioni

InGateway974 Quick Start Manual

This document contains the introduction, installation, and basic configuration of InGateway974 (IG974) such as

networking, software version update, etc., so that users can easily master the basic configuration of the IG974

and the use of common functions.

1. Introduction of IG974

1.1 Overview

1.2 Accessories List

1.3 Panel & Dimensions

•Panel

•Dimensions

1.4 Panel Indicators

•LED Indicators

•Signal Status Indicators

2. Installation

2.1 Install Notice

2.2 Rail Mounted and Dismounted

•Rail mounted equipment

•Rail dismounted equipment

2.3 Wall Mounted and Dismounted

•Wall mounted

•Wall dismounted

2.4 SIM Card Installation

2.5 Antenna Installation

2.6 Power Supply Installation

2.7 Protective Ground Installation

2.8 Network Cable Connection

2.9 Terminal Connection

3. IG974 Network Parameters Configuration

3.1 Access IG974

3.2 Connect to the Internet

4. Software Version Upgrade

4.1 IG974 firmware version upgrade

4.2 IG974 Python SDK version upgrade

4.3 IG974 Docker SDK version upgrade

5. Python Edge Computing

5.1 Install and operate Python App

5.2 Python App running configuration upgrade

5.3 Python App version upgrade

5.4 Enable Developer mode

6. Remote Monitoring Platform

7. Appendix

7.1 Restore Factory Settings

1. Introduction of IG974

1.1

Overview

The InGateway974 (IG974) series is the new generation industrial-grade 5G edge computing gateway

launched by InHand for the industrial IoT. The product provides high-speed, uninterrupted Internet

access base on 5G network and multiple broadband services. The IG974 supports a variety of

mainstream industrial protocols including Modbus TCP/RTU and can be connected to mainstream IIoT

cloud platforms including AWS and Azure, ensuring on-site devices can easily log into the cloud. With

strong edge computing capabilities, the IG974 provides an open edge computing platform to support

data optimization, real-time response, agile connection, and intelligent analysis at the edge nodes of the

IoT. Therefore, the IG974 significantly reduces the data traffic on-site and at the center, minimizes

operating expenses for users, and improves cloud performance.

The Common application scenarios of IG974：

1.2

Accessories List

Each IG974 product shipped from the factory includes common accessories for customer sites (e.g.

standard accessories list), after you receive our products, please check them carefully, and if you find

any missing or damaged, please contact INHANTONE sales staff in time.

In addition, we can provide customers with optional accessories according to different site characteristics,

please refer to the optional accessories list for details.

◼Standard Accessories

Item

Quality

Description

Gateway

InGateway974

Resources

QR code quick installation manual, user manual

Rail-mounted Installation

Accessory

Fixed gateway metal clips

Terminal

2-pin power terminal and 6-pin serial port

terminal

Network Cable

1.5m

Antenna

5G Antenna

Product Warranty Card

The warranty period is 1 year

Certificate of Conformity

Edge Computing Gateway Certificate of

Conformity

◼Optional Accessories

Item

Quality

Description

AC Power Cord

AC Power Cord-China Standard

Power adapter

12VDC Power adapter

Antenna

Wi-Fi Antenna

GNSS Antenna

Serial Cable

Gateway serial debug cable

1.3

Panel & Dimensions

1.3.1 Panel Introduction

IG974 panel introduction is shown below (IG974 series products have a variety of panel appearance

form, but the installation method is the same, the specific panel condition please subject to the physical).

1.3.2 Dimensions

The dimensions of IG974:

1.4

Panel Indicators

1.4.1 LED Indicators

IG974-Quick-Start-Manual-EN.md

2023/2/7

6 / 22

PWR

(Power Indicator-

Red)

SYS

(Status Indicator-

Green)

WARN

(Warning

Indicator-Yellow)

ERR

(Error Indicator-

Red)

NET

(Network

Indicator-Green)

Description

Light on

Light off

Start-up

Light on

Slow Blink

Light off

Start-up

successful

Light on

Slow Blink

Light off

Quick Blink

Dialing

Light on

Slow Blink

Light off

Light on

Dialing

successfully

Light on

Slow Blink

Light off

Reset

successfully

Light on

Slow Blink

Quick Blink

Light off

Upgrading

1.4.2 Signal Status Indicators

Signal: 1-9 (The signal condition is problematic, please check whether the antenna is well installed and

whether the signal condition in the area is good)

Signal: 10-19 (The signal status is normal and the device can maintain normal operation)

Signal: 20-31（The signal is very good）

2. Installation

2.1

Install Notice

⚫Power requirements: 24VDC (12 to 48VDC), please note the power supply voltage level; rated current

is 0.6A (1.2 to 0.3A).

⚫Environmental requirements: working temperature -25℃～75℃, storage temperature -40℃～85℃,

relative humidity 5%～95% (no condensation). The surface of the equipment may be high temperature,

IG974-Quick-Start-Manual-EN.md

2023/2/7

7 / 22

the installation needs to consider the surrounding environment and should be installed in a restricted

area.

⚫Avoid direct sunlight and stay away from heat generating sources or areas with strong electromagnetic

interference.

⚫Gateway products need to be mounted on industrial rails.

⚫Check the availability of cables and connectors required for installation.

2.2

Rail Mounted and Dismounted

2.2.1 Rail mounted equipment

The specific steps for installing the IG902 are as follows.

1. Select the installation position of the device, ensuring that there is sufficient space.

2. Snap the upper part of the DIN rail holder onto the DIN rail and rotate the device with slight force

at the lower end of the device upwards as shown by arrow 2 to snap the DIN rail holder onto the

DIN rail and confirm that the device is reliably mounted onto the DIN rail as shown in the right

figure below.

2.2.2 Rail dismounted equipment

To diamount the IG902, do the following:

1. Press down the device as shown by arrow 1 in the figure below, so that the lower end of the device

is free from the DIN rail.

2. Turn the device in the direction of arrow 2 and move the lower end of the device outward at the

same time, then lift the device upward after the lower end is free from the DIN rail to remove the

device from the DIN rail.

IG974-Quick-Start-Manual-EN.md

2023/2/7

8 / 22

2.3

Wall Mounted and Dismounted

2.3.1 Wall mounted

The specific steps for installing the IG902 are as follows.

1. Select the installation location of the device and make sure there is enough space.

2. Mount the wall mounting plate on the back of the device with a screwdriver, as shown in the figure

below：

3. Remove the screws (packaged with the wall mounting plate), fix the screws in the mounting position

with a screwdriver, and then pull down the device to make the device in a stable state, as shown in the

figure below.

2.3.2 Wall dismounted

To dismount the IG902, hold the device with one hand and remove the screw at the top end of the

device with the other hand to remove the device from the installation position.

2.4

SIM Card installation

IG974-Quick-Start-Manual-EN.md

2023/2/7

9 / 22

IG902 supports dual SIM cards, use a screwdriver to twist off the fixing screw on the card holder cover

and then install the SIM card, as shown below.

2.5

Antenna Installation

Gently turn the movable part of the metal SMAJ interface by hand until it can't be turned (at this time you

can't see the external thread of the antenna connection), don't hold the black rubber sleeve and screw

the antenna. As shown in the picture below.

Description:

IG902 supports dual antennas, which are ANT antenna and AUX antenna. The ANT antenna is the

antenna for sending and receiving data, while the AUX antenna can only enhance the signal strength of

the antenna, and cannot send and receive data independently, so it cannot be used alone.

IG974-Quick-Start-Manual-EN.md

2023/2/7

10 /

In general, only the ANT antenna can be used, when the signal is not good enough to enhance the signal,

only when using the ANT antenna at the same time use the AUX antenna.

2.6

Power Supply Installation

The specific steps for installing the IG902 power supply are as follows.

1. remove the terminal from the gateway.

2. loosen the locking screw on the terminal.

3. Insert the power cable into the terminal and lock the screw tightly.

2.7

Protective Ground Installation

The specific steps for installing the IG902 protective earth ground are as follows.

1. unscrew the grounding nut.

2. set the grounding ring of the cabinet ground into the grounding stud.

3. tighten the grounding nut.

Note: To improve the overall anti-interference ability of the gateway, the gateway must be grounded when

in use, according to the use of the environment will be grounded to the gateway grounding studs.

2.8

Network Cable Connection

Connect the gateway directly to the PC using a network cable as shown in the following figure.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali InHand Portale

InHand

InHand VT300 Series Manuale utente

InHand

InHand IG601 Manuale utente

InHand

InHand InGateway502 Manuale utente

InHand

InHand VT200 Series Manuale utente

InHand

InHand VG710 Manuale utente

InHand

InHand InGateway902 Manuale utente

InHand

InHand InGateway502 Manuale di istruzioni

InHand

InHand VG710 Manuale utente

InHand

InHand VG710 Manuale utente

InHand

InHand VG814 Manuale utente

InHand

InHand IG601 Manuale utente

InHand

InHand IG902-B Istruzioni operative e di manutenzione

InHand

InHand IG502 Istruzioni operative e di manutenzione

Manuali Portale popolari di altre marche

LST

LST M500RFE-AS Manuale utente

Kinnex

Kinnex Media Gateway Manuale utente

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuale utente

Telsey

Telsey CPVA 500 - SIP Manuale utente

RTA

RTA 460A-NNA4 Scheda tecnica

Shaw

Shaw Gateway HDPVR Manuale utente

ABB

ABB VSN900 Guida rapida

Commander

Commander Pulse Manuale utente

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuale utente

NETGEAR

NETGEAR C6300BD Manuale utente

Amit

Amit CDW531AM Manuale utente

HMS

HMS Netbiter EasyConnect EC150 Manuale utente

Huawei

Huawei EchoLife HG620 Manuale utente

AT&T

AT&T U-verse 3801 Manuale per l'uso e la cura

Logic IO

Logic IO RTCU MX2 turbo Manuale utente

Suttle

Suttle MediaMAX MXM-521 Manuale utente