Inseego Wavemaker FW2010 Manuale utente
Inseego WavemakerTM
5G Outdoor Modem FW2010
Installation Guide
Preparing to Install
Tools and materials
• Installation handle (optional)
• Ladder
• Installation PoE* cable (RJ45 fittings attached)
• Smartphone/tablet for Inseego Mobile App
• 4FF nano SIM card (may come pre-installed)
• Phillips-head screwdriver
• M6 4mm hex driver
• Drill
• 14mm socket wrench/driver
• Needle nose pliers or tweezers
• Permanent round Cat6A PoE cable
• Ground wire
• Two RJ45 connector fittings for PoE cable
• Crimp tool to attach RJ45 fittings
• Cat6A Ethernet cable
• Sealing/weatherproofing material
Your 5G FW2010 comes in two packages:
• Device, PoE injector, and SIM tool
• Mounting bracket and hardware
*Power over Ethernet
About the FW2010
Description
The 5G Outdoor Modem FW2010 delivers
multi-gigabit data rates over 5G millimeter
wave networks using high power phased
array antenna modules. The FW2010 provides
extended range and coverage for millimeter
wave cellular networks and delivers data
connectivity to existing in-building networks.
Durability
The FW2010 has an environmental rating of
IP67 for water and dust ingress and can operate
within a temperature range of -30°C to 70°C
(-22 to 158°F).
Pre-Installation
1. If there is not a pre-installed SIM, unscrew
the protective shield over the SIM slots using
a Phillips-head screwdriver.
NOTE: This device supports only Nano SIM
cards.
2. Use the included SIM tool to insert a Nano
4FF SIM card into the SIM 1 slot.
CAUTION! Do not insert SIM card into the
SIM 2 slot - it will not work.
3. Reattach the protective shield cover to a
torque of 1.2 Nm (0.885 ft/lb).
4. For ease of carrying during the location
survey, attach the optional installation
handle to the back of the device with a hex
driver.
5. Unscrew the PoE gland cap and insert one
end of the installation PoE cable.
NOTE: This is for location survey purposes
only. You will install the permanent PoE
cable later. Set aside the bushing and cap.
6. Insert the other end of the cable into the
PoE injector PoE port. Plug the PoE injector
into an earthed AC outlet.
Location Survey
1. Scan the QR code to download the
latest Inseego Mobile App from App
Store or Google Play, or visit the link
below to download the App:
https://inseego.com/inseego-connect-
get-app
2. Follow instructions within the Inseego
Mobile App to connect to the FW2010 and
perform a 5G site survey to identify the ideal
location to install.
Rubber pin and
gland bushing Gland cap assembly
Installing the FW2010
Installing the PoE cable
1. Remove the installation PoE cable used for
the location survey from the device using
needle nose pliers or tweezers.
2. Remove the rubber pin from the PoE gland
bushing and assemble the gland cap,
putting the bushing inside the spacer and
into the cap.
3. Thread the permanent PoE cable through
the hole in the assembled PoE gland cap and
attach a RJ45 connector to the cable.
4. Insert the connector into the FW2010 and
screw on the gland cap. The cap will keep
the PoE connection secure and watertight.
M6 21mm bracket
mount bolt and washer
M5 10mm ground
screw / washer
4. Mount the device to the device elevation
bracket using a hex driver to tighten the bolts
to 2.0 Nm.
3. Place the M6 external locking washers on the
M6 21mm bracket mount bolts.
Attaching the device to the device elevation
bracket
1. Remove the installation handle from the
device.
2. Attach a ground wire to the back of the
device with the ground screw.
Roof mount lag screw
1. Pre-drill holes in the surveyed location.
2. Attach the mount using a hex driver to tighten
the lag screws.
NOTE: Concrete anchors are provided if
mounting to concrete or brick.
Installing the mount
The mount is adjustable and can be mounted on
vertical, horizontal, and slanted exterior surfaces.
The mount is attached using the four roof mount
lag screw in the corners of the base.
Securing the device elevation bracket to the
mount
1. Attach the device elevation
bracket to the mount and tighten
the square neck bolts along the
back to 2.0 Nm using a ratcheting
socket wrench.
2. Ground the ground wire to an
appropriate earth ground.
Orienting the device
1. Run the PoE cable to the desired location of the
PoE injector.
2. Attach a RJ45 connector fitting and insert
the cable into the PoE port on the PoE power
injector.
3. Take a racheting socket wrench and device/
smartphone with the Inseego Mobile App to
the FW2010 location.
4. Use the Inseego
Mobile App and the
positioning bolts on
the device elevation
bracket and bottom of
the mount to fine tune
the horizontal and
vertical angle of the
FW2010 for the best
signal.
5. Tighten the
positioning bolts to
15.0 Nm.
6. Use sealing/
weatherproofing
material to seal any
holes drilled in the structure to run the PoE
cable indoors.
LED Color Operation Meaning
Blue Solid
Blinking
Strong 5G connection (3 – 5 bars)
Weak 5G connection (1 – 2 bars)
Green Solid
Blinking
Strong 4G connection (3 – 5 bars)
Weak 4G connection (1 – 2 bars)
Yellow Solid Software update is in progress
Red Solid
Blinking
Router is booting up
No service, SIM error, or locked SIM card
Testing the connection
Checking the LED on the device
The LED is located in the SIM compartment and is
visible through the protective shield.
Connecting a device
You can connect any router or device with
Ethernet capability and an Internet browser to
the FW2010. Connect an Ethernet cable from
the DATA port on the PoE power injector to the
connecting device.
Connecting to the Web UI
1. On a connected device, open any browser and
enter: http://192.168.1.1.
2. Sign in using the default password: Fast5G!
IMPORTANT: For security purposes, please
ensure the user resets the Admin password in
the Web UI prior to finishing installation.
Multifunction LED
LED Color Operation Meaning
Blue Solid
Blinking
Strong 5G connection (3 – 5 bars)
Weak 5G connection (1 – 2 bars)
Green Solid
Blinking
Strong 4G connection (3 – 5 bars)
Weak 4G connection (1 – 2 bars)
Yellow Solid Software update is in progress
Red Solid
Blinking
Router is booting up
No service, SIM error, or locked SIM card
PN 90029656
© 2021 Inseego Corp. All Rights Reserved
Approved firmware versions
This device will only operate with firmware
versions that have been approved for use by your
wireless carrier and the device manufacturer. If
unauthorized firmware is placed on the device it
will not function.
Inseego Mobile App requirements
Smartphone or device on iOS 13 or above, or
Android 9.0 or above.
Support and more
More information
To access a User Guide, go to:
www.inseego.com/support-documentation/
Customer service and troubleshooting
Please contact your service provider.
Important information
System requirements
Any device with Ethernet capability and an
Internet browser. The 5G FW2010 is compatible
with the latest major operating systems and
versions of Web browsers.
Altri manuali per Wavemaker FW2010
2
Indice
Altri manuali Inseego Modem
Inseego
Inseego Wavemaker PRO 5G Outdoor CPE FW2000e Manuale utente
Inseego
Inseego Skyus DS Manuale utente
Inseego
Inseego Wavemaker FW2010 Manuale utente
Inseego
Inseego Wavemaker PRO Manuale utente
Inseego
Inseego USB8L Manuale utente
Inseego
Inseego Skyus SC Manuale utente
Inseego
Inseego AT&T Global Modem USB800 Manuale utente
Inseego
Inseego Wavemaker PRO 5G Outdoor CPE FW2000e Manuale utente
Inseego
Inseego Wavemaker PRO 5G Outdoor CPE FW2000e Manuale utente
Inseego
Inseego Skyus 3G Manuale utente
