INSTROTECH IQ600 Manuale utente
Introduction
The load cell junction / summation box allows for easy connection / summation of up to 4 load cells to be connected in
parallel to the load cell instrumentation. Features of the junction / summation box include an IP65 protection ratin , ca e
clamp wire connectors for easy connection, a red LED for excitation indication and a clear lid for easy fault findin .
1 Features
Easy connection / summation of up to 4 load cells in parallel
IP65 Protection rating
Red LED indicating the presence of the load cell e citation voltage
Supports 4 or 6 wire load cells
Clear lid for easy fault finding
Shielded 6-wire connection to the load cell instrumentation
Cage clamp wire connectors
1 year limited warranty
Manual – English 1.03
IQ600
5-Way IP65 Load Cell Junction
Summation Bo
www.instrotech.com.au
2 Dimension & Template Drawing
3 Specifications
Enclosure:
Unit Dimensions 160x80x55mm (6.3x3.15x2.17”)
Enclosure Sealing Ton ue and roove with Neoprene seal
Enclosure Material Polycarbonate ( rey base, clear lid)
IP Protection Rating IP65
Connector Ratings: (Cage clamp wire connectors)
Conductor cross section solid min 0.2mm2
Conductor cross section solid ma 2.5mm2
Conductor cross section stranded min 0.2mm2
Conductor cross section stranded ma 1.5mm2
Conductor cross section solid min with
ferrule
0.25mm2
Conductor cross section solid ma with
ferrule
1.5mm2
Wire stripping length 7.5mm
Gland Ratings:
Clamping/sealing range 4-8mm (0.157-0.314”) Diameter wire
Environmental Conditions:
Operating temperature -10°C to 50°C (14°F to 122°F)
Storage temperature -40°C to 80°C (-40°F to 176°F)
Operating and storage humidity <85%, RH (non-condensin )
IQ600 Load cell Junction / Summation Bo Page 2
www.instrotech.com.au
4 Installation
Connect Load cells “LOAD CELL 1” to “LOAD CELL 4” notin the load cells correct wirin positions. Connect a suitable
shielded cable from the load cell instrumentation to the junction box connector marked “INSTRUMENT”. Make sure the
red LED is illuminated indicatin the presence of the excitation volta e when the load cell instrumentation is powered on.
If it does not illuminate then turn off the instrumentation and double check all connections.
Notes:
Ti hten the land nut until the rubber touches the cable completely and then ti hten the nut with ½ turn (180
de rees)
For unused lands either replace the lands with blank lands or insert a small off cut of wire to represent a
“Dummy load cell” to block the hole.
Install the junction / summation box with the lands pointin downwards with cable drip loops (If the cables and
junction box is exposed to water then bend a short downward loop in all cables near the cord rips so any water
drainin down the cables will drip off before reachin the junction box.
4-Wire Load Cells:
If usin 4-wire load cells then link the SEN+ to EXC+ and SEN- to EXC- on the specific load cell connector.
Note: Install with glands facing downwards and with cable drip loops
5 Ordering Information
IQ600 – 5 way Junction/summation box
IQ600 Load cell Junction / Summation Bo Page 3
www.instrotech.com.au
6 Notice
Specifications of the products displayed herein are subject to chan e without notice. Infiniteq cc, or anyone on its behalf,
assumes no responsibility or liability for any errors or inaccuracies.
Information contained herein is intended to provide a product description only. No license, express or implied, by estoppel
or otherwise, to any intellectual property ri hts is ranted by this document. Except as provided in Infiniteq's terms and
conditions of sale for such products, Infiniteq assumes no liability whatsoever, and disclaims any express or implied
warranty, relatin to sale and/or use of Infiniteq products includin liability or warranties relatin to fitness for a particular
purpose, merchantability, or infrin ement of any patent, copyri ht, or other intellectual property ri ht.
The products shown herein are not desi ned for use in medical, life-savin , or life-sustainin applications. Customers
usin or sellin these products for use in such applications do so at their own risk and a ree to fully indemnify Infiniteq for
any dama es resultin from such improper use or sale.
7 Warranty
This product carries a warranty for a period of one year from date of purchase a ainst faulty workmanship or defective
materials, provided there is no evidence that the unit has been mishandled or misused. Warranty is limited to the
replacement of faulty components and includes the cost of labor. Shippin costs are for the account of the purchaser.
Note: Product warranty excludes dama es caused by unprotected, unsuitable or incorrectly wired
electrical supplies and or sensors, and dama e caused by inductive loads.
DISTRIBUTED BY:
IQ600 Load cell Junction / Summation Bo Page 4
www.instrotech.com.au
Indice
Altri manuali INSTROTECH Protezione da sovratensioni
