INIM IC0020 Series Manuale utente

IC0020

Conventional resettable manual callpoint

ATTENTION!

IC0020 series manual call points are certified and approved according to EN54-11 -

Manual call points.

Description

IC0020 manual call points are specially designed to operate with

conventional control panels.

The device trigger element and red status LED are located in the

front case of the device. The LED will light up when the device is

activated.

The device details and information regarding the connection

terminals can be found on the label inside the device housing.

The device provides connectors for the resistance jumper. The

position of the jumper defines the alarm resistance, as follows:

The device package contains two fork-end keys which can be used

to open the housing and reset the device

The flush-mount backbox and the protective front plate are

accessory items and must be purchased separately.

Position Alarm resistance

RL 260 Ohm

RH 660 Ohm

Callpoint button - rear

Details label

Terminals

Backbox with fixing screw holes and cable entry

Fixed back-locking clips

Fixed back-locking clip positions

Back-locking backbox clips

Back-locking clip positions

Reset key slot

Protection front plate clips

Connectors for the resistance jumper

TECHNICAL SPECIFICATIONS

Operating voltage 10-30 Vdc

Resistance between terminals

“+” and “-” in the event of alarm 260 - 660 Ohm

Operating temperature -5°C / +40°C

Humidity

(without condensation) 95% RH

Dimensions (HxWxD) 84 x 84 x 45 mm

Weight 126 g

DCMIIN4AIC0020-R100-20120924

0832-CPD-2053

991j/01

IC0020

Activation

The IC0020 manual callpoint uses a simple mechanism which consists of a rigid plastic operating element and an

over-center spring mechanism. Pressing on the black spot simulates “Break Glass” activation and triggers an alarm.

Activation is signalled by a yellow and black striped flag which drops into view on the upper part of the frontplate

and by solid light on the red LED.

Reset

The IC0020 manual call point is reset by inserting the key provided into the key slot and by pushing the trigger

mechanism upwards as far as possible, after which the key must be turned clockwise until the mechanism locks

back into position.

ATTENTION!

The reset procedure must be carried out in accordance with the above instructions,

otherwise, you may damage the manual call point and/or its key.

Successful rest causes the flag to withdraw and the red LED to go off.

Installation

Connect the IC0020 manual call point to the control panel

using 2 wires.

The backbox has standard wall-mount anchor screw holes.

Insert the forked-end of the reset key into the two slots and

push against the back-locking clips to open the manual call

point.

Once all the devices are installed, refer to the control panel

manual for the instructions relating to the configuration and

end-of-line resistance.

Test and maintenance

Test the manual call point immediately after installation and

then regularly during the periodic tests which must be

carried out in accordance with the local laws in force.

Warnings and limitations

IC0020 manual call point is not suitable for outdoor

installation unless adequately housed inside a heavy duty

weather proof box.

INIM Electronics reserves the right to change

the technical specifications of this product

without prior notice.

INIM Electronics s.r.l.

via Fosso Antico, Centobuchi

63033, Monteprandone, (AP) Italy

Tel. +39 0735 70 50 07

Fax + 39 0735 70 49 12

www.inim.biz [email protected]

Indice

Altri manuali INIM Sistema di sicurezza

INIM

INIM NRB100 Istruzioni per il montaggio

INIM

INIM NRB100 Istruzioni per il montaggio

INIM

INIM Prime Manuale del proprietario

INIM

INIM PREVIDIA MICRO Manuale utente

INIM

INIM Sol-S Manuale utente

INIM

INIM enea EC0020 Series Manuale utente

INIM

INIM smartliving series Manuale utente

INIM

INIM snartliving Manuale utente

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente