Innovate 9500 Manuale utente
496332 Issue 1 1 of 22
9500
Installation and User Guide
Compatible Equipment
9525 Remote Keypad
9505 LIM
9507 LIM + PSU
9508 Shunt LIM (4 zones)
9509 Shunt LIM Controller
9510 EOL LIM (3 Zones)
9585 Engineers Printer (Centronics)
9589 Printer lead (Centronics)
9590 Hardware Mimic System
9597 Computer Mimic System
2 of 22 496332 Issue 1
Introduction
The 9500 Series System is a fully programmable, microprocessor controlled,
electronic intruder alarm system designed to meet the security requirements
of medium to large industrial and commercial premises.
The system operates on the “Multiplex” principle using four main data high-
ways (or branches) from the main control panel. Each branch comprises a
minimum 4-core cable, (6-core where keypads are included in branch), which
may be up to 2km (2000 metres) in length and may accommodate a combi-
nation of up to 16 Line Interface Modules (LIMs), Remote Keypads and
Isolation LIMs.
Figure 1. System Configuration
Each Line Interface Module has five double-pole circuits which can individu-
ally be programmed to any one of six circuit types and can feature any or all
9500
496332 Issue 1 3 of 22
of the seven circuit attributes, (Attributes do not apply to P.A., Technical
Alarm or 24 hour circuits).
The main control panel is provided with outputs suitable for connection to a
printer or a completely programmed mimic diagram system. The system will
accept a plug-in digital communicator (fast format only) or a direct-line
interface, which can also be used to connect the Series 9500 to “Red Care”
or “ABC” (Alarms by Carrier).
Technical Specification
Zones 0-320.
Display 32 Character “Supertwist” LCD.
Expansion By line interface modules of up to 5 circuits
per LIM.
BS 4737 Full Specification.
Log 450+ events ( Date andTime ).
Panel Siren No.
Internal Siren 9040 4 max.
Dimensions Panel h x w x d 290 x 400 x 10mm.
Dimensions Keypad h x w x d 180 x 110 x 40mm.
Weight Panel 4.6 Kg, Keypad 500g.
Battery 6 Ah.
Communicator
Output Plug-on STU/ 9058/9056 by using the 9578.
Signalling Conversion Interface.
Plug-on Interface 9576, 9576-01.
Outputs Bell relay contacts,
Strobe relay contacts.
Quiescent Current Ratings
12 Volt Power Quiescent: Panel 165mA, Keypad 50mA.
12 Volt AUX Output Not available unless detector power.
requirement less than 150 mA.
9500 Control Panel 165mA.
9558 Communicator 10mA.
9525 Remote Keypad 50mA.
9505 Standard LIM 10mA.
9506 Bare LIM 10mA.
9510 End Of Line LIM 10mA.
9508 Shunt LIM 10mA.
9509 Controller 12mA.
9500 Technical Specification
4 of 22 496332 Issue 1
Wiring
Figure 2. Main PCB Layout
Figure 3. Main PCB Connections
9500
496332 Issue 1 5 of 22
Figure 4. Standard LIM PCB
Figure 5. Connection of Shunt LIM as Single Shunt
9500 Wiring
6 of 22 496332 Issue 1
Figure 6. Connection of Shunt LIM as Multiple Shunt
Figure 7. Connection of End of Line Resistor LIM
Wiring 9500
496332 Issue 1 7 of 22
Figure 8. Remote PSU/LIM Layout and Connections
Figure 9. Remote Keypad Connections
9500 Wiring
8 of 22 496332 Issue 1
Figure 10. Wiring the Remote Keypad(s) to the Branch Loops
Figure 11. 9558 Communicator Layout and Connections
Wiring 9500
496332 Issue 1 9 of 22
Figure 12. 9576 Interface Layout
Figure 13. 9576-01 Interface Board Layout
9500 Wiring
10 of 22 496332 Issue 1
Programming
Initial Start Up
Check that all LIM box tampers are closed. Make sure that the Bell and
Strobe is not connected to the main 9500 PCB. Link out any circuits that are
nnot used.
When powering up the panel for the first time:
1. Close the control panel lid and connect the mains supply.
The display shows: <SYSTEM RESET>
12:00 16 OCT 90
Alternatingwith: 12:00 16 OCT 90
Status : Alarm
2. Key in 4567 + Enter.
The display shows: Display
customer log?
3. Press No.
The display shows: <SYSTEM RESET>
12:00 16 OCT 90
Alternatingwith: 16 OCT 12:00:00
CALL ENGINEER
4. Key in 7890 + Enter.
The display shows: Ver 4.20
14 FEB 1991
Followedby: Do you want
engineer reset?
Note: Whenever you enter engineer mode, the software version number and its date
will be displayed. Make a note of this number, as it will be useful when contact-
ing the Scantronic Product Support Department with any queries.
5. Press No.
The display shows: Do you want
test functions?
6. Press No.
The display shows: Do you want
reports?
7. Press No.
The display shows: Do you want to
program the system?
8. Open the control panel lid.
9500
Indice
Manuali Sistema di sicurezza popolari di altre marche
EDM
EDM Solution 6+6 Wireless-AE Manuale utente
Highway Safety Group
Highway Safety Group EA401 Manuale utente
Siren
Siren LED GSM Manuale utente
Detection Systems
Detection Systems 7090i Istruzioni per il montaggio
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuale utente
Siemens
Siemens FDM273 Manuale utente