Inspire ignite Manuale utente
WHAT'S IN THE BOX
TOOLS REQUIRED
www.inspirehomeautomation.co.uk
Ignite Sma Sensor
rev 1.1
2
1 x Ignite Sma
Sernsor
2 x AAA
Baeries
1 x Screw
Pack
Drill + 5mm
Drill Bit
Phillips
Screwdriver
INTRODUCTION
The Ignite Sma Sensor will detect temperature, motion and
humidity to help improve the efficiency of your heating. This
will link into an existing Ignite Heating System.
The Sma Sensor should not be installed in areas subject to
extended periods of high humidity, e.g. bathrooms
SPECIFICATIONS
Power Supply:
2 x AAA Alkaline Baeries
Temperature Range:
0-40°C
Humidity Range:
0-100% Rh
Motion Sensing Range:
70°@ 5 Metres - Horizontal
20° @ 5 Metres - Veical
Radio Frequency:
868 MHz
Dimensions:
68 x 68 x 23mm
3
RADIO SIGNAL
When choosing a location for your Sma Sensor, consider the
radio signal path. The signal will travel between units in a
straight line and will degrade both with distance and (much
more impoantly) objects that it has to pass through.
The Sma Sensor needs to connect to the Receiver (Ignite
Wireless / LITE) or Thermostat (Ignite Wired) via its internal
low power radio.
Every house is different, and this is NOT a guarantee, but as a
guide, the units should be able to communicate with each
other through two single skin brick or stud walls.
If the above is not possible, consider moving one or more of
the system components or ask us about our Ignite Signal
Booster.
Also, the radio can be adversely affected by large metal
objects such as your boiler, radiators, and mirrors. For best
peormance, ensure that your units are placed at least 1
metre away from such objects.
Fig 1 shows two possible Sensor locations, and the path that
the signal will travel to communicate between the Receiver
and Sensor. If the Sensor is located at "B", the signal will need
to go through two external walls.
If the Sensor is located at "A", it will have a significantly beer
signal as it will only have to travel through one internal wall.
4
Fig 2 shows another two possible positions. The Sensor located
at "B" will have the signal travelling entirely through a solid
wall. This will create a very poor signal, or no signal at all.
When moved to position "A" the signal will be considerably
stronger.
5
Fig 1
Fig 2
BATTERY INSTALLATION
We recommend that you pair the Sma Sensor with your
Ignite System prior to fixing it to the wall.
1. Whilst holding the back plate, rotate the outer cover
anticlockwise and remove in direction shown below
2. fit supplied baeries.
3. Secure outer cover by following Step 1 in reverse.
6
Fig 3
Fig 4
PAIRING INSTRUCTIONS
Put the Ignite device into pairing mode as detailed below
Ignite Wired
Press and hold 'CH MODE' and 'BOOST CH' keys
together on the Room Thermostat until C5 is
displayed.
Ignite Wireless / LITE (March 2021 onwards)
Long press BOTH buons on the Receiver until '1 and
WiFi' lights flash slowly.
Using the LEFT buon, cycle through the menu until
'CH' flashes.
Press the RIGHT buon, 'CH' will rapidly flash.
Ignite Wireless 4 channel / LITE 4 channel
(March 2021 onwards)
Long press BOTH buons on the Receiver until '1 and
WiFi' lights flash slowly.
Using the LEFT buon, cycle through the menu until
the required heating zone number flashes (1-4).
Press the RIGHT buon, this heating zone number will
now rapidly flash.
Ignite Wireless (March 2021 and earlier)
Sho press the pairing (middle) buon on the Relay
Module, this will make all three lights flash green.
Then press the CH buon, The CH buon will now
flash green.
7
TESTING THE SYSTEM
Ideally, the sma Sensor should be positioned at a height of
1.0 - 1.5 meters and in a high traffic area.
Hold the Sma Sensor in your desired location.
Press and hold /\ arrow buon for 5 seconds. The Ignite
Sma Sensor will enter into a signal strength mode.
A sweeping LED will be displayed whilst the signal detection in
in progress.
If a signal is detected, the strength will be measured from 1-5
lighting LEDs accordingly. to work effectively, the signal should
be a minimum of two LEDs.
If the unit has not been paired, two outside LEDs will rapidly
flash. Please return to pairing instructions on previous page
and follow the appropriate steps to pair the Sma Sensor
Sma Sensor
Ensuring the Inspire leaf logo is at the top, press and hold \/
buon for 5 seconds. All 5 LED's will slowly flash to indicate
unit is in pairing mode.
Upon successful pairing, the centre LED on the Sma Sensor
will rapidly flash.
If pairing fails, the two outside LED's will rapidly flash. Please
try the pairing procedure again.
8
INSTALLATION INSTRUCTION
4. Remove outer cover by repeating step 1
5. remove baeries, hold the device in the desired position and
mark screw mounting positions
6. Drill holes and fit supplied wall plugs (if required)
7. Mount device using supplied screws
8. Fit baeries
9. Secure outer cover by following Step 1 in reverse 9
Fig 5
Fig 6
USING THE SYSTEM
To Activate the Boost, press the /\ buon twice
To Cancel the Boost, press the \/ buon twice
Login to your account to view and configure your new Sma
Sensor.
If you are adding multiple Sma Sensors, you can RENAME
them via your online account. Please login and click the unit
setup to begin. We would recommend naming them as you pair
them to the Ignite system.
10
Fig 7
Altri manuali per ignite
4
Indice
Altri manuali Inspire Accessori
