Inspur NF5166M4 Manuale utente

No part of this document may be reproduced or transmitted in any form or by any

means without prior written consent of Inspur.

The information in this manual is subject to change without notice.

Inspur is the registered trademark of Inspur. All the other trademarks or registered

trademarks mentioned in this manual are the property of their respective holders.

Edition: 1

June 2016

Abstract

This manual contains technical information such as specications, hardware

operations, software conguration, fault diagnosis, etc. that are relevant to the

maintenance and operation of this server.

It is recommended that server installation, conguration, and maintenance to be

performed by experienced technicians only.

Target Audience

This manual mainly adapts to the following personnel:

●Technical support engineers

●Product maintenance engineers

It is suggested that server maintenance operation shall be carried out by professional

engineers with related server knowledge via referring to this manual.

Warnings:

TThis manual introduces the server’s technical features, system installation and

setup, which will help the user to understand how best to utilize the server and all its

functionalities.

1.For your safety, please do not disassemble the server’s components arbitrarily.

Please do not extend conguration or connect other peripheral devices arbitrarily. If

needed, please contact Inspur for our support and guidance.

2.Before disassembling the server’s components, please be sure to disconnect all

the power cords connected to the server.

3.BIOS and BMC setup is a signicant factor in correctly conguring your server. If

there are no special requirements, it is suggested to use the default values and not

alter the parameter settings arbitrarily.

4.Please use the driver shipped with the server or provided in Inspur ofcial website , if

you use non-Inspur driver, it may cause compatibility issues and affect the normal use of

the product, Inspur will not assume any responsibility or liability.

The manufacturer is not responsible for any damages, including loss of prots, loss of

information, interruption of business, personal injury, and/or any damage or consequential

damage without limitation, incurred before, during, or after the use of our products.

Table of Contents

1 Safety Instructions ........................................................................................... 1

2 Product Specications ..................................................................................... 6

2.1 Introduction ............................................................................................... 6

2.2 Features and Specications...................................................................... 6

2.3 Front Panel ............................................................................................... 7

2.4 Rear Panel ................................................................................................ 8

2.5 Motherboard Layout.................................................................................. 9

2.6 CLR_CMOS Jumper Introductions............................................................ 10

3 BIOS Setup...................................................................................................... 11

3.1 System BIOS Setup Methods ................................................................... 11

3.2 BIOS Settings ........................................................................................... 12

3.3 BIOS Update............................................................................................. 62

4 BMC Settings................................................................................................... 67

4.1 Introduction ............................................................................................... 67

4.2 Functional Modules................................................................................... 68

4.3 Web Interface Introduction........................................................................ 69

4.4 Command Line Introduction...................................................................... 97

4.5 Time Zone Table....................................................................................... 111

4.6 Key Features............................................................................................. 113

5 Hardware Maintenance.................................................................................... 115

5.1 Tool Preparation ....................................................................................... 115

5.2 Parts Replacement ................................................................................... 115

6 Common Faults, Diagnosis and Troubleshooting............................................ 126

6.1 Common Faults......................................................................................... 126

6.2 Diagnosis and Troubleshooting Instructions............................................. 127

7 Certications & Standards ............................................................................... 130

7.1 USA FCC Declaration ............................................................................... 130

7.2 CE Declaration of EU................................................................................ 130

7.3 China CCC................................................................................................ 131

7.4 China Environmental Labeling .................................................................. 131

Global Limited Warranty and Technical Support ................................................ 133

Hardware limited warranty .............................................................................. 133

How to obtain warranty service ...................................................................... 139

Types of warranty service ............................................................................... 140

Contacting Inspur............................................................................................ 141

Safety Introduction

1 Safety Introduction

Warning: the following warnings show that there are potential dangers that may

cause property loss, personal injury or death:

1. The power supply equipment in the system may generate high voltage and

dangerous electrical energy and thus cause personal injury. Please do not

dismount the cover of the host or to dismount and replace any component in

the system by yourself, unless otherwise informed by Inspur; only maintenance

technicians trained by Inspur have the right to disassemble the cover of the

host, dismount and replace the internal components.

2. Please connect the equipment to appropriate power supply, and the power

should be supplied by external power supply which is indicated on the rated

input label. To prevent your equipment from damages caused by momentary

spike or plunge of the voltage, please use relevant voltage stabilizing equipment

or uninterruptible power supply equipment.

3. If extended cables are needed, please use the three-core cables matched with

correct earthed plug, and check the ratings of the extended cables to make sure

that the sum of rated current of all products inserted into the extended cables do

not exceed 80% of the limits of the rated currents of the extended cables.

4. Please be sure to use the supplied power supply component, such as power

lines, power socket (if supplied with the equipment) etc. For the safety of

equipment and the user, do not replace randomly power cables or plugs.

5. To prevent electric shock dangers caused by leakage in the system, please

make sure that the power cables of the system and peripheral equipment are

correctly connected to the earthed power socket. Please connect the three-

core power line plug to the three-core AC power socket that is well earthed and

easy to access, be sure to use the earthing pin of power lines and do not use

the patch plug or the earthing pin unplugged with cables. In case of the earthing

conductors not installed and it is uncertain whether there are appropriate

earthing protections, please do not operate or use the equipment. Contact and

consult with the electrician.

6. To avoid short circuit of internal components and re or electric shock hazards,

please do not ll any object into the open pores of the system.

7. Please place the system far away from the cooling plate and at the place with

heat sources, and be sure not to block the air vents.

8. Be sure not to scatter food or liquid in the system or on other components, and

do not use the product in humid and dusty environment.

9. The replacement of batteries with those of another model may cause explosion.

When replacement of batteries is required, please consult rst the manufacturer

and choose batteries of the same or a similar model recommended by the

manufacturer. Do not dismount, extrude and pink the batteries or make

the external connection point short circuit, and do not expose them in the

environment over 60°C. Never throw them into re or water. Please do not

try to open or repair the batteries, and be sure to reasonably deal with the at

batteries and do not put the  at batteries, the circuit boards that may include

the batteries and other components with other wastes. For relevant battery

recovery, please contact the local waste recovery and treatment mechanism.

10. Before installing equipment in the chassis, please install front and side

supporting feet on the independent chassis; for cabinet connecting with

other chassis, it shall install the front supporting foot rst. If you fail to install

correspondingly the supporting foot before installing equipment in the chassis, it

may cause the cabinet to turn over in some cases, and thus may cause personal

injury. Therefore, it is necessary to install supporting feet before installing

equipment in the chassis. After installing the equipment and other components

in the chassis, it can only pull out one component from the cabinet through its

sliding component at one time. Pulling out several components at the same time

may lead the cabinet to turn over and cause serious personal injury.

11. Please do not move the chassis independently. Considering the height and

weight of the chassis, at least two people are needed to complete its movement.

12. Please do not carry out direct contact operation on power copper busbar when

the cabinet is powered on, and it is prohibited to carry out direct short circuit of

power copper busbar.

13. The product is Grade A product, and in the living environment, it may cause radio

interference. In such case, it may need the user to take feasible measures for the

Safety Introduction

interference.

Note: In order to help you use the equipment, the following considerations can help

avoid the occurrence of problems that may damage the components or cause data

loss etc.

1. In case of the following cases, please unplug the power line plug of products

from the power socket and contact customer service department of Inspur:

1) The power cables, extended cables or power plugs are damaged.

2) The products get wet by water.

3) The products have fallen off or been damaged.

4) Objects fall into the products.

5) When operating according to the operation instructions, the products cannot

function normally.

2. If the system becomes damp, please dispose according to the following steps:

1) Switch off the power supplies of the system and the equipment, disconnect

them with the power socket, wait for 10 to 20 minutes, and then open the

cover of the host.

2) Move the equipment to the ventilation place to dry the system at least for 24

hours and make sure that the system is fully dried.

3) Close the cover of the host, re-connect the system to the power socket, and

then start the equipment.

4) In case of operation failure or abnormal situation, please contact Inspur and

get technical support.

3. Pay attention to the position of the system cables and power cables, wire them

in places not to be stepped on or knocked down and ensure not to place other

objectives on the cables.

4. Before dismounting the cover of host or contacting the internal components, you

shall cool down the equipment rst; to avoid damaging the main-board, please

power off the system and wait for 5 seconds, and then dismount the components

from the main-board or disconnect the connection of peripheral equipment of

the system.

5. If there are modulator-demodulator, telecommunication or local area network

options in the equipment, please pay attention to the following matters:

1) In case of thunder and lightning weather, please do not connect or use the

modulator-demodulator. Otherwise, it may be subject to lightning strike.

2) Never connect or use modulator-demodulator in moist environment.

3) Never insert the modulator-demodulator or telephone cables to the socket of

network interface controller (NIC).

4) Before unpacking the product package, contacting or installing internal

components or contacting un-insulated cables or jacks of the modulator-

demodulator, please disconnect the modulator-demodulator cables.

6. In order to prevent the electrostatic discharge from damaging the electronic

components in the equipment, please pay attention to the following matters:

1) You shall conduct off the static electricity on the body before dismounting

or contacting any electronic component in the equipment. You can conduct

off the static electricity on the body by contacting the metal earthing objects

(such as the unpainted metal surface on the chassis) to prevent the static

electricity on the body from conducting itself to the sensitive components.

2) For electrostatic sensitive components not ready to be installed for

application, please do not take them out from the antistatic package

materials.

3) During the work, please touch the earthing conductor or the unpainted metal

surface on the cabinet regularly to conduct off the static electricity on the

body that may damage the internal components.

7. When dismounting the internal components with the approval of Inspur, please

pay attention to the following matters:

1) Switch off the system power supply and disconnect the cables, including

disconnecting any connection of the system. When disconnecting the

cables, please grab the connector of cables and plug it out, and never pull

the cables.

2) Before dismounting the cover of cabinet or touching the internal

components, the products need to be cooled down.

3) Before dismounting and touching any electronic component in the

equipment, you shall conduct off the static electricity on the body by

touching the metal earthingobjectives.

4) During the dismounting process, the operation shall not be too big, so as to

Safety Introduction

prevent damage to the components or scratching of the arms.

5) Carefully deal with the components and plug-in cards, and please never

touch, the components or connection points on the plug-in cards. When

taking the plug-in cards or components, you should grab the edges of the

plug-in cards or components or their metal xed supports.

8. During the process of cabinet installation and application, please pay attention

to the following matters:

1) After the installation of cabinet is nished, please ensure that the supporting

feet have been xed to the rack and supported to the ground, and all weight

of the rack have been fell onto the ground.

2) It shall install into the cabinet according to the sequences from the bottom to

the top, and rst install the heaviest component.

3) When pulling out the components from the cabinet, it shall apply force

slightly to ensure the cabinet to keep balance and stabilization.

4) When pressing down the release latch of the sliding rail of components and

sliding in or out, please be careful, as the sliding rail may hurt your gures.

5) Never make the AC power branch circuit in the cabinet overload. The sum

of cabinet load shall not exceed 80% of the ratings of branch circuits.

6) Ensure that components in the cabinet have good ventilation.

7) When repairing components in the cabinet, never step on any other

components.

2 Product Specications

2.1 Introduction

NF5166M4 is a 1U high-density storage server, supporting up to 2 Intel XEON E5-

26**V4 processors, 16 DDR4 DIMMs, 12 3.5-inch hot-plug SAS/SATA hard disks,

4 2.5-inch hot-plug SSDs, and 2 M.2 SSDs of 2280 specication; there are 2 1GbE

network ports on the motherboard; supporting OCP NIC slot; the system uses 700W

1+1 redundant power supply.

2.2 Features and Specications

Processor

Processor type Intel 2-socket XEON E5-2600V4 series (up to 2 135w processors)

Processor interface Socket-R3 (2)

Chipset

Chipset type PCH C612 (Wellsburg)

Memory

Memory type DDR4 ECC RDIMM/LRDIMM

Memory slot Qty. 16

Total memory capacity Support up to 512GB (32G per DIMM)

I/O interface

USB interface 2 rear USB 2.0 interfaces, 1 front USB 2.0 interface

Display interface 1 rear VGA interface

Serial Interface 1 rear serial interface

ID LED interface 1 ID LED (blue) and button

Display controller

Controller type Integrated in Aspeed2400 chip, support up to 1280*1024 resolution

SAS backplane

SAS backplane The internal SAS backplane supports hot-plug SAS/SATA HDDs.

The front SAS backplane supports hot-plug SSD HDDs.

Management chip

Management chip Integrate 1 independent 1000Mbps network interface, special for

IPMI remote management.

NIC

NIC controller

1 onboard Intel I350 dual-port Gigabit NIC, provide 2 1000M

adaptive RJ45 network interfaces; support 1 external network

daughter card.

Indice

Altri manuali Inspur Server di archiviazione di rete

Inspur

Inspur NF5280M5 Manuale utente

Inspur

Inspur AS500H Manuale utente

Manuali Server di archiviazione di rete popolari di altre marche

HP NetStorage 6000 Manuale utente

Seagate

Seagate U10 ST320423A Manuale utente

Synology

Synology RackStation RS816 Manuale

D-Link

D-Link ShareCenter Pro DNS-1200-05 Manuale utente

Avid Technology

Avid Technology VideoRAID ST Guida di sicurezza

Western Digital

Western Digital My Cloud Home Duo Manuale utente

PrimeArray

PrimeArray 4xxx Manuale utente

Buffalo

Buffalo TeraStation WSS WSH5010N6 Manuale utente

Planex

Planex MZK-NAS01SG Manuale utente

Intel

Intel SS4000-E - Entry Storage System NAS Server Manuale utente

Synology

Synology RS2212+ Manuale utente

Allnet

Allnet ALL69000 Manuale utente

Adaptec

Adaptec 5325301580 Manuale utente

Motorola

Motorola EXORdisk II Manuale utente

Sony

Sony XDAAI1PK Manuale utente

Cisco

Cisco Linksys NAS200 Istruzioni operative originali

Sans Digital

Sans Digital MR4UT6G Manuale utente

AIC

AIC FB128-LX Manuale utente