Insys icom MRX DSL Manuale utente

ENGLISH

Quick Installation Guide

MRX DSL

www.insys-icom.com

These short operating instructions apply for the following devices of INSYS icom:

▪MRX3 DSL

▪MRX5 DSL

www.insys-icom.com/manual 

It is intended for a quick commissioning by the operator. Refer to the associated manual for further information.

This and other associated manuals can be found on our website in the menu Support > Documentation and

Downloads. Scan the QR code above or enter the URL into your web browser.

Technical Data

The product is only intendedfor the use within the permissible technical limits specified in the datasheets. These limits must be observed.

Operating voltage (redundant)

12 V … 24 V DC (±20%)

Supported DSL standards

VDSL2 G.993.2 Profile 8a, 8b,

8c, 8d, 12a, 12b, 17a. 30a

VDSL2 Vectoring G.993.5

Power consumption

approx. 6 W

fully equipped: max. 20 W

Supported DSL standards A

ADSL G.992.1 Annex A,

G.992.3. Annex A/L/M, G.992.5

Annex A and M, T1.413

Level input IN1

HIGH level = 2 ... 24 V

LOW level = 0 ... 1 V

Contact open condition: HIGH

Supported DSL standards B

ADSL G.992.1 Annex B,

G.992.3. Annex B, G.992.5

Annex B and J

Current consumption input IN1

at LOW potential

typ. 0.1 mA when connecting to

GND

Real-time clock (RTC) buffer

time

typ. 2 days

Level input IN2

HIGH level = 10 ... 24 V

LOW level = 0 ... 5 V

Contact open condition: LOW

Temperature range

0 °C … 50 °C

(-25 °C … 55 °C extended)

Current consumption input IN2

at HIGH potential

max. 3 mA at 24 V DC

Maximum permissible

humidity

95% non-condensing

IP rating

Housing IP40

AOnly for MRX3/5 DSL-A

BOnly for MRX3/5 DSL-B

Technical Boundaries

Max. line length for antennas, power supplies, serial interfaces, inputs and outputs as well as other signals: 30 m

Max. line length of USB connection lines: 3 m

Cable cross-section: 0.25 … 1.5 (2.5) mm² (depending on terminal size), flexible lines require end sleeves

A splitter must be connected upstream when connecting to DSL lines in telephone networks like Annex A or Annex B.

Support

If you need further support, please contact your sales partner or INSYS icom support. You can contact our support department via e-mail

under support@insys-icom.de.

Defects Liability Terms

A use other than the intended use, an ignorance of the safety instructions and the documentation, the use of insufficiently q ualified

personnel as well as unauthorised modifications exclude the liability of the manufacturer for damages resu lting from this. The liability of the

manufacturer ceases to exist.

In tended Use

The product may only be used for the purposes specified in the function overview of the manual. In addition, it may be used f or the

following purposes:

▪Usage and mounting in an industrial cabinet.

▪Switching and data transmission functions in machines according to the machinedirective 2006/42/EC.

▪Usage as data transmission device, e.g. for a PLC.

The product may n ot be used for the following purposes and used or operated under thefollowing conditions:

▪Use, control, switching and data transmission in machines or systems in explosive atmospheres.

▪Controlling, switching and data transmission of machines, which may involve risks to life and limb due to their functions or when a

breakdown occurs.

ENGLISH

Quick Installation Guide

MRX DSL

www.insys-icom.com

Router connection

1. Connect DSL connection line with VDSL/ADSL socket

2. Connect supply voltage (12 V … 24 V DC (±20%))

to the terminals V+1and GND

3. Connect router (ETH 1) to the configuration PC

4. Connect router (ETH 2) to the network

in which your system is located

LAN settings of configurations PC (Windows 7)

If a DHCP client is active on the PC, proceed with step C. Otherwise, either enable the

DHCP client or configure a static IP address.

5. Open Network and Sharing Center (e.g. key and search for "sharing")

6. Select LAN connection and Properties

7. Select Internet Protocol Version 4 (TCP/IP) and Properties

Enable DHCP client

8. Obtain an IP address automatically

It is recommended to unplug the

network cable briefly and plug it

again upon activation of the DHCP

client.

Configure a static IP address

Use the following IP address (example):

IP address: 192 . 168 . 1 . 2

Subnet mask: 255 . 255 . 255 . 0

Standard gateway 192 . 168 . 1 . 1

Preferred DNS server: 192 . 168 . 1 . 1

Please note the previous values before

changing the TCP/IP settings to be able

to restore them later.

Web interface access

9. Enter IP address of the router in address bar of the browser

(default: 192.168.1.1)

If a proxy server is enabled in your browser, this must be disabled or the IP address of

the router must be added as exception.

10. Login with

Name

(default: insys) and

Password

(icom)

11. Open the Inline Help using the button (Display help text) in the header

The links in the Inline Help lead to the Online Help with further information.

All modified data will only be stored in the opened profile after clicking the

Save

settings

button and become effective upon clicking the (Activate profile) button.

ENGLISH

Quick Installation Guide

MRX DSL

www.insys-icom.com

Configuration as DSL router

12. In Menu Help > Wizards: Select Startup Wizard

13. Select Internet access via DSL (refer to

inline help for WAN over Ethernet)

These data can be found in the contract

documents or can be requested from

the provider.

14. Select the access mode supported by

the provider and enter the appropriate

access data

15. Enter VLAN tag if required

16. Adjust VPI, VCI and Multiplex

according to the specifications of the

provider if required

17. Enter IP address of the local application

network

If the router is to be configured for the

icom Connectivity Suite - VPN

(https://connectivity.insys-icom.de),

select icom Connectivity Suite –VPN

under VPN connection and enter

Customer name and Device code (from

icom Connectivity Suite –VPN, “My

VPN Hub” tab). Then, the IP address in

the local network will be assigned by

the icom Connectivity Suite - VPN.

18. Click on

Execute wizard

The DSL LED flashes green during connection establishment; as soon as a connection

has been established (Showtime), it is illuminated green and blinks orange with data

transfer.

If the web interface of the router does not return upon executing the wizard, click on

“Reload” in the browser (or Ctrl+F5).

Configuration of access data

User name and password for web interface access of the existing user in the default

settings must be changed to prevent a manipulation of the configuration by

unauthorised persons.

19. Menu Administration > Users: Enter or change User name and Password and select

User group "Read/Write"

20. Store settings in profile with

Save setting

s and activate profile with

A typo during entering or forgetting the configured access data require a reset to

default settings to be able to access the router again.

All essential configuration steps are completed with this. Further configuration depends on your specific

application. Other frequently required settings are available on the following page.

ENGLISH

Quick Installation Guide

MRX DSL

Mat. no. 10019452 –version 18 December 2019 17:37:23 –Subject to technical changes and correction

www.insys-icom.com

IP address in configuration network

The IP address of the router in the configuration network does only have to be changed,

if the IP address is already used or a different address range is required. Then, the web

interface is immediately accessible under the new address.

1. Menu Interfaces > IP net 1: Adjust IP address of the router in configuration network

2. Store settings in profile with

Save settings

and activate profile with .

3. Adjust IP settings of the PC for further configuration accordingly, if these are not

obtained automatically (see step B)

4. Menu Services > DHCP Server: Adjust address range to the configuration network, if

the DHCP server of the router is used

Using the router as icom Smart Gateway

If the router is to be used as an icom Smart Energy or Machinery Gateway for example,

this is the best time now to install the icom Data Suite required for this. A wizard is

available for this in the

Help

menu. Refer to the Quick Installation Guide of the icom

Data Suite (https://www.insys-icom.com/manual#icom-data-suite) or the respective

Configuration Guide (https://docs.insys-icom.de/en_icom_data_suite.html).

Resetting the router

If it is necessary to reset the router during configuration, this is possible without losing

the settings.

1. Menu Administration > Reset:

2. Click on

Reboot device now

Alternatively, press reset key on the device front once for a short time (soft reset)

Resetting the router to default settings

If the router is to be reset to default settings, it can be reset to delivery state.

1. Menu Administration > Reset: check all options

2. Click on

Reset now

Alternatively, press reset key on the device front three times for a short time within

2 seconds

Resetting and initialising the router

If the router is not available any more for any reason, it can be reset and initialised

(settings do not get lost).

1. Press reset key on the device front for at least 3 seconds (hard reset)

The Inline Help opens upon selecting the button ? (Display help text) and provides helpful

information regarding each individual parameter directly in the web interface.

The Online Help is opened using the links in the Inline Help or in the Help menu in the web

interface and provides further information to the respective topics.

The Configuration Guides are available under https://docs.insys-icom.de and provide helpful

information regarding the integration of your product into your application.

Hereby, INSYS Microelectronics GmbH declares that herein described device types are in compliance with Directives 2014/30/EU

and 2011/65/EU. The full text of the EC Declaration of Conformity is available under www.insys-icom.com/manual.

Questo manuale è adatto per i seguenti modelli

Altri manuali insys icom Router di rete

insys icom

insys icom MRX LTE Manuale utente

insys icom

insys icom MRX3 LAN Manuale utente

insys icom

insys icom ECR-LW300 Manuale utente

insys icom

insys icom SCR Series Manuale utente

insys icom

insys icom EBW-W Manuale utente

insys icom

insys icom MoRoS LAN Manuale utente

insys icom

insys icom MRO-L200 Manuale utente

insys icom

insys icom SCR-E200 Manuale utente

insys icom

insys icom ECR-EW300 Manuale utente

insys icom

insys icom EBW-E Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza

insys icom MRX DSL Manuale utente

Manuali Router di rete popolari di altre marche