Intel Solid-State Drive Manuale utente

Intel®Solid-State Drive

Installation Guide 1

Intel®Solid-State Drive

Installation Guide

Overview

Installing an Intel SSD consists of three main steps:

Before you Begin

•Download and save the Intel Data Migration Software to your current storage device:

http://www.intel.com/go/ssdinstallation

•Confirm you have the necessary hardware for installation:

Note: Contents vary based on package purchased.

This guide explains how to install an Intel®Solid-State Drive

(Intel®SSD) in a SATA-based desktop or notebook computer.

The instructions include migrating your data from your current

storage device (such as a hard disk drive) to your new Intel SSD

using Intel®Data Migration Software.

1. Connect the Intel SSD to your computer.

2. Migrate your data from your current storage device to your new Intel SSD.

3. Swap the placement of your current storage device with your new Intel SSD.

Hardware item Required for

1. SATA-to-SATA interface cable Desktop computers

2. SATA power adapter Desktop computers without a SATA power cable

3. 3.5-inch mounting adapter and screws Desktop computers with 3.5-inch drive bay

4. USB-to-SATA cable Notebook computers

5. Drive sleeve Notebook computers (optional - for use with your old

storage device after the SSD is installed)

6. Phillips screwdriver Most computers

13 4 56

Intel®Solid-State Drive

2Installation Guide

Intel®Solid-State Drive

SSD Handling Precautions

Observe the following before beginning the installation:

•Keep the SSD in the protective anti-static container until you are ready to install.

•Handle the SSD with care. Do not touch the gold connectors.

•To minimize static electricity, touch the computer case before handling the SSD.

•Do not remove the encasement or disassemble the SSD; these actions void the SSD warranty.

This step explains how to connect the Intel SSD to your computer in preparation for migrating

your data. Note that your current storage device remains installed until the final step of the

installation, “Swap Your Drives” on page 8.

Follow the steps for your platform:

—“Desktop Computers” (next section)

—“Notebook Computers” on page 4

Desktop Computers

1.If your desktop computer has a 3.5-inch drive bay, attach the Intel SSD to the mounting

adapter. (This helps the SSD fit securely in a drive bay.) If your desktop computer has a 2.5-

inch drive bay, you do not need to attach the mounting adapter. Go to step 2 in this section.

a. With the SSD right side up (Intel logo showing), place the Intel SSD on the mounting

adapter. Make sure the edge of the Intel SSD (with connectors) aligns with the edge of the

mounting adapter. See Figure 1.

b. Turn the SSD and mounting adapter over and insert one screw in each mounting hole on the

bottom of the mounting adapter. See Figure 1.

Figure 1. Place and attach Intel SSD on mounting adapter

2.Power off the computer. Keep the power cable connected.

3.Remove the computer case.

Refer to your computer documentation to determine how to safely remove the computer case.

1. Connect the Intel SSD to your Computer

Intel®Solid-State Drive

Installation Guide 3

Intel®Solid-State Drive

4. Connect one end of the SATA-to-SATA interface cable to a SATA interface connector or

SATA host adapter on your computer motherboard and connect the other end to the

Intel SSD. See Figure 2.

Note: The SATA cable connectors are keyed to ensure correct orientation and contain a

locking bracket for securing in place. Insert cables gently. Do not use excessive force.

5. Locate an available SATA power cable (connected to the internal computer power supply) and

connect it to the Intel SSD. See Figure 2.

Note: Most computers have an available SATA power cable. If your computer does not have a

SATA power cable and instead uses a 4-pin power connector, use a SATA power adapter.

(The SATA power adapter comes with certain packages or can be purchased separately.)

Figure 2. Connect SATA interface and power cables

6. Slide the connected Intel SSD with mounting adapter into an available 3.5-inch drive bay, or

secure the Intel SSD to the computer by inserting one screw in each of the side-mounting or

bottom-mounting holes.

7. Power on the computer and wait for the operating system to recognize the Intel SSD.

A message appears when the SSD is recognized.

The Intel SSD is now connected. Proceed to “Migrate Your Data” on page 5.

1. SATA-to-SATA interface cable: Connect to SATA interface connector on computer motherboard and to Intel SSD.

2. SATA power cable (or SATA power adapter): Connect from power supply to Intel SSD.

Intel®Solid-State Drive

4Installation Guide

Intel®Solid-State Drive

Notebook Computers

1.Connect the dual end of a USB-to-SATA cable to two available USB ports on the computer.

See Figure 3. You do not have to power off the computer.

Note: If your computer contains a USB 3.0 port (indicated with a blue connector), connect

the blue end of the USB-to-SATA cable to the USB 3.0 port. If your computer does not

contain a USB 3.0 port, you can connect the cable to any USB port.

Figure 3. Connect USB-to-SATA cable to notebook

2.Connect the single end of the USB-to-SATA cable to the Intel SSD. See Figure 4.

Figure 4. Connect USB-to-SATA cable to Intel SSD

3.Power on the computer, if necessary, and wait for the operating system to recognize the

Intel SSD.

A message appears when the operating system recognizes the Intel SSD.

Note: SATA devices may draw more power than some systems are capable of delivering

through USB ports. If the Intel SSD is not recognized, remove other USB devices

(external keyboards, printers, mice, scanners, etc). Keep these devices removed until

you have finished migrating your data from the old storage device to the Intel SSD. In

some cases, it may be necessary to purchase an externally powered USB-SATA device

or have your system data migrated by a professional.

The Intel SSD is now connected. Proceed to “Migrate Your Data” on page 5.

Intel®Solid-State Drive

Installation Guide 5

Intel®Solid-State Drive

This section explains how to migrate (transfer) your data from your current storage device to

your new Intel SSD using Intel Data Migration Software.

Note: The migration process is identical for desktop and notebook computers.

1. Make sure you have downloaded and saved the Intel Data Migration Software to your current

storage device:

http://www.intel.com/go/ssdinstallation

Note: If the amount of data on your current storage device is greater than the capacity of

the Intel SSD, the data migration will not complete. Remove unnecessary files or data

from your current storage device to reduce its image size.

2. After downloading, double-click the Intel Data Migration Software icon to start the

installation.

3. When the Intel Data Migration Software installation screen appears, choose

Install Intel®Data Migration Software.

Figure 5. Intel Data Migration Software Installation screen

The Intel Data Migration Software wizard starts and guides you through the installation process.

4. Click Next to begin the installation.

5. Follow the prompts on the screen to complete the installation.

Note: When prompted for Setup Type, Typical is recommended.

6. Click Close when the installation completes.

7. Exit the Intel Data Migration Software screen, and proceed to the next section, “Start the

Software and Migrate your Data” on page 6.

2. Migrate Your Data

Intel®Solid-State Drive

6Installation Guide

Intel®Solid-State Drive

Start the Software and Migrate your Data

1.Double-click the Intel Data Migration Software shortcut icon on your desktop.

2.Complete the registration form when prompted, and then click Register Now.

After registering the software, the Intel Data Migration Software screen appears.

Figure 6. Intel Data Migration Software screen

3.Click Start Now.

Intel Data Migration Software automatically detects both drives, and the Clone Now screen

appears.

Figure 7. Clone Now screen

Intel®Solid-State Drive

Installation Guide 7

Intel®Solid-State Drive

Intel Data Migration Software works with Intel SSDs only. If you receive an error message,

make sure that you have an Intel SSD connected to your computer. If you have an Intel SSD

connected to your computer and still receive an error message, contact Intel support. See

“Additional Support” on page 10.

Intel Data Migration Software identifies your SSD and verifies that the used space on your

current storage device is the same or smaller than the available space on your SSD.

4. Click Clone Now.

The data migration starts. During this process, you will be prompted to reboot your computer.

Figure 8. Reboot screen

5. Click Reboot.

As your computer reboots, the migration process continues.

View the progress bar to see the status of the data migration. The length of the procedure

corresponds to the amount of data on the drive being transferred.

6. Once the operation completes, shut down your computer when prompted. Proceed to “Swap

Your Drives” on page 8.

Figure 9. Data Migration Successful screen

Intel Data Migration Software

Synchronizing with operating system:

[############################] 100%

Congratulations!

The cloning process completed successfully.

You can power off your system now and install

the cloned Intel SSD into your system.

Press any key to shut down the computer.

Intel®Solid-State Drive

8Installation Guide

Intel®Solid-State Drive

After you have migrated your data onto the Intel SSD and shut down your computer, swap the

placement of your current storage device with the new Intel SSD.

•For desktop computers:

— You can either physically remove the current storage device and replace it with the

Intel SSD (see “Desktop Computers — Physically Swapping the Drives”), or

— Keep the storage device in your computer and change the boot order of the drives in the

system BIOS to ensure that the computer boots from the Intel SSD (see “Desktop

Computers — Changing the Boot Order of the Drives” on page 9).

•For notebook computers, remove the current storage device and replace it with the Intel SSD

(see “Notebook Computers — Swapping the Drives” on page 9).

Desktop Computers — Physically Swapping the Drives

1.Make sure the computer is powered off.

2.Swap the SATA cable placement of the Intel SSD and your current storage device.

Figure 10. Swap drives

3.If desired, remove the current storage device.

Note: You may choose to keep your current storage device installed as a secondary or

backup drive. However, make sure to configure the system BIOS and change the boot

order so that the Intel SSD appears before your current storage device. See “Desktop

Computers — Changing the Boot Order of the Drives” on page 9.

3. Swap Your Drives

Intel®Solid-State Drive

Installation Guide 9

Intel®Solid-State Drive

4. After swapping the drives, power on the computer.

As your computer boots to the Intel SSD for the first time, a notification that the data

migration process completed successfully appears when the operating system starts.

Enjoy your new high-performing Intel Solid-State Drive!

Desktop Computers — Changing the Boot Order of the Drives

1. Close the computer case and start the computer.

2. While the computer is booting, enter the BIOS setup menu.

Press a special key such as ESC, F1, or DELETE to enter the BIOS menu. Check your

computer manufacturer’s documentation for the correct key(s).

3. Go to the Boot or Startup screen and change the boot order so that the Intel SSD appears

before your old storage device.

4. Save the settings and exit the BIOS setup menu.

5. Restart the computer.

As your computer boots to the Intel SSD for the first time, a notification that the data

migration process completed successfully appears when the operating system starts.

Enjoy your new high-performing Intel Solid-State Drive!

Notebook Computers — Swapping the Drives

1. Make sure the computer is powered off.

2. Remove the current storage device from the computer's drive bay.

Refer to your computer documentation for instructions on safely accessing the drive bay.

3. Remove any brackets or adaptors attached to the current storage device.

Not all storage devices have attached brackets or adaptors. If your devices does, remove

these and connect them in a similar manner to the Intel SSD.

4. Align the connector pins on the SSD with the SATA connector in the drive bay and slide the

SSD into the drive opening.

Figure 11.Install Intel SSD in notebook

Intel®Solid-State Drive

10 Installation Guide

Intel®Solid-State Drive

5.Replace the cover and power on the computer.

Note: You may choose to keep your old storage device as a secondary or backup drive by

connecting it to the computer using the USB-to-SATA cable. Protect the old storage

device with the drive sleeve included with certain packages. Install the drive sleeve

with caution. Intel is not responsible for data loss or damage to system components.

As your computer boots to the Intel SSD for the first time, a notification that the data

migration process completed successfully appears when the operating system starts.

Enjoy your new high-performing Intel Solid-State Drive!

Additional Support

For more help with Intel SSDs, go to: http://www.intel.com/support

For more information about Intel SSDs, go to: http://www.intel.com/go/ssd

For instructional videos and to learn more about Intel SSDs, go to:

http://www.intel.com/go/ssdfacebook

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Intel Magazzinaggio

Intel

Intel SSR212CC Manuale utente

Intel

Intel SS4000-E - Entry Storage System NAS Server Manuale utente

Intel

Intel SS4000-E - Entry Storage System NAS Server Guida alla configurazione

Intel

Intel SSR212MA Manuale utente

Intel

Intel JBOD2000S3SP Manuale utente

Intel

Intel SSR316MJ2 Manuale utente

Intel

Intel 910 Series Manuale utente

Intel

Intel JBOD2312S3SP Istruzioni per l'installazione

Intel

Intel SSR212MA Guida alla configurazione

Intel

Intel SSR212MA Manuale utente

Intel

Intel 760p series Manuale utente

Intel

Intel SSDPAMM0004G1 Manuale utente

Intel

Intel SS4200-EHW Guida

Intel

Intel SS4200-E - Entry Storage System NAS Server Guida alla configurazione

Intel

Intel Solid-State Drive 320 Series Manuale del proprietario

Intel

Intel SS4000-E - Entry Storage System NAS Server Guida all'installazione

Intel

Intel PowerEdge External Media System 1434 Manuale operativo

Intel

Intel SSR212PPi500 Guida

Intel

Intel SSR316MJ2 Guida

Intel

Intel JBOD 2000 Family Istruzioni per l'installazione

Intel

Intel SS4200-E - Entry Storage System NAS Server Manuale utente

Intel

Intel SSR212CC Guida alla configurazione

Intel

Intel X25-E Extreme Guida di riferimento

Intel

Intel SSDSA1MH080G1 Manuale utente

Manuali Magazzinaggio popolari di altre marche

QNAP

QNAP TS 32PXU Series Manuale utente

LaCie

LaCie RUGGED RAID Manuale utente

Freecom

Freecom CLS DOCK Manuale utente

PNY

PNY Attache P-FD64MBATT3 Manuale utente

HP StorageWorks MSL2024 Manuale utente

OLT

OLT 6x6 Maximizer Manuale utente

Transcend

Transcend JetFlash 160 Manuale utente

LaCie

LaCie RUGGED MINI Manuale utente

Thunderbolt

Thunderbolt 600 Manuale utente

Panasonic

Panasonic LB-DH8 series Manuale

LaCie

LaCie 12big Thunderbolt 3 Manuale utente

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuale utente

Panasonic

Panasonic LKM-F931-1 Manuale utente

Tabernus

Tabernus Enterprise Erase E2400 Manuale utente

Rocstor

Rocstor COMMANDER 3F series Manuale utente

HP P9000 Manuale utente

Western Digital

Western Digital Ultrastar Data60 Manuale utente

Dell

Dell PowerVault MD3600f Series Manuale utente