Inscape Data NVS 460 Manuale utente

NVS460 User’s Guide

Rev1.0(Sep. 2006)

User

serser

ser’s Manual

s Manuals Manual

s Manual

1 Channel

1 Channel 1 Channel

1 Channel

Video Server

Video ServerVideo Server

Video Server / Encoder

/ Encoder / Encoder

/ Encoder

NVS 460

NVS 460NVS 460

NVS 460

NVS460 User’s Guide

Rev.1.0 (Sep. 2006)

2 of

of of

of 51

5151

Note

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules These limits are designed to provide

reasonable protection against harmful interference in a residential installation This

equipment generate, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications However, there is no guarantee that interference will not occur in a

particular installation If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures :

Reorient or relocate the receiving antenna

Increase the separation between the equipment and receiver

Connect the equipment into and outlet on a circuit different from that to which

the receiver is connected

Consult the dealer or an experienced radio/TV technician for help

Directions

NVS 460 are designed for indoor use only When using NVS 460 outdoors or in an

environment that exceeds the limited range, you must separately use a water-resistant case

Be careful not to cause any physical damage by dropping or throwing the NVS 460 Especially

keep the device out of reach from children

Do not disassemble NVS 460 You will be excluded from After Service when disassembled

Use only the power adapter provided with the NVS 460

If you would like to use the NVS 460 for security, monitoring, please check the legal

regulations within the country

NVS460 User’s Guide

Rev.1.0 (Sep. 2006)

3 of

of of

of 51

5151

This appliance and its antenna must not be co-located or operating in conjunction with any other

antenna or transmitter A minimum separation distance of 20 cm must be maintained between the

antenna and the person for this appliance to satisfy the RF exposure requirements

Caution

Any changes or modifications in construction of this device which are not explicitly

approved by the party responsible for compliance could void the user’s authority to operate

the equipment

NVS460 User’s Guide

Rev.1.0 (Sep. 2006)

4 of

of of

of 51

5151

1 Introduction...............................................................................................................................................5

1 1 Overview........................................................................................................................ 5

1 2 Features of NVS 460 .................................................................................................... 5

1 3 Applications of NVS 460............................................................................................... 6

2 Product Description ..................................................................................................................................7

2 1 Contents ........................................................................................................................ 7

2 2 Preview .......................................................................................................................... 7

2 3 Physical description ...................................................................................................... 8

2 4 PC Requirements ........................................................................................................ 10

2 5 Quick Installation Guide.............................................................................................. 11

3 Connecting NVS 460 to Network..........................................................................................................15

3 1 Connecting to LAN...................................................................................................... 15

3 2 Connecting to xDSL/Cable Modem ........................................................................... 16

4 IP-Installer...............................................................................................................................................18

4 1 Main window of IP-Installer....................................................................................... 18

5 Configuring NVS 460 in Administrative Mode.....................................................................................19

5 1 Log On ......................................................................................................................... 19

5 2 Basic Setup ................................................................................................................. 21

5 3 Network Configuration ............................................................................................... 23

5 4 Ommited.............................................................................. Error! Bookmark not defined.

5 5 User Admin & Time Setup ......................................................................................... 26

5 6 Sensor & Capture Setup ............................................................................................ 29

5 7 Alarm Device Setup.................................................................................................... 31

5 8 Motion Region Setup .................................................................................................. 33

5 9 PTZ Setup(only Pan/Tilt Device is can be used) ..................................................... 35

5 10 Encryption Set up..................................................................................................... 37

5 11 Upgrade & Reset....................................................................................................... 39

5 12 Status Report............................................................................................................ 41

6 Tips for using NVS 460 ..........................................................................................................................42

6 1 ALARM-IN and ALARM-OUT ....................................................................................... 42

6 2 Trouble Shooting......................................................................................................... 45

6 3 Web Viewer ................................................................................................................. 46

6 4 How to Upgrade the NVS 460 ................................................................................... 48

Table of Contents

NVS460 User’s Guide

Rev.1.0 (Sep. 2006)

5 of

of of

of 51

5151

1. Introduction

1.1. Overview

The NVS 460 is a state-of-the-art video server which transmits synchronized video and audio data

in real time with D1 resolution at full frame rate This is possible through MPEG4 CODEC technology,

which provides high quality video with highly compressed data streams The NVS 460 can be

connected, controlled and monitored from a remote location through an IP connection over internet

or intranet Unlike CCTV or DVR, the NVS 460 is easy to install and owner will experience cost and

space savings in the installation owing to the state of the art technologies embedded in the system

Based on Embedded Software Solution (Embedded Web Server, Embedded Streaming Server,

Network Protocol), the NVS 460 ensures unprecedented performance and stability to be an ideal

video server solution for system integration solutions

NVS 460 are offered with standard Ethernet interface while NVS 460 is offered with embedded WiFi

solution

1.2. Features of N S 460

 1 channel synchronized real time Video/Audio streaming

MPEG-4 video, ADPCM audio

 Bi-directional audio communication

Real time audio communication between NVS 460 and Client PC

 The viewer assisted recording and playback functions

 1 Alarm sensor input/1 relay output

 Motion detection – Up to 3 motion detection zones

Arbitrary shape motion detection zone

Motion detection can initiate video recording, which is sent to the user through FTP and/or E-mail

 Resolution

- NTSC : 704x480, 352x240, 176x144

- PAL/SECAM : 704x576, 352x288, 176x144

 RS-485 interface for Pan/Tilt device connection

 Remote administration control

Entire operational parameter set up, Software upgrade

 Proprietary PoE (Power over Ethernet) for convenience of installation and cost savings

NVS460 User’s Guide

Rev.1.0 (Sep. 2006)

6 of

of of

of 51

5151

1.3. Applications of N S 460

 Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government

facilities, military, etc )

 Real time Internet broadcasting

 Remote monitoring (hospitals, kindergartens, traffic, public areas, etc )

 Teleconference (Bi-directional audio conference)

 Remote Learning

 Weather and environmental observation

NVS460 User’s Guide

Rev.1.0 (Sep. 2006)

7 of

of of

of 51

5151

2. Product Description

2.1. Contents

Open the package and check if you have the followings:

Components Description Remarks

N S 460 NVS 460 Video server

Power adapter Input : 100~250V 50-60Hz

Output : +12V, 1 0A Standard Power

AC power cable AC 250V, 10A~16A

CD-ROM Software & User’s Guide

Quick Reference Guide

Quick installation guide Will be provided

2.2. Preview

N S 460 IP-Installer N R 100

1CH MPEG-4 Video

Server

PC software to allocate an IP

address to the NVS 460

PC software to view and record

the A/V streaming data

transmitted from NVS 460

NVS460 User’s Guide

Rev.1.0 (Sep. 2006)

8 of

of of

of 51

5151

2.3. Physical description

2.3.1. Front iew

Figure 2-1. Front view of N S 460

2.3.2. Rear iew

Figure 2-2. Rear & side view of N S 460 (left)

 MIC /LINE IN : Connect external audio source or microphone If external audio is connected,

embedded microphone will be disabled

Use Standard stereo earphone jack for the connection

NVS460 User’s Guide

Rev.1.0 (Sep. 2006)

9 of

of of

of 51

5151

Audio In

Ground

Not used

Audio In

Ground

Not used

Audio out

Ground

Not used

Audio out

Ground

Not used

Figure 2-3. Pin assignment of the plug for MIC/LINE In (left) and

LINE OUT (right)

 LINE OUT : Connect speakers with built in amplifier Audio from remote site is output through

Line out in bi-directional audio mode

Use Standard stereo earphone jack for the connection

 100BaseT : 100Mbps Ethernet connector (RJ-45) with proprietary PoE

- LINK LED : Continuous yellow light means that network cable is plugged in It will flicker

when there is traffic

- Status LED: Green color indicates that the camera is in normal operation mode, while RED

color indicates that the camera is in abnormal condition

 RS-232C & ideo-out

3 Pins from the bottom of the connector are assigned for RS-232 port, while the remaining 2

pins are used for checking composite video output Please note that the bottom most pin is

numbered as 1

Pin Description Misc.

1 TxD of RS-232C For debugging & factory use only

2 RxD of RS-232C For debugging & factory use only

3 Ground of RS-232C For debugging & factory use only

4 Video out from the camera For use in installation

5 Ground for Video out For use in installation

 DC7-23 , 8W: Power input of NVS 460

Do not apply power through this power input when power is applied through LAN cable using

proprietary PoE

NVS460 User’s Guide

Rev.1.0 (Sep. 2006)

1010

10 of

of of

of 51

5151





 RS-485 and ALARM IN/OUT : Used for connecting P/T device, sensor, and alarm devices to

NVS 460 Note that the bottom most pin is numbered as 1 Pin assignments are as follows

Pin Description Misc.

1 RS-485 Negative (-)

2 RS-485 Plus (+)

3 Alarm In (-) NC/NO selectable in admin mode

4 Alarm In (+) NC/NO selectable in admin mode

5 Alarm Out

6 Alarm Out

Relay output : closed circuit in alarm

to indicate alarm status

RS-485 : Used for connecting Pan/Tilt and Zoom devices having RS-485 interface

standard

Alarm In : Connect external alarm sensors such as the infrared sensors, heat

sensor, magnetic sensors, etc NC/NO selectable in the admin page

Alarm Out : It is used for connecting external alarm generators such as sirens,

flashing light, etc When activated, relay output configures a closed circuit





 Reset : Factory Default Switch

There is a switch provided for returning the video server to factory default state Press the

switch about 3 seconds through a tiny hole at the left of the 100BaseT connector using tools

with sharp tip for a few seconds while power is applied

2.4. PC Requirements

AV streaming data received from NVS 460 can be decoded or stored in a PC running NVR 100

program which is a viewing & recording program for a PC Minimum requirement of the PC is

described below:

Minimum Recommended

CPU Pentium III 700 Pentium IV 1 2G above

Main Memory 128 MB 256MB above

Operating system* Windows 2,000 or later Windows 2,000 or later

Web browser Internet Explorer 5 0 Internet Explorer 5 0 above

Indice

Manuali Convertitore multimediale popolari di altre marche

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuale utente

SPROLINK

SPROLINK VA1 Manuale utente

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuale utente

Nikon

Nikon AF-S TC-20E III Manuale utente

Axis

Axis AXIS Q7406 Manuale utente

Omega

Omega TAC80B-J Manuale utente

Zoom

Zoom Thunderbolt TAC-2R Manuale utente

OST

OST iConverter 10/100M Manuale utente

Vertiv

Vertiv Netsure Manuale utente

birddog

birddog MINI Manuale utente

Roland

Roland GI-10 Manuale utente

Wallenstein

Wallenstein WX310 Manuale utente

Pace

Pace MSS 200-1 Manuale utente

Solar Converters

Solar Converters EQ 12/24-50 Manuale utente

CYP

CYP EL-7400V Manuale utente

TIE

TIE MIDI 1i1o Manuale utente

DCS

DCS Vivaldi Upsampler Manuale utente

Westermo

Westermo MCW-211 SERIES Manuale utente