INNO VIEW 3 Manuale utente
2017/05 Rev.1.2
User Manual
Please read this manual before
operating your fusion splicer,
and keep it for future reference.
1
View 3
User Manual
2
3
Contents
Introduction
Chapter 1: Technical specications
Applicable ber type
Splice loss
Splice mode
Heat oven
Power supply
Dimensions and weight
Environment
Other
Battery precautions
Chapter 2: Installation
Safety warnings and precautions
Operational safety warnings
Maintenance and external care precautions
Transport and storage precautions
Installation
Unpacking the splicer
Splicer overview
Power supply
Battery
Charge the battery
How to check remaining battery capacity
Battery refresh
Chapter 3: Basic Operation
Turning on the splicer
Adjusting the monitor position
Adjusting the monitor brightness
7
8
8
8
8
8
9
9
9
9
10
11
11
11
12
13
14
14
16
17
17
17
18
18
19
19
19
20
Contents 4
Touch screen On/Off
Fiber zoom function on screen
Preparing the bers
How to make a splice
Placing the bers
Inspecting the bers
Splicing
How to protect the splice
Heating procedure
Chapter 4: Splice Programs
Displaying the active splice program
Selecting a splice program
General splicing steps
Pre-fusion
Fusion
Splicing process
Splice program parameters under general splicing process
Chapter 5: Splice Option
Setting up splice mode
Chapter 6: Heater Mode
Selecting heater mode
Editing heater mode
Deleting heater mode
Heater mode parameters
Chapter 7: Maintenance Menu
Replace electrodes
Replacement procedure
Stabilize electrodes
Operation procedure
Diagnostic test
20
21
21
22
22
22
23
24
24
25
25
26
27
27
27
27
28
30
30
32
32
33
34
34
35
35
35
36
36
36
Contents 5
Operation procedure
Dust check
Operation procedure
Motor calibration
Operation procedure
Arc calibration
Operation procedure
Electrode setting
Update software
Chapter 8: Other Functions & Utilities
Data storage
Display splice record
Delete splice record
Cancel data storage
System setting
Monitor position
Power save option
System information
Appendix I: Reasons for high splice loss and solutions
Appendix II: List of error messages
Appendix III: Frequent questions and troubleshooting
36
37
37
37
38
38
38
39
39
40
40
40
40
40
41
42
43
43
44
46
49
6
Important: INNO Instrument strongly recommends all users to read this manual
before operating VIEW 3.
This manual is valid for the following software version:
7
Introduction
Thank you for choosing VIEW 3 Arc Fusion Splicer from INNO Instrument. View 3
adopts innovative product design and exquisite manufacturing technology so as to
deliver unprecedented splicing experience to customers.The totally new
technology greatly reduces splicing and heating time, and advanced estimation
method and alignment technique ensure the accuracy of splice loss estimation.
The simple-but-trendy product design, sophisticated internal structure and
reliable protective cover make the splicer be suitable for any operating
environment. Dynamic operation interface and automatic splice mode provide
users great convenience. For more information of VIEW 3, please visit our ofcial
website at www.innoinstrument.com
8
Technical Specications
Applicable ber type
•SM(ITU-T G.652&G.657) / MM(ITU-T G.651) / DS(ITU-T G.653)
/ NZDS(ITU-T G.655)
•Fiber count: Single
•Applicable ber cables: 0.25mm - 3.0mm / Indoor cable
•Applicable ber diameter: Cladding diameter: 80~150μm,
Coating diameter: 125~1000μm
Splice loss
Measured by cut-back method relevant to ITU-T standard:
•SM : 0.03dB
•MM : 0.02dB
•DS : 0.05dB
•NZDS : 0.05dB
•G.657 : 0.03dB
Splice mode
•Maximum 128 splice modes
•Internal splice data storage: 10,000
•Splicing time: SM Quick mode: 7s
Heat oven
•5 applicable protection sleeve: 20mm, 30mm, 40mm, 50mm, 60mm
•Heating time: 8- 900s
•Typical heating time: 30s
•Heat mode: Various heat modes available
•Heat oven: VIEW 3 special heat oven
1
Chapter 1 Technical Specications 9
Power supply
•Standard AC power voltage: AC 100-240V, 50-60Hz
•Standard DC power voltage: DC 9-14V
Dimensions and weight
•Size: Height x Width x Depth = 152mm x 147mm x 175mm
•Weight: 2.31kg (battery included)
Environment
•Operating condition: 0~5000m above sea level, 0~95% relative humidity,
-10~50℃, 15m/s max wind speed
•Storage condition: 0~95% relative humidity, -40~80℃
•Battery: -20~30℃for long time storage
Other
•Viewing and displaying method: two cameras and 5.0 inch color LCD monitor
•520x magnication for single X or Y view, or 520x magnication for
both X and Y view.
•Tensile test: 1.96-2.25N
•Terminals: USB2.0 / MINI USB
Indice
Altri manuali INNO Elettricità industriale
